DC-DC变换器突加负载时的动态性能研究

提出了一种能够有效改善DC-DC变换器动态性能的方案。该方案是在全桥电路基础上并联一单端正激变换电路，使变换器负载从10%轻载突加到100%满载时，其暂态过程小于1μs输出电压达到设计要求。文中对具体电路进行了详细分析，并通过仿真进行了验证。     

基于PLC电液比例控制的液力测功装置开发及其应用

本文介绍一种齿轮动态加载试验规范及技术要求，论述了运用电液比例控制技术所设计的液压加载系统原理及其使用效果，并简述由此构造的液力测功装置的原理与应用前景。     

无线移动自组网络的动态源路由策略

文章介绍无线移动自组网中动态源路由策略的路由发现和路由维护,并提出改进思路和今后研究的方向。     

应用频率-初速法测试推算单桩承载力须解决的几个关键问题

本文对当前频率 -初速法应用中存在的一些问题阐述了作者的看法并着重探讨桩振初速度V0的计算方法、W0 的正确单位、如何使桩 -土体系明显震动、怎样从激振曲线中突出及分离出桩振曲线 ,从而获得正确的桩振频率f0 和首波峰 -峰值Ad、动静对比系数 βv 的选取     

Transient Green’s Tensor for a Layered Solid Half-Space With Different Interface Conditions

Pulsed ultrasonic techniques can be and have been used to examine the interface conditions of a bonded structure. To provide a theoretical basis for such testing techniques we model the structure as a layer on top of a half-space, both of different elastic properties, with various interface bonding conditions. The exact dynamic Green’s tensor for such a structure is explicitly derived from the three-dimensional equations of motion. The final solution is a series. Each term of the series corresponds to a successive arrival of a “generalized ray” and each is a definite line integral along a fixed path which can be easily computed numerically. Willis’ method is used in the derivation. A new scheme of automatic generation of the arrivals and ray paths using combinatorial analysis, along with the summation of the corresponding products of reflection coefficients is presented. A FORTRAN code is developed for computation of the Green’s tensor when both the source and the detector are located on the top surface. The Green’s tensor is then used to simulate displacements due to pulsed ultrasonic point sources of known time waveform. Results show that the interface bonding conditions have a great influence on the transient displacements. For example, when the interface bonding conditions vary, some of the first few head waves and regular reflected rays change polarities and amplitudes. This phenomenon can be used to infer the quality of the interface bond of materials in ultrasonic nondestructive evaluation. In addition the results are useful in the study of acoustic microscopy probes, coatings, and geo-exploration.     

动态光散射法研究海藻酸钠凝胶松弛行为

在前文的基础上，用相关函数轮廓分析的方法剖析了运动模型模式的复杂性。通过海藻酸钠水溶液在０．１ｍｏｌ／ＬＣａＣｌ２水溶液透析凝胶化过程中交联网络的松弛时间谱表明它不是单一的峰，有两上特征运动模式，并随透析向更慢的运动模式发展，这很慢的运动模式估计与区域的结构的生成有关。     

热释电系数的测量方法

描述热释电系数的两种测量方法。其一为电荷积分法，测试系统简单，测量数据准确，且能满足零电场条件下的测量。其二为动态电流法，采用调制热源技术，研究在特定温度条件下热释电材料的动态热释电响应。     

风机叶轮的现场平衡方法

介绍了利用简单方法，解决风机叶轮现场静、动平衡的问题。方法快速、准确、实用。     

粘弹性圆柱壳在轴向恒压下的动力稳定性

基于Timoshenko-Mindlin假设,得到考虑粘弹性的各向同性圆柱壳及纤维增强正交铺设层合圆柱壳在轴向恒压下的动力学方程。文中对两端简支的圆柱壳进行了分析,依Laplace变换,导出动力稳定的特征方程,由Routh-Hurwitz判据建立动力稳定性条件,对两类圆柱壳讨论了横向剪切变形的影响。