涂料原料和涂层厚度对反射隔热保温性能影响研究

通过研究涂料配方中所用乳液、颜料、常规填料和隔热填料在红外灯下的反射、隔热和保温性能，发现高折射率的二氧化钛和含有微孔的硅藻土具有最佳的反射和隔热保温效果，轻质碳酸钙和重质碳酸钙具有一定的隔热保温作用，而理论上具有隔热保温效果的填料海泡石等并没有预期的效果。涂层厚度对隔热保温效果具有一定影响，但是没有颜料和填料的影响大。隔热涂料使用的填料应含有硅藻土、二氧化钛以及一些常规的填料。     

负离子分解室内有机化合物的测试

低浓度、高毒性的挥发性有机化合物(VOC)污染大气,造成“病态建筑综合症(SBS)”,严重威胁着人们的身体健康。空气中的负离子除有利于人体生理健康以外,还能有效分解空气中的VOC。将一种负离子添加剂添加到墙体涂料中,可以得到一种能有效释放负离子的涂料。本文测试了涂刷负离子添加剂涂料的测试小室中负离子分解总挥发性有机化合物(TVOC)及甲醛的性能,结果证明:涂料释放的负离子能有效分解VOC,使室内VOC的浓度在较短时间内满足GB/T—18883—2002的要求。     

硅溶胶—苯丙乳液复合路标涂料的研制

采用正硅酸乙酯(TEOS)为主要原料,以聚合溶胶法制备硅溶胶,制得的硅溶胶与苯丙乳液冷拼复配得到复合基料,再以该基料制得硅溶胶—苯丙复合路标涂料。通过正交试验分别确定了制备硅溶胶、硅溶胶—苯丙复合乳液和硅溶胶—苯丙复合路标涂料的最优方案。     

白色纯聚酯粉末涂料的性能研究

简要介绍了粉末涂料的特点 ,并从涂膜性能的优化角度论述了粉末涂料原料的选择和使用情况。从羧基聚酯树脂 -TGIC体系纯聚酯粉末涂料配方设计入手 ,研究了基料、填料、助剂对其涂膜性能 (主要物理机械性能 :涂膜之耐冲击力、柔韧性、倾斜流动性、硬度、附着力、抗UV老化等 )的影响 ,得到了一个在给出原料中涂膜综合性能最好的配比     

锌基水系复合涂层——达克罗表面处理技术

介绍了锌基水系复合涂层——达克罗表面处理技术的抗蚀机理和优异性能。     

含纳米ATO聚氨酯弹性抗静电涂料

以脂肪族聚氨酯弹性树脂为基体，透明纳米ATO导电粉为导电介质，添加超分散剂，采用物理与化学相结合的分散方法对纳米ATO进行预处理。主要解决纳米粒子的分散与团聚的难题，制备出可常温固化、颜色可调的含纳米ATO聚氨酯弹性抗静电涂料。讨论了基体树脂、纳米ATO含量、超分散剂种类与加量、研磨时间以及助剂等因素对抗静电涂料的表面电阻、耐候性、弹性、强度以及稳定性等性能的影响。同时对涂料的性能进行了测试与表征。     

自清洁外墙涂料的研究与应用

如何提高外墙涂料的自清洁能力,并使之保持较长的装饰效果一直是涂料界关注的热点。本文综述了微粉化技术、荷叶效应、气球陶瓷理论、自分层技术以及光催化效应的原理,及其在改善外墙涂料自清洁性方面的应用。     

模数对无机富锌涂料和涂层性能的影响

硅酸钾富锌涂料是目前广泛使用的钢铁防腐蚀涂料。作为涂料粘结剂的高模数硅酸钾溶液对涂料和涂层的性能有重要影响。本研究考察了硅酸钾粘结剂的模数变化对涂料及涂层性能产生的影响。实验结果表明：粘结剂模数的提高可以提高固化后涂层的耐水性能，当粘结剂模数在5.0左右时，所得富锌涂层具有最佳的耐磨性能，但当粘结剂模数超过5.5时会造成涂料施工性能和贮存稳定性下降，涂层柔韧性降低，从而降低涂层的耐磨性能。     

Polymeric sol–gel coatings as protective layers of aluminium alloys

Sol–gel route is an emerging technology to synthesize coatings of a wide variety of properties taylored. In this work three low temperature cured coatings has been studied to evaluate their protective properties in order to be used as protective barrier coatings for aluminium alloys with potential architectural and automotive applications. These three coatings are novel modified silane nanocomposites coatings obtained mixing two sols separately prepared: a pre-hydrolysed 3-glycidyloxypropyl trimethoxysilane (GPTS) with acidic catalyst and another obtained from tetraethylorthosilicate/methyltriethoxysilane (TEOS/MTES). Particulated coatings were obtained by addition of 25 wt.% particles of Aerosil 300 and Aerosil R972, respectively. The protective properties of the coatings were evaluated by electrochemical impedance spectroscopy (EIS) which showed notably differences among them not only from the protective viewpoint but the hydrophobic nature of the coatings and the controlling corrosion mechanism in each case.     

Thermodynamic Analysis of Chemical Vapor Deposition of BN + AIN Composite Coatings

Thermodynamic calculations were performed using a modified solgasmix-pv computer program in order to study the feasibility of codepositing boron nitride (BN) plus aluminum nitride (AIN) by chemical vapor deposition. Reactants considered were AICl₃, BCl₃ or B₂H₆, NH₃, and H₂. Deposition diagrams were generated for the BCl₃-AICl₃-NH₃ system over a range of processing conditions such as temperature, total system pressure, and reagent concentrations. Codeposition of BN + AIN was predicted by the calculations for temperatures in the range of 900 to 1700 K and pressures of 10.13 to 101.3 kPa. The predicted deposition efficiency at equilibrium was much higher for BN than for AlN at most reagent compositions. The AlN deposition efficiency increased with decreasing temperature and decreasing BCl₃ content, with increasing NH₃ content, or with the addition of H₂. Aluminum chlorides were found to be the dominant gaseous species.