Design and experimental investigation of the high efficiency 1.5 W/4.2 K pneumatic-drive G-M cryocooler

The development of a high cooling power and high efficiency 4.2 K two stage G-M cryocooler is critically important given its broad applications in low temperature superconductors, MRI, infrared detector and cryogenic electronics. A high efficiency 1.5 W/4.2 K pneumatic-drive G-M cryocooler has recently been designed and developed by ARS. The effect of expansion volume rate and operation conditions on the cooling performance has been experimentally investigated. A typical cooling performance of 1.5 W/4.2 K has been achieved, and the minimum temperature of the second stage is 2.46 K. The steady input power of the compressor at 60 Hz is 6.8 kW, while the operation speed of the rotary valve is 30 rpm. A maximum cooling power of 1.75 W/4.2 K has been obtained in test runs.     

东兴铝业嘉峪关分公司铝灰渣循环利用研究

铝灰渣是铝熔铸过程中产生的废弃物。本文主要介绍了酒钢东兴铝业嘉峪关分公司铝灰渣的产生量、排放、利用情况、化学成分及表面特征,并简要介绍了铝灰渣、铝灰的循环利用途径。     

Effect of strain rate on the dynamic compressive mechanical behaviors of rock material subjected to high temperatures

Strain rate is not only an important measure to characterize the deformation property, but also an important parameter to analyze the dynamic mechanical properties of rock materials. In this paper, by using the SHPB test system improved with high temperature device, the dynamic compressive tests of sandstone at seven temperatures in the range of room temperature to 1000 °C and five impact velocities in the range of 11.0–15.0 m/s were conducted. Investigations were carried out on the influences of strain rate on dynamic compressive mechanical behaviors of sandstone. The results of the study indicate that the enhancement effects of strain rates on dynamic compressive strength, peak strain, energy absorption ratio of sandstone under high temperatures still exist. However, the increase ratios of dynamic compressive strength, peak strain, and energy absorption ratio of rock under high temperature compared to room temperature have no obvious strain rate effects. The temperatures at which the strain rates affect dynamic compressive strength and peak strain most, are 800, and 1000 °C, respectively. The temperatures at which the strain rates affect dynamic compressive strength and peak strain weakest, are 1000 °C, and room temperature, respectively. At 200 and 800 °C, the strain rate effect on energy absorption ratio are most significant, while at 1000 °C, it is weakest. There are no obvious strain rate effects on elastic modulus and increase ratio of elastic modulus under high temperatures. According to test results, the relationship formula of strain rate with high temperature and impact load was derived by internalizing fitting parameters. Compared with the strain rate effect at room temperature condition, essential differences have occurred in the strain rate effect of rock material under the influence of high temperature.     

Friction compensation controller for load varying machine tool feed drive

The load applied to a machine tool feed drive changes during the machining process as material is removed. This load change alters the Coulomb friction of the feed drive. Because Coulomb friction accounts for a large part of the total friction the friction compensation control accuracy of the feed drives is limited if this nonlinear change in the applied load is not considered. This paper presents a new friction compensation method that estimates the machine tool load in real time and considers its effect on friction characteristics. A friction observer based on a Kalman filter with load estimation is proposed for friction compensation control considering the applied load change. A specially designed feed drive testbed that enables the applied load to be modified easily was constructed for experimental verification. Control performance and friction estimation accuracy are demonstrated experimentally using the testbed.     

异构分层无线网络中基于逗留时间的动态流量均衡算法研究

为使异构分层无线网络能服务更多的移动用户,提出了一种基于逗留时间的动态流量均衡算法.该算法首先根据用户移动模型计算其在小区内的逗留时间,然后基于小区呼叫到达率和重叠覆盖小区的流量状态来确定一个周期内呼叫转移的数量,最后依据逗留时间门限值将重负载小区中满足条件的呼叫转移到轻负载的重叠覆盖小区中.为降低切换呼叫掉线率,还对异构网间的呼叫切换策略做了改进.仿真实验结果表明,本算法在新呼叫阻塞率和切换呼叫掉线率等性能指标上比传统方法有显著的提高.     

四川盆地上三叠统划分对比研究

四川盆地上三叠统对比长期存在混乱，给盆地整体评价带来困难。通过岩石地层、地震地层、事件地层及高分辨率旋回地层等多种方法讨论了须家河组与香溪群各岩性段的对比关系，得出了全盆地上三叠统的对比关系；指出须四段底可近似看成等时界面；须家河组下部地层自西向东、向南逐层超覆在雷口坡组之上，上部地层在盆地西北部自东南向西北方向剥蚀层位渐次变老。文章建议四川盆地上三叠统废除“香溪群”，统一使用“须家河组”，以利于对全盆地上三叠统进行油气资源整体评价与深化研究。     

Electrochemical synthesis and characterization of chloride doped polyaniline

Chloride doped polyaniline conducting polymer films have been prepared in a protic acid medium (HCl) by potentiodynamic method in an electrochemical cell and studied by cyclic voltammetry and FTIR techniques. The FTIR spectra confirmed Cl^- ion doping in the polymers. The polymerization rate was found to increase with increasing concentration of aniline monomer. But the films obtained at high monomer concentration were rough having a nonuniform flaky polyaniline distribution. Results showed that the polymerization rate did not increase beyond a critical HCl concentration. Cyclic voltammetry suggested that, the oxidation-reduction current increased with an increase in scan rate and that the undoped polyaniline films were not hygroscopic whereas chloride doped polyaniline films were found to be highly hygroscopic.     

循环伏安法在润滑油检测中的应用

介绍了循环伏安法的产生背景、原理。应用该技术可以快速、方便地对润滑油中抗氧剂、总酸（碱）值进行测定，并且可以对不同厂家润滑油的抗氧剂包进行区别。该技术还可以有效地评价润滑油的使用寿命和设备工作状况。     

对CFG桩质量缺陷的探讨

根据具体工程的概况及水文地质条件，分析了CFG桩在地下水位出现大面积缩颈现象和复合地基载荷试验达不到设计要求的原因，并介绍了地基补强措施，以满足工程质量的要求。     

结构振动试验转接器的设计及安装问题

一些产品及其相关部件在作振动试验时，由于产品的外形或特殊要求不能直接安装在振动台面上，需要通过特别设计的转接器（夹具）来进行连接，这种夹具实际上是一种附加结构，它作为台面与试件之间的中介，如设置不当将影响振动试验结果的可靠性。本文通过对某事例的分析与研究，从试验频带、允许误差、跟随条件以及安装共振频率等方面阐明与讨论了相关夹具的特性、设计原则与安装等问题。