连轧机用人字轮齿轴断裂失效分析

用宏观断口分析、化学检验、力学性能测定、低倍检查、金相组织及夹杂物评定鉴别、受力分析及强度寿命定量估算的方法，对人字轮被动齿轴端断裂失效原因进行分析，并提出改进措施。     

强折射轴对称流场的干涉再现方法

利用光学方法测量气体状态参数的关键在于确定气体折射率场的变化。光线通过稳定的非均匀折射率场时发生偏折，并且在强折射对称场中会产生交叉，使得条纹位移量的判读困难。本文首先分析了光线在轴对称折射率场中的偏折效应，在此基础上，给出了一种利用成像透镜对强折射轴对称场中折射率的干涉再现方法。该方法与其它方法相比较能够精确地确定折射率ｎ（ｒ）的值。     

Electrochemical Aspects of Electroosmotic Dewatering of Clay Suspensions

An attempt is made to elucidate the electrochemical aspects of the electroosmotic dewatering (EOD) of clays as reported in some recent work, especially that on interrupted DC power electroosmotic dewatering published by Rabie, Mujumdar and Weber (2). These authors showed that the dewatering by EOD stops after the DC power has been on for several minutes or hours; on interruption of their power and on short-circuiting of the electrodes, conditions can be created again for some further dewatering by DC power EOD. This discovery, of Rabie et al. is interpreted as a fuel cell effect and it is shown that it affords clues to several other electrochemical strategies for the possible enhancement of the efficiency of the EOD by DC power.

Further, the open circuit potentials observed by Rabie et al. (2) on the interruption of DC power are given an electrochemical interpretation which leads to quantitative estimates in agreement with the experimental values.     

On the stability preserving property of the double bilinear transformation on a class of 2-D transfer functions

This paper addresses the BIBO (bounded-input bounded-output) stability of a class of discrete 2-D quarter-plane filters in the presence of nonessential singularities of the second kind (NSSK's) on the unit bidisk. Conditions under which the double bilinear transformation (DBT) preserves stability are derived. The results presented here also extend the class of systems whose stability can be predicted. Use of the inverse DBT to produce a continuous equivalent of the discrete 2-D transfer function allows easy application of a continuous-domain equivalent of a criterion developed by Dautov. The necessary and sufficient condition for stability derived in this work provides a simple check for the class of systems under consideration. From this class of systems, it is also possible to construct stable pairs of mutually inverse transfer functions.     

齿轮磨前滚刀的齿形研究

本文介绍了磨前滚刀滚切齿轮的最大根切量和磨后的渐开线长度计算,并建立了数学模型。为更加直观起见,还建立了模拟滚齿的数学模型。并在实验的基础上提出了参考标准。     

抽油机减速器齿轮的失效分析

找出了人字齿轮减速器在工作中右端齿轮出现严重磨损的原因并进行了分析。提出在国内现有制造技术的条件下，对于37kN·m以下的减速器应推广使用斜齿轮传动。     

对水厂一期滤池技术改造后的经济评价

本文主要从经济角度分析净水厂实际生产情况及经济技术指标等方面的数据。阐述福州西区水厂一期滤池由原先双阀滤池改造成V型滤池的经济性。     

内外齿复合冷挤压成型实验研究

通过对轿车转向盘毂件内外齿进行的复合挤压实验研究 ,得到了新式复动式复合挤压模具结构 ,并确定了一种合理的成型工艺方案     

X射线三轴晶衍射法测量半绝缘GaAs单晶的化学配比

采用X射线三轴晶衍射法,根据As间隙原子对作为过量As在GaAs单晶材料中存在的主要形式的模型,可以无损、高精度测量半绝缘GaAs单晶的化学配比.并探讨了引起晶格变化的原因及其与熔体组分的关系,对于制备高质量GaAs单晶及其光电器件具有重要的意义.     

大型对开组合齿圈工艺设计分析及其最优化

本文论述了大型齿圈的结构特征及其现行工艺的合理性；在建立工艺关键环节概念的基础上提出工艺优化方案。并从理论上论证了实现最优化的充分可能性。