纳米蒙脱土/环氧树脂胶粘剂制备工艺优化选择

介绍了制备纳米蒙脱土/环氧树脂胶粘剂的方法,并通过正交试验的方法分析了固化时间、固化温度、搅拌时间、搅拌温度对纳米蒙脱土/环氧树脂胶粘涂层拉伸剪切强度的影响,给出了上述四个工艺参数的最佳工艺规范并通过试验验证了结论。     

保护胶体稳定的丙烯酸酯乳液流变性

分别采用常规乳化剂和羟乙基纤维素为保护胶体制备丙烯酸酯乳液。通过TEM分别观察乳胶粒的形态。利用流变仪测定剪切速率（Ds）-剪切应力（τ）关系、剪切速率（Ds）-黏度（η）关系。结果表明：采用羟乙基纤维素为保护胶体制备的乳液与常规乳液具有不同结构，该结构使其乳液体系流变性能不同。在相同剪切速率下，保护胶体制备的丙烯酸酯乳液的剪切力明显大于常规乳液的剪切力，该乳液在一定剪切速率范围内有剪切稀化现象。     

染料释放化合物及一当量成色剂浅谈

简述了染料释放化合物的发展过程 ,并由此引出一当量成色剂的概念 ,叙述了一当量成色剂应用和发展 ,对一当量成色剂应用前景做了预测。     

Shear rate dependence of viscosity and first normal stress difference of LCP/PET blends at solid and molten states of LCP

The liquid crystalline polymer (LCP) and polyethylene terephthalate (PET) were blended in an elastic melt extruder to make samples having 20, 40, 60, 80, and 100 wt % of LCP. Morphology of these samples was studied using scanning electron microscopy. The steady state shear viscosity (η), dynamic complex viscosity (η*) and first normal stress difference (N₁) were evaluated and compared at two temperatures: 265°C, at which LCP was in solid state, and 285°C, at which LCP was in molten state. The PET was in molten state at both the temperatures. The shear viscosity of the studied blends displayed its dependence on composition and shear rate. A maxima was observed in viscosity versus composition plot corresponding to 80/20 LCP/PET blend. The N₁ increased with LCP loading in PET and with the increased asymmetry of LCP droplets. The N₁ also varied with the shear stress in two stages; the first stage demonstrated elastic deformation, whereas second stage displayed dominant plastic deformation of LCP droplets. © 2007 Wiley Periodicals, Inc. J Appl Polym Sci 104: 2212–2218, 2007     

模数对无机富锌涂料和涂层性能的影响

硅酸钾富锌涂料是目前广泛使用的钢铁防腐蚀涂料。作为涂料粘结剂的高模数硅酸钾溶液对涂料和涂层的性能有重要影响。本研究考察了硅酸钾粘结剂的模数变化对涂料及涂层性能产生的影响。实验结果表明：粘结剂模数的提高可以提高固化后涂层的耐水性能，当粘结剂模数在5.0左右时，所得富锌涂层具有最佳的耐磨性能，但当粘结剂模数超过5.5时会造成涂料施工性能和贮存稳定性下降，涂层柔韧性降低，从而降低涂层的耐磨性能。     

考虑土体强度参数深度依赖性的非平稳随机场边坡滑动深度和体积分析

基于随机有限元方法（RFEM）和Monte-Carlo模拟,建立了能够模拟具有深度依赖性的土体强度参数边坡或具有软弱夹层边坡的非平稳随机场模型。通过辐射扫描方法获取最危险滑动面,得到非平稳随机场边坡滑动深度和滑动体积。将该方法与均质边坡和平稳随机场边坡获得的滑动深度和滑动体积进行对比,研究土体强度参数深度依赖性的非平稳随机场边坡的不同坡度和各向异性对滑动深度和滑动体积的影响。结果表明：基于RFEM的非平稳随机场滑动深度和滑动体积结果为地质灾害风险及后果评估提供了一个参考分析的新角度;参数的深度依赖性程度越高(变化率b越大),则边坡平均滑动深度和滑动体积越小;在大坡度滑坡风险后果评估中,可以基于均质边坡分析结果进行初步预估;在非平稳随机场中,随着各向异性的增大,所有坡度边坡的滑动体积变异系数增大;不同坡度下,水平方向的相关程度越大,则土坡内软弱夹层的不确定性越强,滑动体积的变异系数也不断增大。     

The effect of various slaked limes on the microstructure of a lime-cement-sand mortar

The present work aims to provide a better understanding of the effect of both the proportions and the characteristics of slaked lime on the microstructure of a lime-cement-sand mortar. Cement (CPA CEM I 52.5) has been replaced by various categories of slaked lime chosen for the diversity of their physico-chemical characteristics.Cement has been replaced by lime in proportions varying between 0 to 10% of the total binder mass. With very few exceptions, mortars were produced by maintaining the quantity of water constant.Experimental results show that it is necessary to have a high lime substitution percentage to influence the microstructure of the mortar, except in the case of a lime containing magnesium hydroxide or calcic lime featuring sizeable specific surface area.The influence of the nature of the substituted lime on the development of the microstructure in the matrix has been examined by SEM observations of the mortar micro porosity.     

Application of orthogonal collocations to some transport phenomena problems in co-axial cylinders and spheres

Collocation methods are developed for the solution of some differential equation models for transport phenomena problems in one-and two-dimensions in co-axial annuli of spherical and cylindrical shapes. General formulae are developed to obtain orthogonal polynomials over an arbitrary interval using two types of weighting functions. The convergence and accuracy of the methods are demonstrated using two test problems, i.e., calculation of effectiveness factors in (a) a spherical pellet with peripherally deposited catalyst and (b) a Raschig ring type cylindrical catalyst pellet. Comparisons of results obtained from the present methods with analytic solutions for the first-order reactions indicate good agreement. Numerical solutions are also obtained for the second-and the third-order reactions for which analytic solutions are not available. Results obtained in terms of a new Thiele modulus involving the ratio of volume of peripherally deposited part of catalyst to exterior surface area indicate that this normalization brings effectiveness factor versus Thiele modulus curves close together for co-axial spherical and long cylindrical pellets, as it does for these geometries without the inner co-axial portion.     

Synthesis and characterization of new functional poly(urethane‐imide) crosslinked networks

To synthesize new functional poly(urethane‐imide) crosslinked networks, soluble polyimide from 2,2′‐bis(3,4‐dicarboxyphenyl) hexafluoropropane dianhydride, 4,4′‐oxydianiline, and maleic anhydride and polyurethane prepolymer from polycaprolactone diol, tolylene 2,4‐diisocyanate and hydroxyl ethyl acrylate were prepared. Poly(urethane‐imide) thin films were finally prepared by the reaction between maleimide end‐capped soluble polyimide (PI) and acrylate end‐capped polyurethane (PU). The effect of polyurethane content on dielectric constant, residual stress, morphology, thermal property, and mechanical property was studied by FTIR, prism coupler, Thin Film Stress Analyzer (TFSA), XRD, TGA, DMTA, and Nano‐indentation. Dielectric constant of poly(urethane‐imide) thin films (2.39–2.45) was lower than that of pure polyimide (2.46). Especially, poly(urethane‐imide) thin films with 50% of PU showed lower dielectric constant than other poly(urethane‐imide) thin films did. Lower residual stress and slope in cooling curve were achieved in higher PU content. Compared to typical polyurethane, poly(urethane‐imide) thin films exhibited better thermal stability due to the presence of the imide groups. The glass transition temperature, modulus, and hardness decreased with increase in the flexible PU content even though elongation and thermal expansion coefficient increased. Finally, poly(urethane‐imide) thin films with low residual stress and dielectric constant, which are strongly affected by the morphological structure, chain mobility, and modulus, can be suggested to apply for electronic devices by variation of PU. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 100: 113–123, 2006     

多孔介质内部热质传递的等效耦合扩散模型的推导及其应用

基于Whitaker的体积平均方程，在不附加任何新的假设的基础上，对多孔介质内部热质传递的等效耦合扩散模型进行推导，得出了多孔介质内部热质传递的等效耦合扩散模型。并应用该模型对瓷质砖体干燥过程进行了数值模拟，模拟结果与实验结果十分吻合。