A generalized equation for the prediction of melting temperatures of homopolymers and copolymers

A generalized equation was derived to calculate the melting temperatures of homopolymers and copolymers. The Gibbs‐Thomson equation for homopolymers and a modified application to copolymers were derived using the proposed equation. The melting temperature T_m⁰ in the Flory equation corresponds to the melting temperature T_m^C,∞ of copolymer crystals with stems of infinite length. Also, T_m^C,n*, the melting temperature for copolymer crystals with stems containing the maximum possible number of structural units, n*, should be used instead of T_m⁰ as the basis of supercooling in crystallization. The proposed equation shows good agreement with experimental data for α‐alkene‐ethylene homogeneous copolymers.     

Non-steady-state model for kinetics of free radical polymerization, 4. Direct thermal initiation

This paper deals with the non-steady-state kinetics of direct thermal initiated polymerization. The initiation is assumed to be a bimolecular reaction of the monomer. The relationship between the radical concentration and the monomer conversion is rigorously derived. In further treatment a few very close approximations are introduced based on the fact that the number of monomer molecules reacting in the initiation step is much less than that consumed in the propagation step for a process producing high polymer, and the value of the rate constant for propagation or chain transfer is much lower than that for chain termination. Expressions for various molecular parameters, such as molecular weight distribution, number-average and weight-average degrees of polymerization, and dispersity, are given. Several numerical examples are provided.     

分子结构对增塑聚氯乙烯性能的影响

研究了聚合度、分子量分布和支化结构对增塑聚氯乙烯加工流变性能和物理力学性能的影响。结果表明，增塑ＰＶＣ的加工流变性能随聚合度的增加而恶化；拓宽分子量分布和引入支化结构均有利于加工流变性能的提高；增塑ＰＶＣ的拉伸强度随聚合度的增加而提高，而压缩永久变形却随之减小；分子量分布对物理力学性能的影响不大；支化ＰＶＣ的拉伸强度略有下降。     

油溶性减阻功能聚合物的研制

介绍了以混合α-烯烃为原料,制备了具有减阻功能的共聚物。讨论了催化剂浓度、聚合温度、预聚合时间、原料单体中杂质含量对共聚物特性粘度和转化率的影响。试验表明,在较低的催化剂浓度和预聚合温度下,能得到较高分子量的聚合物。气相色谱法和DSC法测定其组成和单体混合物的组成基本一致,表明共聚物是一种无规的梳状结构聚合物。该聚合物达到较高特性粘度时,能获得较好的减阻率。     

A method to estimate entropies and heat capacities applied to alkali oxides

We present a method that is useful in the estimate and assessment of heat capacity data. The approach is based on an analysis of the logarithmic average of the phonon frequencies. In this quantity, that may be easily derived from experimental data on the vibrational entropy, the influence of atomic masses can be exactly accounted for even in polyatomic solids. Our method is applied to Li₂O, Na₂O, K₂O, Rb₂O, and Cs₂O. In particular, literature data for K₂O are critically examined.     

基于小波熵的电容器扰动识别和定位

对投电容器扰动识别和定位的方法进行了改进。针对其他此类方法的不足，比如在电压幅值低时投电容器扰动的识别、定位“可信度不高”等，文中通过提取小波变换的特定层的系数，对需要识别的电容器扰动的分解信号相对增强，而其他扰动的分解信号相对减弱，然后再提取熵特征值，结果表明它可以作为识别低电压时投电容器扰动的依据。在对电容器扰动进行定位时，参考了功率和能量定位法，并对其进行了改进。仿真分析证明，在电压幅值较低时，可以准确和可靠地对电容器扰动进行识别和定位。     

Phase separation studies in RIM polyurethanes catalyst and hard segment crystallinity effects

Polyurethanes were prepared from pure 4,4′-diphenylmethane diisocyanate (MDI), 1,4-butane diol (BDO) or 1,2-ethane diol (EDO) and α,ω-hydroxyl poly(propylene oxide) (PPO) by reaction injection moulding (RIM). Hard segment (MDI + BDO or EDO) level was 45–50 wt%. The PPO had about 20% ethylene oxide copolymerized in at the chain ends to provide 80% primary OH end groups. M_n was varied from 2000 to 4000. Dibutyl tin dilaurate catalyst and mould temperature were varied. Dynamic mechanical, wide-angle X-ray, differential scanning calorimeter, molecular weight and tensile elongation measurements were made on the RIM polyurethanes. At low reaction rates (low catalyst or temperature) highly crystalline, well phase separated but low molecular weight polymers were produced. At high catalyst or temperature levels more poorly phase separated but high molecular weight, tough polymers resulted. Higher M_n PPO gave better phase separation and EDO gave higher melting temperatures. Preventing hard segment crystallinity by substituting asymmetric MDI or glycols resulted in phase compatibility.     

超高分子量聚乙烯衬板在煤仓中的应用

介绍了井底煤仓溜煤斜面采用超高分子量聚乙烯衬板安装及应用情况 ,对井底煤仓棚煤原因及解决办法进行了探讨     

热带城市垃圾典型组分的热解特性研究

对热带城市垃圾的几种典型组分进行了热解实验，得到了它们的失重曲线，通过对失重曲线进行分析，得到了这几种典型组分的热解规律，并通过建立热解动力学模型，求出了其中两种组分的活化能E和频率因子A。     

有扰对称信道平均信息量的计算

照相手机让诺基亚抢了风头，这真是亚洲人的失策。在日本和韩国，内置摄像头的手机早就不是什么值得炫耀的东西了。不过日本人的动作还是很快的，GD88和N8一副后来居上的架势，让人不敢小瞧。