EFFECT OF RARE EARTH ELEMENT Er ON STRENGTHENING OF INTERFACE OF Ti（C，N） BASED CERMETS

ＥＦＦＥＣＴＯＦＲＡＲＥＥＡＲＴＨＥＬＥＭＥＮＴＥｒＯＮＳＴＲＥＮＧＴＨＥＮＩＮＧＯＦＩＮＴＥＲＦＡＣＥＯＦＴｉ（Ｃ，Ｎ）ＢＡＳＥＤＣＥＲＭＥＴＳ￥ＬｉｕＮｉｎｇ（ＤｅｐａｒｔｍｅｎｔｏｆＭａｔｅｒｉａｌｓＳｃｉｅｎｃｅａｎｄＥｎｇｉｎｅｅｒｉｎｇ，...     

Electrochemical behavior of Cu(Ⅱ) reduced in CH3OH and DMSO

The cyclic voltammetry and the potential-time curve after galvanostatic electrolysis were used to study the electrode processes of Cu(Ⅱ) in CH3OH solution and DMSO solution. The electroreduction of Cu(Ⅱ) to Cu on a Pt electrode proceeds in two steps: Cu(Ⅱ) + e = Cu(Ⅰ); Cu(Ⅰ) + e = Cu. The reduction potential of Cu(Ⅱ) in DMSO solution is more negative than that in CH3OH solution, and the diffusion coefficient of Cu(Ⅱ) ion in DMSO solution is larger than that in CH3OH solution because the polarity of DMSO is larger than that of CH3OH observably and has a stronger solvating power.     

一种金属线材制件的手动绕弯模

多品种，小批量，大尺寸的对称线材制件，采用手动绕弯模弯曲能提高经济效益，本文介绍了其模具结构与应用实例。     

弹性反向弯曲模设计

分析了一带有反向弯曲的零件的成形工艺 ,设计了1副一次完成2个不同位置侧耳反向弯曲的弹性弯曲模 ,这种结构可以推广到一次完成多个不同位置侧耳的反向弯曲 ,提高了生产效率和经济效益。     

铸造铝合金在多轴非比例载荷下的低周疲劳行为研究

主要研究了356铸造铝合金在多轴非比例载荷下的低周疲劳性能。结果表明，合金在循环变形过程中表现为循环硬化特征，循环硬化的程度表现出对非比例加载路径的依赖性；在相同等效应变幅值下，合金的非比例加载低周疲劳寿命小于比例加载，且非比例加载低周疲劳寿命也表现出对非比例加载路径的依赖性；在多轴疲劳寿命预测模型中考虑非比例加载路径对疲劳寿命的影响可以大大提高寿命模型预测的精确度。     

弯曲回弹逆解公式及其在焊管预弯机组设计中的应用

根据小曲率弯曲成形的特点，考虑了板料弯曲的纯弹性变形部分对回弹的影响，推导出根据板料强度、厚度和最终成形半径直接计算弯曲半径的回弹逆解公式，并应用于大口径UOE焊管预弯成形的设计上。根据计算公式给出了B-X100钢级板料UOE焊管预弯成形的预弯辊半径优化设计诺谟图。     

Numerical analysis of dimension precision of U-shaped aluminium profile rotary stretch bending

In order to enhance the dimension precision of bent part, advanced bending technologies is requested recently. Rotary stretch bending（RSB） is a suitable technology to realize high precision of bent part. The effect of processing parameters, namely the side pressure and the stretching force, on the dimension precision of aluminium profile RSB part was studied by finite element method. The numerical simulation of the U-shaped aluminium profile RSB was carried out, and the validity of the simulation was checked. Parametric analysis shows that the section distortion of the U-shaped profile LY 12M bent part decreases with the increasing of the side pressure, whereas the springback of curvature increases, and that both of the section distortion and the springback of curvature decrease with the increasing of the stretching force, moreover, the uniformity of curvature of the bent part is clearly enhanced with the increasing of the stretching force. The results above prove that RSB technology can better improve the dimension precision of aluminium profile bent part.     

无心弯管胎模设计

介绍了在使用无心弯管模弯曲管子的过程中存在的缺陷和采取的措施。通过采用增加弯管模具的夹紧块和镶块对毛坯的刚性约束来消除管内壁起褶的缺陷，采用固定数值法来解决管弯曲卸载后的弹性回跳的缺陷。介绍了在弯管模具设计中，前、后导向轮参数的选取方法以及根据管子的弯曲半径和弯管直径来分情况讨论其弧槽曲线的确定方法，避免在弯曲过程中弯管发生畸变，为设计弯管模具提供理论依据。     

U形接触片多工位级进模设计与制造

针对U形接触片的技术要求,确定了合理的冲压工艺方案,阐述了该多工位级进模设计要点,产品质量达到设计要求。同时,还介绍了楔块装置及磷铜薄片整形的微调装置。     

LOW CYCLE FATIGUE OF Cr-Mn-N STAINLESS STEEL

An investigation was conducted to examine the low cycle symmetric push-pull fatiguebehaviour of the Cr-Mn-N dual-phase stainless steel.Two groups of specimens,A and B,were used,they were solution treated at 1050 and 1250℃,respectively.The.fatigue life ofgroup A is almost twice as long as that of group B under the same total strain amplitude.Theenergy loss during the fatigue tests and the mophology of the fracture surfaces have been stu-died and discussed.