冷拔内螺纹管拉拔力的有限元计算方法

本文基于三维弹塑性大变形有限元分析理论,通过对内螺旋凸筋管冷拔成形过程进行有限元仿真,建立增量步与拉拔力的关系,提出了拉拔力的计算方法.经实验验证,理论计算值与实测值相吻合,可为拉拔模具和工艺参数的设计提供参考.     

Monte-carlo modeling of grain growth in Zr equal channel angular pressed and recrystallized

Grain boundary character distribution in equal-channel-angular pressed Zr was studied. Using a die design of 90°/20° and an operation temperature of 350°C. The initial grain size of 20 μm was reduced to about 270 nm with 4 passes via route B_c. The grain growth kinetics of the recrystallized state was obtained by experiment and Monte-Carlo computer simulation, respectively, which showed good agreement. Based on kinetics and morphological characteristics, it was concluded that the grain coarsening mechanism was governed by normal grain growth. No sign of abnormal grain growth was detected either in the experiment or in simulation despite taking into consideration anisotropy in grain boundary energy as well as its mobility. This indicates that grain boundaries produced by severely deformed Zr are stable against explosive coarsening. The evolution characteristics of the microstructure in the present ECA pressed and recrystallized Zr differed from those of cold rolled Ti in that the grain boundary misorientation distribution and texture were rather stable during grain growth. Jointly Appointed by the Center for Advanced Aerospace Materials This article is based on a presentation made in the 2002 Korea-US symposium on the “Phase Transformations of Nano-Materials,” organized as a special program of the 2002 Annual Meeting of the Korean Institute of Metals and Materials, held at Yonsei University, Seoul, Korea on October 25–26, 2002.     

Drawing of square twisted wire

The shape of the deformation zone during drawing of square twisted wires is described in this paper. The condition of the stable deformation of the wire is formulated. This condition is satisfied by the constant value of the pitch of the helical surface of the die. The work focuses on the investigation of the influence of the die cone angle on the drawing parameters, in particular on the drawing stress.     

Pro/E工程剖视图与制图国标不相符合问题的解决方法

利用Pro/E三维模型与二维图形双向关联功能可以快速生成工程图,但由于在视图表达上有些方面不符合我国制图标准而影响其有效使用.本文针对Pro/E制作工程剖视图时所存在的与制图国标不相符合的问题,提出了解决这些问题的方法和技巧.     

铸钢件铸造工艺CAD软件的研制与应用

在收集、整理和总结多个版本和厂家的参考材料和手册以及作者多年工作经验的基础上 ,在国产CAXA电子图版的二次开发平台上 ,选用VisualC 语言研制了砂型铸钢件铸造工艺CAD软件。该软件具有图库管理、铸件重量和模数计算、铸造工艺方案和参数选择、冒口系统设计和浇注系统设计等项基本功能 ,对下环铸钢件铸造工艺的计算机辅助设计和生产实践结果表明 ,可以缩短工艺设计周期 ,提高工艺设计水平 ,生产优质铸件。     

锦纶66浸胶帘子布生产中的张力与控制

分析了帘子布生产中张力的作用及各区段的张力情况。张力应根据生产品种及浸胶帘子布的内在质量要求来选择，一般张力设定依据为拉伸区张力是干燥区张力的１倍，定型区张力是拉伸区张力的０．６５倍。同时应控制好各区段的温度，降低拉伸应力使锦纶６６帘子布拉伸均匀，提高帘子布的物理性能。     

一步法生产涤纶FDY工艺的探讨

利用ＫＶ７３１纺丝设备一步法生产出涤纶ＦＤＹ，探讨了热辊拉伸和熔体温度对纤维质量的影响。采用高特性粘数的聚酯切片，严格控制纺丝工艺，可以在５０００ｍ／ｍｉｎ的纺丝速度下纺制高质量的细旦涤纶ＦＤＹ。     

Application of CO2 laser heating zone drawing and zone annealing to nylon 6 fibers

Nlon 6 fibers were zone drawn and zone annealed by using a continuous wave carbon dioxide laser to develop their mechanical properties. A laser‐heating zone drawing was carried out under a applied tension of 35.4 MPa at a power density of 9.65 W · cm^?2, and then the zone‐drawn fiber was annealed. A laser‐heating zone annealing was carried out in two steps at a power density of 9.65 W · cm^?2; the first step was carried out under 423 MPa and the second under 517 MPa. The treating temperature of the fiber heated by the CO₂ laser was measured by using an infrared thermographic camera equipped with a magnifying lens. The treating temperature at the zone drawing is 138°C, and those at the first and the second zone annealing are 121 and 125°C, respectively. The second laser‐heated zone‐annealed fiber has a birefringence of 65.2 × 10^?3, a degree of crystallinity of 54%, and a storage modulus of 21 GPa at 25°C. Wide‐angle X‐ray diffraction patterns for the laser‐heated zone‐drawn and the zone‐annealed fibers show (200) reflection and (002/202) doublet due to only an α form on the equator. The laser‐heated zone‐drawn fiber has a melting endotherm peaking at 216°C and a trace of shoulder on the higher temperature side of its peak, and the laser‐heated zone‐annealed fibers have a single melting endotherm peaking at 216°C. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 83: 1711–1716, 2002