Synthesis of amphiphilic magnetic microspheres by dispersion copolymerization of styrene and poly(ethylene oxide) macromonomer

Amphiphilic magnetic microspheres ranging in diameter from 5 to 100 µm were prepared by dispersion copolymerization of styrene and poly(ethylene oxide) vinylbenzyl (PEO‐VB) macromonomer (MPEO) in the presence of Fe₃O₄ magnetic fluid. The effects of various polymerization parameters on the average particle size were systematically investigated. The average particle size was found to increase with increasing styrene concentration and initiator concentration. It also increased with decreasing stabilizer concentration and molecular weight of MPEO. The content of the hydroxyl groups localized in the microspheres ranged from 0.01 to 0.2 mmol g^?1. © 2003 Society of Chemical Industry     

波动方程数值模拟的隐式差分法

在有限差分波动方程数值模拟中,通常采用高阶差分方法来提高空间导数的数值逼近精度,以实现降低数值频散,提高数值模拟精度的目的。首先对差分频散进行了理论分析;然后讨论了估计一阶空间导数的隐式差分格式,并与通常采用的高阶精度显式差分格式进行了对比分析,结果表明,隐式差分格式能够在更宽的波数范围使差分频散控制在可接受的水平,如8阶精度的显式差分格式所适应的波数带宽约为O．55kmax,而隐式差分格式所适应的波数带宽约为0．7kmax;最后通过模型试算,对隐式差分格式的有效性进行了验证。模拟结果表明,用隐式差分格式在一定程度上降低了差分频散,提高了模拟精度。     

16×10.7 Gb/s 1 600 km普通单模光纤环路传输研究

利用双折射光纤环设计了可调功率均衡滤波器,实现了16路16×10.7 Gb/s NRZ码、超过1 600 km常规单模光纤(SMF)的系统传输及性能测试,信道误码率均小于3×10-5(FEC纠错前).数值仿真并实验研究了对单环长度240 km、损耗超过80 dB的环路16路10.7 Gb/s波分复用(WDM)系统传输的优化.传输7圈后,功率均衡器降低了信道功率不平坦度超过5 dBm.     

Processing of Yttria-Alumina Coated Silicon Nitride Slips by Slip Casting

Si₃N₄powders coated with 6 wt% Y₂O₃and 4 wt% Al₂O₃were prepared by coprecipitation. The resulting powders were dispersed in water at different pH values and with addition of various amounts of ammonium polyacrylate (NH₄PA) to produce 32 vol% slips. The influence of the amount of NH₄PA solution added and pH on the rheological properties of 32 vol% coated Si₃N₄slips were studied. In addition, the sintered density of cast samples was determined and related to the degree of slip dispersion. The adsorption of the NH₄PA on the coated particle surface was rather high and the surface became saturated near 0.86 mg/m²at pH 9.2. High NH₄PA concentrations (1.7–3 wt%) were necessary to obtain well dispersed 32 vol% coated Si₃N₄slips at pH 9.2. The best stabilization was obtained with the addition of 2.3 wt% NH₄PA; in this condition, the viscosity reached a minimum value of 35 mPa.s at 100 s^–1. The slip viscosity increased with increasing pH from 9.2 to 10.2. Slips with low viscosities gave a more dense packing of cast samples and consequently higher sintered density values.     

Effect of ionic content,solid content,degree of neutralization,and chain extension on aqueous polyurethane dispersions prepared by prepolymer method

There are many variables in the preparation of aqueous polyurethane (PU) dispersions. Carboxylic acid content, solid content, degree of pre/postneutralization of the carboxylic acids, and chain extension all impact dispersion particle size, viscosity, pH, molecular weights, and glass transition temperature. This study evaluated the impact of these variables on a given PU dispersion formulation prepared from isophorone diisocyanate, an aliphatic polyester polyol, dimethylol propionic acid, and hexamethylene diamine with triethyl amine as the neutralizing base and N‐methyl pyrrolidone as the cosolvent. Changes in carboxylic acid content, degree of preneutralization, and chain extension were found to have the expected impacts on dispersions properties. Increased ionic content in the dispersion step led to lower particle size and higher viscosity, increased chain extension with its concurrent increase in molecular improved subsequent film properties. Surprising results were obtained by varying the amount of postneutralization and from increased solids content at the time of dispersion. Unexpectedly, both of these variations led to much higher dispersion viscosities and particle size in solution. To have these changes take place, it is theorized that there is a major change in solution morphology caused by these modifications. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci 98: 2514–2520, 2005     

Formation of composites fabricated by exothermic dispersion reaction in A1-TiO2-B2O3 system

The formation of aluminum matrix composites fabricated by exothermic dispersion reaction in A1-TiO2-B2O3 system was investigated. The thermal analysis results show that the reactions are spontaneous and exothermic. The Gibbs free energy of α-Al2O3 is the lowest among all the combustion products, followed by TiB2 and Al3Ti. It is noted that when the B2O3/TiO2 mole ratio is below 1, the reaction products are composed of particle-like α-Al2O3, TiB2 and rod-like Al3Ti. The α-Al2O3 crystallites, resulting from the reaction between A1 and TiO2 or B2O3, are segregated at the grain boundaries due to a lower wettability with the matrix. SEM micrographs show that rod-like Al3Ti phase distributes uniformly in the matrix. When the BEO3/TiO2 mole ratio is around 1, the Al3Ti phase almost disappears in the composites, and the distribution of α-Al2O3 particulates is improved evidently.     

JETS,PLUMES AND BUOYANT JETS IN STATIC ENVIRONMENT

Turbulence represents an essential aspect in atmospheric and oceanic circulations.In particu-lar,it is a preponderant factor in the dispersion of pollutants of artificial or natural origin.Thevertical turbulent jets,plumes and buoyant jets discharging into static environment is one of themost important and basic flow patterns related with the environment pollution.These flows havenumerous important applications,for example,thrust augmentors,waste disposal plumes fromstacks and combustion systems,and significant problems of turbulent diffusion.     

单模光纤最小群速度色散波长附近的调制不稳定性

利用修正的非线性Ｓｃｈｒｏｄｉｎｇｅｒ方程研究了单模光纤最小群速度色散波长附近的调制不稳定性，发现了一个新的由光纤四色散导致的调制不稳定性区域，该区域的调制范围与初始入射脉冲的功率和四阶色散有关。     

G.652光纤上的2.5Gbit／s色散受限系统

本文根据色散受限中继段长度的计算，对实际工程中１５５０ｎｍ波长２．５Ｇｂｉｔ／ｓ系统进行计算比较得出啁啾声引起的色散不容忽视，它使２．５Ｇｂｉｔ／ｓ成为色散受限系统。对１３１０ｎｍ波长６２２Ｍｂｉｔ／ｓ系统，当使用多纵模激光器时，往往也会成为色散受限系统。     

G.652光纤长途传输系统的色散补偿

针对当前国内长途传输光缆系统在扩容过程中，因光信号色散而影响传输质量的现象，结合实际工程建设，分析了光信号色散的危害及其成因，并提出了相应的解决办法及建议。