镍氢电池负极用低成本储氢合金的研究

研究了ABS型储氢合金在低Co含量条件下，随B组元替代元素Co，Al，Si等含量的变化对合金电化学性能的影响规律，同时研究了A组元中不同La／Ce比对合金电化学性能的影响情况。结果表明，随合金中Co含量的降低，合金的活化性能和放电容量得以改善，但合金的循环寿命下降也比较明显；在试验范围内，随Al元素的加入，合金的循环寿命得以改善，但材料的放电容量和活化性能均有所下降；随合金La／Ce比的降低，合金的放电容量略有下降，但其循环寿命和放电电压平台有较大提高。     

Oxides Catalysts of Rare Earth and Transient Metal for Catalytic Oxidation of Benzene

The catalysts of CeO2 and the mixture of CeO2 and CuO were prepared, and the activities of these catalysts for completely oxidizing benzene were studied.The results show that the optimal proportion of CeO2/CuO is 6: 4.The highest temperature at which benzene was completely oxidized on these catalysts at different airspeed was measured.Compared these catalysts with the noble metal used, our catalysts had superiority in the resources and the industrial cost besides good activities.     

难处理金矿石加石灰焙烧焙砂中CaS的消除

介绍了用空气氧化预浸加石灰焙烧焙砂中的CaS，以消除其对金氰化的影响。预浸后金的氰化浸出率可从58％提高到80％以上。     

Catalytic oxidation of sulfide ions over nickel hydroxides

The catalytic sulfide ion oxidation by oxygen to elemental sulfur over β-Ni(OH)₂ and LiNiO₂ has been studied. As a result of experimental investigation performed, a reaction mechanism is suggested which involves heterogeneous and homogeneous processes. Dioxygen activation in the heterogeneous process proceeds via a redox Ni²⁺ ↔ Ni³⁺ transition and participation of OH⁻ groups. The active HO⁻₂ species thus formed carries on the reaction in homogeneous phase. Nickel hydroxides are promising catalysts for practical application.     

Reactivity of steam in exhaust gas catalysis III. Steam and oxygen/steam conversions of propane on a Pd/Al2O3 catalyst

A 1% Pd catalyst (38% dispersion) was prepared by impregnating a γ-alumina with palladium acetylacetonate dissolved in acetone. The behaviour of this catalyst in oxidation and steam reforming (SR) of propane was investigated. Temperature-programmed reactions of C₃H₈ with O₂ or with O₂ + H₂O were carried out with different stoichiometric ratios S(S =[O₂]/5[C₃H₈]). The conversion profiles of C₃H₈ for the reaction carried out in substoichiometry of O₂ (S < 1) showed two discrete domains of conversion: oxidation at temperatures below 350°C and SR at temperatures above 350°C. The presence of steam in the inlet gases is not necessary for SR to occur: there is sufficient water produced in the oxidation to form H₂ and carbon oxides by this reaction. Contrary to what was observed with Pt, an apparent deactivation between 310 and 385°C could be observed with Pd in oxidation. This is due to a reduction of PdO_x into Pd⁰, which is much less active than the oxide in propane oxidation. Steam added to the reactants inhibits oxidation while it prevents the reduction of PdO_x into Pd⁰. Compared to Pt and to Rh, Pd has a higher thermal resistance: no deactivation occurred after treatment up to 700°C and limited deactivation after treatment up to 900°C, provided that the catalyst is maintained in an oxygen-rich atmosphere during the cooling.     

Mechanical degradation of coating systems in high temperature cyclic oxidation

Cyclic oxidation tests were performed on a large variety of commercially available overlay coatings. The results of cyclic oxidation tests confirmed that the composition of the coating as well as the processing method of the coating can affect the life of the system. Coating life was determined by the time to coating penetration and initiation of substrate attack. As this work was part of a effort to evaluate the relative protectiveness of available coating systems for Industrial Gas Turbine applications at relatively high temperature, an extensive testing programme was undertaken. The different coatings were tested to visual failure. The results presented in this paper concentrate on the surface instability of the coating. Apart from usual oxidation of the coating an additional degradation mechanism was observed. A mechanical effect caused by the instability of the coating as a result of the difference in the thermal coefficient of expansion and mechanical properties between the substrate and coating. This effect, the so-called “rumpling” effect, resulted in a significant reduction in time to penetration and was in some systems the life controlling factor.     

Alkali-metal Na Adsorption and Promoted Oxidation on Si(100)2×1 Surface

The alkali-metal Na adsorption on Si(100)2×1 surface and its promoted oxidation and Si oxidegrowth have been investigated by means of thermal desorption,work function,Auger electronspectroscopy and photoemission electron spectroscopy.The experimental data showed that therewas a new state,interface electron state,near the Fermi level after the deposition of Na atoms.It wasfound that the presence of Na always caused an increase of the oxygen initial uptake whereas thepromotion of Si oxide growth was observed only at the coverage of Na greater than 0.5 ML.A newmechanism of Na-promoted Si oxide growth is suggested in this paper.     

Structural Description of Polyaromatic Nucleus in Residue

The proton nuclear magnetic resonance spectroscopy （1H-NMR）, the synchronous fluorescence spectrometry （SFS） and the ruthenium ions catalyzed oxidation （RICO） method were used to determine the chemical structure of polyaromatic nucleus in Oman residue fractions. The results of 1H-NMR analyses showed that the average numbers of aromatic rings in the aromatics, resins and asphaltenes units were 3.2, 5.6 and 8.2, respectively. SFS was used to investigate the distribution of aromatic rings in residue fractions, the main distribution range of aromatic rings in aromatics, resins and asphaltenes were 3 4 rings, 3--5 rings and more than 5 rings, respectively. The aromatic network in residue fractions was oxidized to produce numerous carboxylic acids. The types and content of benzenepolycarboxylic acids, such as phthalic acid, benzenetricarboxylic acids, benzenetetracarboxylic acids, benzenepentacarboxylic acid and benzenehexacarboxylic acid disclosed the condensed types of aromatic nuclei in the core. The biphenyl fraction （BIPH）, the cata-condensed fraction （CATA）, the peri-condensed fraction （PERI） and the condensed index （BCI） were calculated based on the benzenepolycarboxylic acids formed. The results implied that there was less biphenyl type structures in all residue fractions. The aromatics fraction was almost composed of the cata-condensed type system, and the asphaltenes fraction was wholly composed of the peri-condensed type system, while in the resins fraction co-existed the two types, herein the peri-con- densed type was predominant over the cata-condensed type. Based on the analytical results obtained in the study, the components --aromatics, resins and asphaltenes -- were given the likely structural models.     

Ti-45Al-10Nb合金的高温氧化行为

研究了Ti—45A1—10Nb(原子分数，％)合金在800-960℃在氧气和空气中的氧化行为．结果表明，该合金具有较好的高温抗氧化性能，其氧化增重速率与铁基耐热不锈钢相似或略优．与Ti—50A1合金相反，Ti-45A1-10Nb合金在空气中的氧化增重速率明显低于在纯氧中的氧化增重速率．X射线衍射与能谱分析表明，Ti-45Al一10Nb合金在氧气中的氧化产物主要有TiO2和Al2O3，但在空气中的氧化产物中有TiN相．这是降低氧化速率的主要原因，同时，合金元素Nb稳定了氧化层中的TiN相，因而提高了合金在空气中的抗氧化性能．     

High‐Performance,Monolithic Polyaniline Electrochemical Actuators

New polyaniline (PANI) asymmetric membranes were fabricated using a phase‐inversion technique with hexane as the coagulation bath. These membranes exhibit a dense structure with macrovoids distributed asymmetrically throughout the cross‐section. A stress–strain study demonstrated that the Young's modulus (1.421 GPa) and strain at break (7.6 %) of the new PANI asymmetric membranes prepared from hexane are approximately 12 and 4 times higher, respectively, than the values reported previously for the PANI integrally skinned asymmetric membranes (ISAMs) (123 MPa Young's modulus and 1.8 % strain at break). Furthermore, monolithic electrochemical actuators based on a single PANI asymmetric membrane were constructed, and a bending movement of up to 20 Hz was experimentally recorded in a hydrochloric acid aqueous solution. A lifetime of over 329 500 cycles was determined for these actuators at a ± 2° angular displacement (5 Hz). The lifetime is limited by a bending fatigue that creates a transversal crack on the PANI membrane at the air–water interface. Control over the actuator movement is also manifested by the linear dependences of the bending angle on the charge and of the angular velocity on the current. These relationships are independent of both the kind of applied electric signal and the frequency used.