A new numerical algorithm to check the observability and bad-data processing ability of the metering scheme

This paper provides a unified approach for the optimization of measurements placements employed for power system online monitoring through state estimation. The proposed methodology, which can be suitable for the mixed measure system, preserves state estimation observability and bad-data processing capability by employing numerical algorithms for observability checking, critical measurements and critical couple identification. First, node injection radix measurements and measurement categories are defined. According to the above definitions, the coefficient matrix can be solved. The analysis on the column vectors of the coefficient matrix can determine each measurement classification. Furthermore, the numbers of each measurement class contains can determine bad-data processing capability. The observability can be checked by the type number of measurements. The proposed method is illustrated with the IEEE39-bus system and the IEEE118-bus system. Results from the case studies are presented to demonstrate that the approach adequately fulfills the desired properties related to observability, bad-data processing, cost, and robustness.     

On the performance of improved quadrature spatial modulation

Quadrature spatial modulation (QSM) utilizes the in‐phase and quadrature spatial dimensions to transmit the real and imaginary parts of a single signal symbol, respectively. The improved QSM (IQSM) transmits two signal symbols per channel use through a combination of two antennas for each of the real and imaginary parts. The main contributions of this study can be summarized as follows. First, we derive an upper bound for the error performance of the IQSM. We then design constellation sets that minimize the error performance of the IQSM for several system configurations. Second, we propose a double QSM (DQSM) that transmits the real and imaginary parts of two signal symbols through any available transmit antennas. Finally, we propose a parallel IQSM (PIQSM) that splits the antenna set into equal subsets and performs IQSM within each subset using the same two signal symbols. Simulation results demonstrate that the proposed constellations significantly outperform conventional constellations. Additionally, DQSM and PIQSM provide a performance similar to that of IQSM while requiring a smaller number of transmit antennas and outperform IQSM with the same number of transmit antennas.     

A distributed state estimation method for power systems incorporating linear and nonlinear models

High-voltage transmission networks are commonly equipped with phasor measurement units (PMU), and some of them are PMU observable. However, PMUs are seldom installed in distribution networks due to budget limitations. The state estimation equations of PMU observable areas are linear, while those of other areas remain nonlinear. This paper proposes a new distributed state estimation method for solving multi-area state estimation problems, in which linear models are used for high-voltage transmission network, while nonlinear models are adopted for other areas. In PMU observable area, we select coordinating variables as generalized cost functions which accurately represent the sensitivity between the linear SE objective function and boundary states. Consequently, SE results identical to a centralized estimator can be obtained without iterations at the coordination level. This paper presents the problem model and theoretical analysis of the proposed method, and shows its effectiveness by numerical tests.     

A stiffness parameter and truncation error criterion for adaptive path following in structural mechanics

We explore a truncation error criterion to steer adaptive step length refinement and coarsening in incremental-iterative path following procedures, applied to problems in large-deformation structural mechanics. Elaborating on ideas proposed by Bergan and collaborators in the 1970s, we first describe an easily computable scalar stiffness parameter whose sign and rate of change provide reliable information on the local behavior and complexity of the equilibrium path. We then derive a simple scaling law that adaptively adjusts the length of the next step based on the rate of change of the stiffness parameter at previous points on the path. We show that this scaling is equivalent to keeping a local truncation error constant in each step. We demonstrate with numerical examples that our adaptive method follows a path with a significantly reduced number of points compared to an analysis with uniform step length of the same fidelity level. A comparison with Abaqus illustrates that the truncation error criterion effectively concentrates points around the smallest-scale features of the path, which is generally not possible with automatic incrementation solely based on local convergence properties.     

A Global Maximum Error Controller Based Nonlinearity Aware TPWL Method for Reducing Nonlinear Systems

Abstract

Model order reduction is a common practice to reduce large order systems so that their simulation and control become easy. Nonlinearity aware trajectory piecewise linear is a variation of trajectory piecewise linearization technique of order reduction that is used to reduce nonlinear systems. With this scheme, the reduced approximation of the system is generated by weighted sum of the linearized and reduced sub-models obtained at certain linearization points on the system trajectory. This scheme uses dynamically inspired weight assignment that makes the approximation nonlinearity aware. Just as weight assignment, the process of linearization points selection is also important for generating faithful approximations. This article uses a global maximum error controller based linearization points selection scheme according to which a state is chosen as a linearization point if the error between a current reduced model and the full order nonlinear system reaches a maximum value. A combination that not only selects linearization points based on an error controller but also assigns dynamic inspired weights is shown in this article. The proposed scheme generates approximations with higher accuracies. This is demonstrated by applying the proposed method to some benchmark nonlinear circuits including RC ladder network and inverter chain circuit and comparing the results with the conventional schemes.     

Anti‐Sway Crane Control Considering Wind Disturbance and Container Mass

A method for estimating the sway angle using an observer has already been proposed. The state observer estimates the sway angle accurately and must use the detected sway angle value. However, the estimated sway angle has an error owing to rope length error, friction force, and wind. Moreover, the container mass cannot be determined, and therefore the observer parameter is not suitable. We already proposed robust antisway control for overcoming rope length error without adding a new sensor. Further, we designed a friction disturbance observer to cancel out the influence of the friction force. In this paper, we first propose a container mass estimation method when a crane system performs rolling up control. The observer parameter can be selected using the estimated mass value. Second, in crane parallel shift control, we propose a robust antisway control even when there is a wind disturbance. We design a wind disturbance observer and propose a wind disturbance estimator to separate the friction observer output from the wind disturbance observer output. We confirm through experiments that the proposed method can reduce vibration.     

A lightweight autonomous MAV for indoor search and rescue

Micro Aerial Vehicles (MAVs) have great potentials to be applied for indoor search and rescue missions. In this paper, we propose a modular lightweight design of an autonomous MAV with integrated hardware and software. The MAV is equipped with the 2D laser scanner, camera, mission computer and flight controller, running all the computation onboard in real time. The onboard perception system includes a laser‐based SLAM module and a custom‐designed visual detection module. A dual Kalman filter design provides robust state estimation by multiple sensor fusion. Specifically, the fusion module provides robust altitude measurement in the circumstance of surface changing. In addition, indoor‐outdoor transition is explicitly handled by the fusion module. In order to efficiently navigate through obstacles and adapt to multiple tasks, a task tree‐based mission planning method is seamlessly integrated with path planning and control modules. The MAV is capable of searching and rescuing victims from unknown indoor environments effectively. It was validated by our award‐winning performance at the 2017 International Micro Air Vehicle Competition (IMAV 2017), held in Toulouse, France. The performance video is available on https://youtu.be/8H19ppS_VXM .     

Nonuniform linear array DOA estimation using EM criterion

In this letter, we address the problem of Direction of Arrival (DOA) estimation with nonuniform linear array in the context of sparse Bayesian learning (SBL) framework. The nonuniform array output is deemed as an incomplete-data observation, and a hypothetical uniform linear array output is treated as an unavailable complete-data observation. Then the Expectation-Maximization (EM) criterion is directly utilized to iteratively maximize the expected value of the complete-data log likelihood under the posterior distribution of the latent variable. The novelties of the proposed method lie in its capability of interpolating the actual received data to a virtual uniform linear array, therefore extending the achievable array aperture. Simulation results manifests the superiority of the proposed method over off-the-shelf algorithms, specially on circumstances such as low SNR, insufficient snapshots, and spatially adjacent sources.     

基于分段加权的反向稀疏跟踪算法研究

为提高稀疏表示跟踪模型性能，提出一种分段加权的反向稀疏跟踪算法，将跟踪问题转化为在贝叶斯框架下寻找概率最高的候选对象问题，构造不同的分段权重函数来分别度量候选目标与正负模板的判别特征系数。通过池化来降低跟踪结果的不确定性干扰，选择正负模板加权系数差值最大的候选表示作为跟踪结果。实验表明，在光照变化、遮挡、快速运动、运动模糊情况下，所提出的算法可以确保跟踪结果的准确性和鲁棒性。     

Mixture ratio modeling of dynamic systems

Any knowledge extraction relies (possibly implicitly) on a hypothesis about the modelled-data dependence. The extracted knowledge ultimately serves to a decision-making (DM). DM always faces uncertainty and this makes probabilistic modelling adequate. The inspected black-box modeling deals with “universal” approximators of the relevant probabilistic model. Finite mixtures with components in the exponential family are often exploited. Their attractiveness stems from their flexibility, the cluster interpretability of components and the existence of algorithms for processing high-dimensional data streams. They are even used in dynamic cases with mutually dependent data records while regression and auto-regression mixture components serve to the dependence modeling. These dynamic models, however, mostly assume data-independent component weights, that is, memoryless transitions between dynamic mixture components. Such mixtures are not universal approximators of dynamic probabilistic models. Formally, this follows from the fact that the set of finite probabilistic mixtures is not closed with respect to the conditioning, which is the key estimation and predictive operation. The paper overcomes this drawback by using ratios of finite mixtures as universally approximating dynamic parametric models. The paper motivates them, elaborates their approximate Bayesian recursive estimation and reveals their application potential.