输入——输出迭代算法中松弛因子的确定

本文利用变分的手段提示了输入—输出迭代算法中松弛因子的取值规律。     

The concept of an endurance limit for adhesive joints

The effect of cyclic stressing on the strength of single lap adhesive joints has been studied and a considerable reduction in strength observed when the maximum stress exceeds about 40% of the ultimate tensile strength, but whether or not a true endurance limit exists is not proven. Fallacies are shown in some of the techniques which have been proposed for studying the fatigue behaviour of adhesive joints.     

线性分组码的神经网络译码

介绍了神经网络与线性分组码之间的关系，并在文献[1]的基础上证明了软判决译码与求解能量函数最大值之间的等价性，然后以(7，4，3)汉明码为例介绍了神经网络在循环码硬判决、软判决译码中的应用。     

A modified rainflow counting method

The rainflow counting method is commonly recognized to be a good cyclic counting method in fatigue life prediction and for testing engineering components and structures. However, it has some shortcomings, which are pointed out in this paper in connection with the analysis of the stress-strain response. A modified rainflow counting method is presented. Case studies show that all the cycles really existing in the stress-strain response that cannot be counted by the rainflow counting method can be counted by the modified rainflow counting method. So it can be said that the modified rainflow counting method is a more reasonable cycling counting method than the traditional rainflow counting method.     

Microscopic fatigue processes in a plain-weave glass-fibre composite

This paper focuses on the microscopic damage and progressive failure of a composite reinforced by plain-weave glass cloth under tensile fatigue loading. The fatigue process was divided into three stages like that of multi-directional laminates. It was found that the internal damage at each stage (matrix cracks, debonds in the weft, successive debonds in the warp and ‘metadelaminations’ between warps and wefts) occurred near the cross-over point of the fabric. The modulus decay mechanism was explained by considering the progression of this internal damage. From the end of the first stage to the beginning of the middle stage, a characteristic damage state (CDS) (called a ‘meta-CDS’) was observed. It was found that woven composites have a unit area of damage accumulation (called a ‘unit cell’) and the damage of each unit cell and its distribution control the total fatigue damage of the material.     

杜84断块超稠油开发中后期稳产对策研究

对杜84断块超稠油生产中后期暴露的主要矛盾，即随着轮次升高，周期吞吐效果变差，井下技术状况日益变差。油层动用不均，汽窜加剧等问题进行了分析。并提出了相应的稳产对策-实施多井整体吞吐，大修复产，调剖等措施。现场应用证明，这些措施基本能够确保杜84断块超稠油中后期的稳产。     

Micromechanical characterisation of fibre/matrix interfaces

Theoretical analyses for the single fibre pull-out and push-out models under monotonic loading are given which are based on a shear-lag analysis in a fracture mechanics approach considering non-constant friction at the debonded interface as a result of fibre Poisson contraction (or expansion). The solutions allow the determination of typical fibre/matrix interfacial properties such as the interfacial fracture toughness, G_ic, the coefficient of friction, μ, and the residual clamping stress, q₀. Under cyclic loading the interfacial properties are expected to degrade as a result of repetitive abrasion, and a power law function is assumed between μ and the number of elapsed cycles, N. However, G_ic is assumed to be unaffected and a fracture mechanics based debond criterion is derived for the relationship between the external applied stress, the debond length and the reduced friction coefficient for both fibre pull-out and fibre push-out. In addition, the relative displacements between the free fibre end and the matrix top are obtained for cyclic fatigue when the fibre is loaded and unloaded. A relationship obtained for the protrusion (or intrusion) length in fibre pull-out (or push-out) experiments allows the severity of the interface frictional degradation to be evaluated and characterised. Similarities and differences in the frictional degradation behaviour between fibre pull-out and push-out are also identified.     

Cyclic strength of parts with overlapping zones formed by roller burnishing

The authors study residual stresses in and cyclic strength of shaft with overlapping zones formed during roller burnishing. The most significant decrease in fatigue strength is shown to occur in the presence of an overlapping zone with the areas arising due to a lowered roller burnishing pressure in the second pass. __________ Translated from Problemy Prochnosti, No. 3, pp. 144–148, May–June, 2006.     

带有块间串扰MC-CDMA的时域信道估计和多用户检测

本文把带有IBI的MC-CDMA系统等效解释为特殊的直接序列码分多址（DS-CDMA）系统，并给出了相应的时域信道估计方法和时域线性最小均方误差（MMSE）多用户检测方法。仿真实验表明了本文方法的性能。