Evaluating Liquefaction Strength of Partially Saturated Sand

A method is presented for evaluating the liquefaction strength of partially saturated sand using the compression wave velocity (P-wave velocity), a new indicator of saturation. Based on laboratory test results, an empirical correlation that relates the liquefaction strength with the pore pressure coefficient B is firstly proposed. The strength is defined as the cyclic stress ratio required to cause liquefaction at a specified number of cycles. With the aid of a theoretical relation between B and the P-wave velocity, an explicit correlation of more interest is then established between the liquefaction strength of sand and its P-wave velocity. A comparison of the predictions using this explicit correlation with laboratory measurements shows a satisfactory agreement. The significance of this method lies in that it makes it possible to evaluate the liquefaction strength of sand as affected by saturation through the measurement of P-wave velocity, which can be made not only in the laboratory but particularly in the field.     

一种高并行度的H.264帧内预测器的VLSI设计

分析了帧内预测的17种模式,对于每个4×4大小块的16个像素点的不同模式的预测公式之间的相同运算,采用数字强度缩减的方法去除计算的冗余,提出了一种高并行度的帧内预测器,可以每个时钟周期处理16个像素点的预测值。基于SMIC0.18μm工艺,用verilog对该设计进行了VLSI实现,综合后的电路的关键路径最大时延为10ns,电路规模不超过1.4万门,数据吞吐率可以达到1600Msamples/s。从实现结果来看,与采用可重构方法的设计相比,该设计在相同的并行度下减小了电路面积,简化了控制逻辑。     

Suppression of void coalescence in thermal aging of tin-silver-copper-X solder joints

Addressing the potential for drop impact failure of Pb-free interconnects, the shear ductility after extensive aging of Sn-Ag-Cu (SAC) solders has been improved radically by Co or Fe modifications. Several other SAC+X candidates (X=Mn, Ni, Ge, Ti, Si, Cr, and Zn) now have been tested. Solder joint microstructures and shear strength results show that new SAC+X alloys also suppress void formation and coalescence at the Cu (substrate)/Cu₃Sn interface (and embrittlement) after aging at 150°C for up to 1,000 h. Microprobe measurements of 1,000 h aged samples suggest that Cu substitution by X is usually accentuated in the intermetallic layers, consistent with X=Co and Fe results.     

Cyclic strength of parts with overlapping zones formed by roller burnishing

The authors study residual stresses in and cyclic strength of shaft with overlapping zones formed during roller burnishing. The most significant decrease in fatigue strength is shown to occur in the presence of an overlapping zone with the areas arising due to a lowered roller burnishing pressure in the second pass. __________ Translated from Problemy Prochnosti, No. 3, pp. 144–148, May–June, 2006.     

The influence of nanoadhesives on the tensile properties and Mode-I fracture toughness of bonded joints

Nanoadhesives of epoxy resin are synthesized and evaluated. They are organically modified by multiwalled carbon nanotubes (MWCNT) (1% by weight) as reinforcement. Tensile tests are conducted on multiple identical unnotched and notched specimens to evaluate the overloading and fracture behavior of the nanoadhesives and are compared with the neat epoxy resin. In comparison with the neat epoxy, it is found that the 1% MWCNT reinforcement increased the ultimate and residual strength by about 29% and 56%, respectively. In comparison with the neat resin, there is a 265% increase in the fracture toughness of the MWCNT adhesive. Fracture surface analysis revealed the various mechanisms by which the MWCNT adhesives acquire their superior strength and toughness in comparison with the neat resin.     

Pb/Sn凸剪切性能研究

在实际使用条件下,Pb/Sn凸点会由于承受温度循环而产生剪切应力,剪切应力导致的主要失效方式是开裂.通过对倒装焊后Pb/Sn凸点剪切强度的测量及对剪切后断口的分析,发现破坏主要发生在凸点下金属(UBM)层内部或UBM与Al焊盘之间,平均剪切强度受凸点尺寸影响很小,范围在21～24MPa。     

Obituaries: Martin Deutsch (1926-2002).

Reports the death of Martin Deutsch (1926-2002) and notes his contributions to the field of developmental psychology. Deutsch believed that environmental influences were critical for cognitive development during children's early years and that it was possible to design programs that would provide some of those experiences for children. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

西气东输工程用X70热轧板卷屈服强度检测值波动大的探讨

对西气东输工程用X70热轧板卷检验过程中出的屈服强度σ0.5波动大的情况进行了分析，认为拉伸试样弯曲是主要原因。这一问题可通过反复压平试样，确保试样的平直度以及适当提高钢的强度的方法加以解决。     

Maternal depression and early positive parenting predict future conduct problems in young children with attention-deficit/hyperactivity disorder.

Children with attention-deficit/hyperactivity disorder (ADHD) are at risk for adverse outcomes such as substance abuse and criminality, particularly if they develop conduct problems. Little is known about early predictors of the developmental course of conduct problems among children with ADHD, however. Parental psychopathology and parenting were assessed in 108 children who first met Diagnostic and Statistical Manual of Mental Disorders (4th ed.) criteria for ADHD at 4-7 years old. When demographic variables and baseline ADHD and conduct problems were controlled, maternal depression predicted conduct problems 2-8 years following the initial assessment, whereas positive parenting during the structured parent- child interaction task predicted fewer future conduct problems. These findings suggest that maternal depression is a risk factor, whereas early positive parenting is a protective factor, for the developmental course of conduct problems among children with ADHD. (PsycINFO Database Record (c) 2010 APA, all rights reserved)