污泥热干燥粘结的特征和影响因素

污泥热干燥过程中在干燥设备内部表面的粘结是影响干燥设备性能的重要因素。通过热干燥模拟实验,分析了污泥含水率、加热温度、加热方式、加热界面性质等因素对污泥粘结的影响。结果表明,含水率是影响污泥粘结最主要的因素,污泥含水率较高时,粘结量较少,随着污泥干燥程度增加,含水率降低,粘结量逐渐增加,当含水率达到60%左右时粘结量达到最大,之后转而减少;加热温度不超过120℃时,温度对污泥粘结的影响不明显,加热温度高于120℃时,污泥粘结量随温度升高而显著增加;传导加热方式比对流加热方式更易导致污泥粘结;加热接触界面的表面粗糙度越大则污泥粘结量越大。     

Properties and mechanism of red mud in preparation of ultra-lightweight sludge-red mud ceramics

New ultra-lightweight sludge-red mud ceramics (ULS-RMC) were prepared by red mud (RM), clay and dried sewage sludge (DSS). The properties and mechanism of RM in the preparation of ULS-RMC were discussed. The chemical components, thermal properties and mineral phases of RM were determined by energy dispersive X-ray (EDX), differential scanning calorimetry/thermal gravimetric analysis (DSC/TGA) and X-ray diffraction (XRD), respectively. Constant dosage of DSS to clay and different amounts of RM were utilized in the preparation of ULS-RMC. Physical properties test (bulk density, grain density, water absorption and expansion ratio), XRD and scanning electron microscopy (SEM) were employed to characterize the ULS-RMC. The results show that RM exhibits high hydroscopic property and good water-retention property, and bloating property and fluxing property of RM are caused by abound of gaseous components and flux, respectively. The two chemical properties are utilized to discuss the mineral phases and microstructures differences between ULSC and ULS-RMC.     

好氧颗粒污泥脱氮除磷效率研究

以实验室模拟废水为进水,在SBR反应器中利用好氧颗粒污泥进行N、P的去除效率研究.研究表明:在运行周期约为4h,进水COD控制在500～1200 mg/L之间,室温条件下,好氧颗粒污泥对COD、氨氮、硝氮、TP的去除率稳定维持在97％、95％、92％、86％,说明好氧颗粒污泥特有的结构特性和生物特性有利于脱氮除磷.     

浸提时间对城市污泥重金属浸出特性的影响

在研究含工业废水污泥中Zn、Cu、Pb、Cr、Mn、Ni含量的基础上,应用固体废物浸出毒性方法,以不同浸出时间对污泥中重金属的浸出特性进行了实验研究.结果表明:污泥中Mn和Zn含量较高,其次为Cu和Ni,而毒性较大的Pb和Cr含量较低.浸提时间对污泥中重金属的浸出具有重要影响,污泥中的Zn、Cu、Ni最大浸出浓度在8h时,而Fe和Mn随着浸提时间增加而增加;浸提时间对污泥中重金属浸出量的影响因该重金属的化学性质不同而存在较明显的差别,这可能与浸提过程中的吸附-解吸过程、络合-解离过程和溶解-沉淀/共沉淀等因素有关.     

Extended activated sludge model no. 1 (ASM1) for simulating biodegradation process using bacterial technology

Phosphorus is one of the most important nutrients required to support various kinds of biodegradation processes. As this particular nutrient is not included in the activated sludge model no. 1 (ASM1), this study extended this model in order to determine the fate of phosphorus during the biodegradation processes. When some of the kinetics parameters are modified using observed data from the restoration project of the Xuxi River in Wuxi City, China, from August 25 to 31 in 2009, the extended model shows excellent results. In order to obtain optimum values of coefficients of nitrogen and phosphorus, the mass fraction method was used to ensure that the final results were reasonable and practically relevant. The temporal distribution of the data calculated with the extended ASM1 approximates that of the observed data.     

Performance of Sewage Sludge Treatment and Electricity Generation by Different Configuration Microbial Fuel Cells

This paper compared the degradation efficiency of sludge organic matters and electric-production by two typical microbial fuel cells——dual-chamber microbial fuel cell(DMFC)and single chamber air cathode microbial fuel cell(SAMFC),and the variations of sludge protein,polysaccharide and ammonia nitrogen within the systems were also investigated.The results showed that the concentration of sludge soluble chemical oxygen demand,protein and carbohydrate of DMFC are higher than these of SAMFC during the systems operation,while DMFC can achieve a better ammonia nitrogen removal than SAMFC.Under the same operation condition,the stable voltage output of DMFC and SAMFC is 0.61 V and 0.37 V;the maximum power density of DMFC and SAMFC is 2.79 W/m3and 1.25 W/m3;TCOD removal efficiency of DMFC and SAMFC is 34.14%and 28.63%for 12 d,respectively.Meanwhile,DMFC has a higher coulomb efficiency than SAMFC,but both are less than5%.The results showed that DMFC present a better performance on sludge degradation and electric-production.     

Recycle of valuable products from oily cold rolling mill sludge

Oily cold rolling mill （CRM） sludge contains lots of iron and alloying elements along with plenty of hazardous organic components, which makes it as an attractive secondary source and an environmental contaminant at the same time. The compound methods of ＂vacuum distillation ＋ oxidizing roasting＂ and ＂vacuum distillation ＋ hydrogen reduction＂ were employed for the recycle of oily cold rolling mill sludge. First, the sludge was dynamically vacuum distilled in a rotating furnace at 50 r/rain and 600℃ for 3 h, which removed almost hazardous organic components, obtaining 89.2wt% ferrous resultant. Then, high purity ferric oxide powders （99.2wt%） and reduced iron powders （98.9wt%） were obtained when the distillation residues were oxidized and reduced, respectively. The distillation oil can be used for fuel or chemical feedstock, and the distillation gases can be collected and reused as a fuel.     

线性代数的“可视化”教学

通过Matlab软件的绘图功能将线性代数中三元线性方程组的解和二阶方阵的特征向量可视化,通过"多余"来直观地理解向量组的线性相关性定理,实现了将线性代数部分概念和定理的"可视化".     

Feasibility analysis of high excess pressure cockpit using material substitution based on strain energy

The design concept of high excess pressure cockpit has been proposed as a solution to solve the ergonomics problems caused by cockpit environment.To address the contradiction among mass,economy,maneuverability and environment ergonomics,considering the composite advantages of high strength and lightweight,the feasibility analysis concept of high excess pressure cockpit based on material substitution is proposed in the paper.Based on the strain energy analysis on finite element model,the iteration design method of equal stiffness and lightening effect analysis on material substitution are presented,The weight reduction effect after material substitution can be evaluated intuitively by using equal stiffness curve.The calculation result of cockpit indicates that the lightening effect can reach 35.09%.Because of the complexity of cockpit design,bi-level optimization method is proposed and performed by means of the First-Order Radio algorithm.The research shows that the method can achieve good result.The feasibility of high excess pressure cockpit is studied from the aspect of the relationship between excess pressure and mass,and the research demonstrates that,due to the utilization of T300/4211 in place of 6061 alloy,the excess pressure of cockpit increases from 35 to 45 kPa,a 28.57%increase,while the cockpit mass is decreased by 12.56%.Thus,the contradiction among mass,economy and environment ergonomics can be coordinated,which can provide a reference for the design of high excess pressure cockpit.     

基于城市污水好氧颗粒污泥脱氮除磷系统种群多样性研究

采用16S rDNA克隆文库方法对城市污水脱氮除磷好氧颗粒污泥的细菌种群进行了多样性研究.从16SrDNA克隆文库中随机挑选110个克隆子测序并进行了BLAST比对.结果表明:好氧颗粒污泥序批式反应器(GSBR)系统中细菌群落具有高度多样性,包含14个类群,优势细菌类群为Proteobacteria类群(变形菌类群),占85.18%;细菌类群优势顺序为β-Proteobacteria、α-Proteobacteria、γ-Proteobacteria、uncultured Bacteroidetes、Candidatedivision TM7、δ-proteobacterium、Firmicutes、Planctomycetacia、Actinobacteria、Sphingobacteria、Flavobacteria、Cytophagia、Uncultured bacterium和Uncultured anaerobic bacterium.初步分析了不同细菌类群在脱氮除磷系统中的作用,其中,Proteobacteria纲中部分为聚磷菌,Acidovorax sp.、Planctomycetacia、Cytophagia、Flavobacteria对氮的脱除均有一定作用.