掺气减蚀保护作用的新概念

利用针式掺气流速仪测量原型和模型掺气浓度场、流速场，气泡尺寸及其概率分布的研究成果表明，原型水流韦伯数高，形成微小气泡的能力比模型强，气泡上浮慢，接近底部的小尺寸气泡概率及掺气浓度比模型大。初步研究认为：0.2mm或0.5mm以下的微小气泡在掺气减蚀中起着主要作用，可能只要很小掺气浓度即可达到掺气减蚀的效果。因此以小尺寸气泡的掺气浓度，作为判断掺气减蚀保护作用的指标将更为准确。     

低密度微泡沫压井液的研究与应用

吐哈油田部分区块地层压力系数小于0.9,常规水基压井液对储层伤害大,若使用油基压井液成本高,环境污染严重。通过实验优选出了一种低密度水基微泡沫压井液。该压井液具有密度低、泡沫强度高、稳定性好、携砂能力强等优点。现场应用表明,低密度微泡沫压井液稳定时间大于48 h,密度在0.70~0.99 g/cm3之间可调,抗油污染能力强,抗油大于8%,抗温在100℃以上,岩心污染后渗透率恢复值大于80%;并且施工方便,成本低,具有储层保护能力,使用微泡沫压井液的井表皮系数在0.20~2.34之间。     

Noise-Assisted Signal Reception in Threshold Neuron

1IntroductionSometi mes,noise can i mprove signal transmission orsignal processing in a nonlinear system.This phe-nomenonis the so-called Stochastic Resonance(SR)[1].Most studies of SRinvolve asubthresholdsignal througha single nonlinear systemand the non…     

On the corrosion fatigue crack initiation model and expression of metallic notched elements

In the present study, attempts are made to extend the application of the mechanical model for the fatigue crack initiation (FCI) and the FCI life formula of metallic notched elements in laboratory air to those in the corrosive environment. The test results and analysis of the corrosion FCI (CFCI) life of aluminum alloys and Ti---6A1---4V show that the expression of the CFCI life obtained by modifying the FCI life formula in laboratory air can give a good fit to the test results of the CFCI life. The salt water (3.5% NaCl) environment has no effects on the CFCI resistant coefficient compared with the FCI resistant coefficient in laboratory air. However, 3.5% NaCl environment greatly decreases the CFCI threshold of aluminum alloy, but has little effect on the CFCI threshold of Ti---6A1---4V. The loading frequency ranging from 1 Hz to 10 Hz has no appreciable effect on the CFCI life, and thus, the CFCI threshold of aluminum alloys investigated. Hence, the expression for the CFCI life of metallic notched elements proposed in this study is a better one, which reveals a correlation between the CFCI life and the governing parameters, such as, the geometry of the notched elements, the nominal stress range, the stress ratio, the tensile properties and the CFCI threshold. However, this new expression of the CFCI life needs to be verified by more test results.     

自适应阵对角线加载研究

本文分析了对角线加载对自适应阵性能的影响，提出了加载门限的概念，以及加载门限的计算公式，为加载量的选取提供了方法和依据，并将加载研究的结果加以推广，提出了有效的ＬＳ自适应波束形成算法的非零初始化方法。     

BP算法的改进及用模拟电路实现的神经网络分类器

基于用模拟电路实现神经网络分类器的目的，对多层静态前馈神经网络的ＢＰ算法做了改进，采用线性限幅函数代替Ｓｉｇｍｏｉｄ函数作为神经元的激活函数，给出了改进的ＢＰ算法。对该算法性能的实验研究表明：这种改进算法不但方便了用线性模拟集成运算放大电路实现神经网络，而且具有学习速度快，映射能力强等优点。根据本文算法设计的神经网络分类器，无论是计算机仿真，还是模拟电路实现，都得到了比较高的识别率。     

A new monitoring system for piping systems in fossil fired power plants

A CEC-funded project has been performed to tackle the problem of producing an advanced Life Monitoring System (LMS) which would calculate the creep and fatigue damage experienced by high temperature pipework components. Four areas were identified where existing Life Monitoring System technology could be improved:

1. 1. the inclusion of creep relaxation

2. 2. the inclusion of external loads on components

3. 3. a more accurate method of calculating thermal stresses due to temperature transients

4. 4. the inclusion of high cycle fatigue terms.

The creep relaxation problem was solved using stress reduction factors in an analytical in-elastic stress calculation. The stress reduction factors were produced for a number of common geometries and materials by means of non-linear finite element analysis. External loads were catered for by producing influence coefficients from in-elastic analysis of the particular piping system and using them to calculate bending moments at critical positions on the pipework from load and displacement measurements made at the convenient points at the pipework. The thermal stress problem was solved by producing a completely new solution based on Green's Function and Fast Fourier transforms. This allowed the thermal stress in a complex component to be calculated from simple non-intrusive thermocouple measurements made on the outside of the component. The high-cycle fatigue problem was dealt with precalculating the fatigue damage associated with standard transients and adding this damage to cumulative total when a transient occurred.

The site testing provided good practical experience and showed up problems which would not otherwise have been detected.     

聚合物降解产物伤害与糖甙键特异酶破胶技术

综述了钻井，完井，尤其是水力压裂作业中产生的多糖类聚合物伤害和应用糖甙键特异酶破胶，解除多糖类聚合物伤害的技术。第一节报道了聚合物降解产物造成的伤害，指出冻胶破胶液粘度低并不代表压裂液已从充填裂缝中充分返排，氧化破胶剂和普通酶破胶剂不能使多糖类聚合物充分降解，产生的大分子量，水不溶的降解产物可对地层造成伤害，消除伤害的办法是采用对糖甙键有特异性的各种水解酶作压裂液破胶剂或伤害地层处理剂。第二节报道了各种聚合物（纤维素，瓜尔胶，淀粉）糖甙键特异酶降解聚合物的机理。第三节报道了糖甙键特异酶（主要针对瓜尔胶）的应用性能测试及结果，包括岩心流动实验，含糖量和分子量测定，传导性测试。第四节介绍了糖甙键特异酶消除聚合物伤害和用作压裂液破胶剂的现场应用，包括选井原则，实施工艺要点及3个典型井例。     

储层敏感性快速预测软件在大港油田的研究与应用

在储层特征分析，室内实验，机理研究的基础上，利用人工神经BP网络建立预测模型，并编制了预测储层5种敏感性的软件，该软件受人为因素干扰小，所需参数少，准确度高，综合符合率大于80％现场应用结果表明，该技术能为制定保护油气层技术措施提供较可靠的依据，能提高油田滚动开发效益，改善老油田的开发效果，该软件对BP算法进行了改进，（1）从两方面入手使网络摆脱平坦区，一是对输入数据进行归一化处理，使O1的取值在[0,1]之间，二是一旦网络陷入平坦区域，局部极小，使连接权值Wkj,Wji和阈值Qk,Qj同时缩小一个因子，λ＞1，可使Ok(1-Ok)脱离零值，离开平坦区；（2）加速收敛，方法有自动调整学习因子，添加动量项以及对权值进行批处理，用BP算法预测储层潜在敏感性，首先应确定影响储层敏感性的主要因素，然后根据这些因素有针对性地收集有关资料并进行处理，再根据敏感性预测的要求，设计相应的网络结构进行训练，最后对训练好的网络进行.检验。     

大庆油田套损井打通道加固技术

介绍了大庆油田近几年在套损井打通道加固技术方面取得的技术进步，在磨铣打通道技术上主要对钻铣工具的结构进行了优化设计及合理及合金刀块的优选组合，提高了磨铣效率，缩短了施工周期；在爆炸打通道技术中设计了安全隔爆装置，提高了施工的安全性，使爆炸扩径技术得到完善；Φ106mm密封加固技术的研制成功，取代了Φ100mm密封加固技术，为套损井修复后的完井工艺提供有效的技术支持，提出了大庆油田目前在套损井打通道加固方面存在的难题，结合国外在套损井打通道加固方面技术的新发展，对现有技术的局限性进行了分析，提出了今后技术攻关的方向。