Multi‐layered flat‐surface micro‐optical components directly molded on an LCD panel

Abstract— We have developed a process to fabricate optical components, such as a lens, prism, or diffuser, directly on to a glass substrate. Processes include precision mastering by diamond cutting and multi‐layer photopolymer (2P) molding to realize flat surfaces and the integration of multiple components with an alignment within a few micrometers.     

CVD金刚石膜生长过程的Raman分析

采用激光Raman散射分析法对CVD金刚石膜的生长过程进行研究 ,讨论在金刚石膜生长的不同阶段 ,膜内金刚石和非金刚石成分的相对含量及其残余应力的变化情况     

基于有限元分析的金刚石钻头强度验算公式

在对81／2B125金刚石钻头进行有限元计算分析后，找出最大应力点在金刚石钻头冠部切削告处。通过改变各相关尺寸和结构型式，用有限元法模拟试验过程，在给定结构参数和工艺参数情况下获得多组数据。根据专业知识，参考有限元计算获取的各组数据变化特征，选出拟合较好的公式类型，再采用回归分析方法确定待定系数，最后得出工程上实用的金刚石钻头强度验算公式。用这个公式对81／2B461W和121／4B331金刚石钻头进行了强度验算，经改进设计后钻头在现场使用取得了良好的效果。     

Synthesis of diamond crystals and films using an oxygen-acetylene flame under atmosheric pressure

Diamond growth with rates up to 100 to 140 μm/hr was achieved using an oxygen-acetylene combustion spraying technique in an atmospheric environment. Investigations on the processing indicated that the gas flow ratio, substrate position, substrate temperature, temperature distribution, and substrate pretreatment were the most important factors affecting the growth of diamond crystals. Evaluation by means of X-ray diffraction, Raman spectroscopy, scanning electron microscopy, and electron probe microanalysis showed that the synthesized diamond was nearly perfect in morphology, structure, and purity.     

The optimal diamond wheels for grinding diamond tools

Grinding is the most suitable process for manufacturing good quality diamond tools. In this paper, diamond wheels have been studied. From the grinding of polycrystalline diamond (PCD) insets, the effects of certain factors such as the bonding material, the grit size and structure of a diamond wheel have been investigated. It is concluded that vitrified bond diamond wheels are the most suitable for grinding PCDs and the recommended grit size is mesh number 1000, which can get a good surface quality within an appropriate time. The wheel structure is another important factor. Rougher wheels (mesh #800, #1000) with the softer grade scale P yield a higher material removal rate (MRR) than scale Q. However, a finer wheel (mesh #1200) needs a tougher structure to promote its grinding ability and to have a higher MRR.     

Characterization of temporal response, spectral responsivity and its spatial uniformity in photoconductive diamond detectors

Three photoconductive diamond detectors with highly oriented diamond (HOD) films fabricated by the same process were characterized with respect to temporal response, spectral responsivity and its spatial uniformity over the wavelength range from 190 to 250 nm. Temporal measurements showed a drift in the baseline, suggesting the presence of deep level carrier traps. The responsivity of specimen No. 2 was more than twice those of the other two specimens, but it showed an unpredictable current fluctuation. It was found that the spatial uniformities of all the specimens were too low for radiometric purposes. A prominent peak, thought to be due to photoemission, was found in the responsivity spatial distribution of specimen No. 3 under a negative applied voltage.     

Comparative study of the electrical properties of diamond films grown by microwave plasma assisted and hot-filament chemical vapor deposition

Schottky diodes were built on different polycrystalline diamond films grown by Microwave Plasma and Hot Filament Chemical Vapor Deposition and their electrical properties were studied. The barrier height increased with the diamond film quality and the corresponding ideality factor decreased. Even though the lower-quality HFCVD film displayed poor rectifying properties, it was found to be much less sensitive to variations in the operating conditions (air vs. vacuum). The activation energies of the films depend on morphological parameters, as preferable grain size or orientation. The bulk conduction also depends on the quality of the deposited films, changing from ohmic to trap-free or shallow trap SCLC and SCLC with an exponential distribution of traps. The hypothesis of using the electrical measurements as an indicator for film quality has been discussed.     

无氢类金刚石碳膜的研究进展

介绍了无氢类金刚石碳膜的制备方法 ,它们的机械、光学、电学性能 ,将无氢与含氢的类金刚石碳膜进行了简单比较 ,总结及探讨了它们的应用     

PDC钻头在胜利油田深井钻井中的应用

胜利油田为提高深井钻井速度，试验应用了PDC钻头，结果表明，深井钻井应用PDC钻头可大幅度提高机械钻速，缩短建井周期，降低钻井成本，经济效益明显。通过大量的现场试验，扩大了PDC钻头在胜利油田的使用范围，并取得很好的效果，初步形成了PDC钻头推广应用区域模式。详细介绍了胜利油田不适用PDC钻头钻进的地层岩性，给出了钻头选型及钻井参数选择原则，并对应用效果进行了分析。     

C－BN衬底上金刚石的异质外延生长研究

用热灯丝ＣＶＤ方法在Ｃ－ＢＮ单晶衬底上制备出金刚石膜，并且在Ｃ－ＢＮ（１００）面上观察到金刚石的异质外延。