伴随内转换电子发射的俄歇电子能量及强度计算

简要介绍了伴随内转换电子发射产生的俄歇电子能量与强度的计算方法、计算程序及工作流程，并以^129Iβ^-衰变为例说明其具体应用。     

Investigation of the Correlation between Texture and Microstructure on a Submicrometer Scale in the TEM

In recent years the investigation of local texture and microstructure by analysis of electron backscatter diffraction patterns (EBSP) in the SEM has become a very powerful and popular method. With the introduction of SEM with field emission guns (FEG) the spatial resolution of EBSP measurements could be enhanced from 500 nm with a tungsten emitter to better than 50 nm. This evolution of SEM techniques raises the question whether transmission electron microscopy (TEM) still has fields of application in texture research. The present article answers this question with a clear “yes” and presents three examples of investigations where TEM is indispensable. The three examples comprise the investigation of the correlation between dislocation structure and deformation texture, a study on nucleation mechanisms of recrystallization in highly deformed metals and the investigation of microtexture and microstructure in nanocrystalline materials. Together with the presentation of these cases some of the necessary measurement techniques are described briefly. It is shown that TEM has to be applied when highest spatial resolution of orientation determination and imaging and high accuracy of orientation determination are to be reached, when the three‐dimensional and quantitative characterization of lattice defects is required or when materials with a high density of lattice defects are to be investigated.     

Formation reactions of chalcopyrite compounds and the role of sodium doping

The selenisation of the thin film precursors indium, Cu-In and Cu-In-Ga has been studied by in-situ X-ray diffraction. The influence of sodium doping on the kinetics of the solid-state reactions observed agrees with the predictions derived from a phenomenological model presented earlier. In this model a layer of sodium polyselenide is assumed to form at the surface of the precursor, or around each crystal grain. This layer might be responsible for impeded ion exchange in certain solid-state reactions.     

Fabrication and characterization of Cu2ZnSnS4 thin films deposited by spray pyrolysis technique

We have investigated synthesis conditions and some properties of sprayed Cu₂ZnSnS₄ (CZTS) thin films in order to determine the best preparation conditions for the realization of CZTS based photovoltaic solar cells. The thin films are made by means of spraying of aqueous solutions containing copper chloride, zinc chloride, tin chloride and thiourea on heated glass substrates at various temperatures. In order to optimize the synthesis conditions of the CZTS films, two series of experiments are performed. In the first series the sprayed duration was fixed at 30 min and in the second it is fixed at 60 min. In each series, the substrate temperature was changed from 553°K to 633°K. The X-ray diffraction shows, on one hand, that the best crystallinity was obtained for 613°K as substrate temperature and 60 min as sprayed duration. On the other hand, these CZTS films exhibit the kesterite structure with preferential orientation along the [112] direction. Atomical Force Microscopy was used to determine the grain sizes and the roughness of these CZTS thin film. After the annealing treatment, we estimated the optical band-gap energy of the CZTS thin film exhibiting the best crystallinity as 1.5 eV which is quite close to the optimum value for a solar cell.     

Young’s modulus of crystalline C60 nanotubes studied by in situ transmission electron microscopy

Bending tests of crystalline nanotubes composed of fullerene C₆₀ molecules are performed inside a high-resolution transmission electron microscope. We fixed one side of a C₆₀ nanotube with a body-centered tetragonal structure with typical inner and outer diameters, i.e., 180 nm and 510 nm, respectively, and then applied concentrated forces on the other side using piezomanipulation of a silicon nanotip. The bending process was observed in situ by transmission electron microscopy with simultaneous measurements of the forces by an optical deflection method. It was found that the Young’s modulus of the nanotube was estimated to be 62–107 GPa, which was 1.1–3.3 times larger than that of C₆₀ nanowhiskers. The result concerning the increase in the Young’s modulus of the C₆₀ nanotube provided an experimental evidence for the structural model composed of an inner core and a surface shell for C₆₀ nanowhiskers.     

Characterization of supported Pd-Pt catalysts by chemical probes

The temperature programmed (palladium) hydride decomposition appeared very effective method for diagnosing the extent of alloying in Pd-Pt/SiO₂ catalysts. Introduction of Pt to Pd catalysts moves the TPHD peak gradually towards lower temperatures and the shift in hydride decomposition peak is accompanied by a decrease in the amount of released hydrogen. The catalysts prepared the direct redox method showed much better alloy homogeneity than the samples prepared by coimpregnation. The results of probing with other techniques, i.e. catalytic probing with hydrodechlorination of CCl₂F₂ and XRD, were in line with TPHD data. The catalytic probing showed the presence of synergistic effect, a clear indication of Pd-Pt mixing. XRD data of post-reaction samples showed carbon incorporation into Pd-rich phase, whereas separate Pt-rich phase did not experience any bulk carbiding.     

Accelerator Analysis of Tributyltin Adsorbed onto the Surface of a Tributyltin Resistant Marine Pseudoalteromonas sp. Cell

Tributyltin (TBT) released into seawater from ship hulls is a stable marine pollutant and obviously remains in marine environments. We isolated a TBT resistant marine Pseudoalteromonas sp. TBT1 from sediment of a ship’s ballast water. The isolate (10^{9.3 ± 0.2} colony-forming units mL⁻¹) adsorbed TBT in proportion to the concentrations of TBTCl externally added up to 3 mM, where the number of TBT adsorbed by a single cell was estimated to be 10^8.2. The value was reduced to about one-fifth when the lysozyme-treated cells were used. The surface of ethanol treated cells became rough, but the capacity of TBT adsorption was the same as that for native cells. These results indicate that the function of the cell surface, rather than that structure, plays an important role to the adsorption of TBT. The adsorption state of TBT seems to be multi-layer when the number of more than 10^6.8 TBT molecules is adsorbed by a single cell.     

Bruchanalyse an Hohlgläsern

Failure analysis of hollow glasses The failure analysis is very important to clarify damages of hollow glasses. Damages of glass bottle through over pressure are very often linked with damages to persons. This is the reason why the causal research is from particular importance. Different surface characteristics of glass fragments as well as the fracture pattern give hints to the direction of the crack, the stress just before breakage and the reason of stress. A reconstruction of the bottle is a further helpful instrument for cause studies. The difference of the various characteristics of the surface will be explained. Further on there will be discussed different reasons and mechanism of fracture.     

Quantification of the layer dispersion degree in polymer layered silicate nanocomposites by transmission electron microscopy

As the performance of polymer layered silicate nanocomposites strongly depends on their interior layer dispersion, quantification of the layer dispersion degree is needed. In this work, a new methodology was developed to determine the dispersion parameter D_0.1, based on the measurement of the free-path spacing distance between the single clay sheets from the transmission electron microscopy (TEM) images. Several examples of exfoliated, intercalated, and immiscible composites were studied. It was found that the exfoliated composites had D_0.1 over 8%, while that of intercalated composites were between 4 and 8%. In the case of intercalation, a high frequency peak appeared at a short spacing distance in the histogram, which was a characteristic of the intercalation, distinct from the exfoliation. The main utility of this TEM methodology is for the quantification of exfoliated or intercalated samples with small number of layers with stacks. The dispersion parameter D_0.1 below 4% was suggested to classify as immiscible. A unique advantage of the TEM measurement is that the dispersion degree of different fillers can be counted individually.     

Focal adhesion interactions with topographical structures: a novel method for immuno-SEM labelling of focal adhesions in S-phase cells

Current understanding of the mechanisms involved in osseointegration following implantation of a biomaterial has led to adhesion quantification being implemented as an assay of cytocompatibility. Such measurement can be hindered by intra-sample variation owing to morphological changes associated with the cell cycle. Here we report on a new scanning electron microscopical method for the simultaneous immunogold labelling of cellular focal adhesions and S-phase nuclei identified by BrdU incorporation. Prior to labelling, cellular membranes are removed by tritonization and antigens of non-interest blocked by serum incubation. Adhesion plaque–associated vinculin and S-phase nuclei were both separately labelled with a 1.4 nm gold colloid and visualized by subsequent colloid enhancement via silver deposition. This study is specifically concerned with the effects microgroove topographies have on adhesion formation in S-phase osteoblasts. By combining backscattered electron (BSE) imaging with secondary electron (SE) imaging it was possible to visualize S-phase nuclei and the immunogold-labelled adhesion sites in one energy 'plane' and the underlying nanotopography in another. Osteoblast adhesion to these nanotopographies was ascertained by quantification of adhesion complex formation.