高压对气井套管接头螺纹接触应力的影响研究

高温高压气井对螺纹密封性的要求要比油井更为严格。对于高压气井中的整个管柱,每一段处于不同的力学环境中,发生泄漏的可能性也不同,因此研究压力对气井套管接头螺纹接触应力的影响,对高压气井套管的合理使用尤为重要。利用弹塑性有限元分析方法,建立了API偏梯型螺纹套管接头的有限元模型,分析了气井压力对套管接头接触应力的影响,提供了研究压力对套管接头螺纹接触应力影响的方法。对于井口压力或井底压力超过34MPa的高压气井,应选用气密性良好的特殊螺纹接头,建议采用金属对金属的螺纹接头套管,以加强螺纹部位的连接强度和密封性能。     

低密度微泡沫压井液的研究与应用

吐哈油田部分区块地层压力系数小于0.9,常规水基压井液对储层伤害大,若使用油基压井液成本高,环境污染严重。通过实验优选出了一种低密度水基微泡沫压井液。该压井液具有密度低、泡沫强度高、稳定性好、携砂能力强等优点。现场应用表明,低密度微泡沫压井液稳定时间大于48 h,密度在0.70~0.99 g/cm3之间可调,抗油污染能力强,抗油大于8%,抗温在100℃以上,岩心污染后渗透率恢复值大于80%;并且施工方便,成本低,具有储层保护能力,使用微泡沫压井液的井表皮系数在0.20~2.34之间。     

高坝通航技术在水口工程的新发展

水口水电站坝高101m,航运过坝采用一线三级船闸和一线垂直升船机。水口升船机是当时国内已建和在建同类升船机中总体规模最大的升船机,也是我国第一座自行设计、制造、施工和安装的大型升船机。在塔楼结构动力分析和试验研究、塔楼滑框倒模施工、升船机整体模型试验研究、承船厢整体制造和浮运、船厢安全锁定装置和船厢对接密封装置试验研究、整机安装及联调试验等方面充分体现了水口升船机的建成是高坝通航技术的新发展。     

三峡三期工程主坝大体积混凝土内部温度控制

三峡右岸三期工程施工中,为了有效控制坝体大体积混凝土内部温升,采取了高温季节使用预冷混凝土浇筑、控制混凝土出机口温度及浇筑温度、对混凝土内部人工通水进行初冷、中冷和后冷等措施。三峡三期工程大坝混凝土内部温度没有出现超标现象,混凝土温控工作取得了良好的效果。     

一种零电压转换有源功率因数校正电路的研究

提出了一种基于UC3854的零电压转换有源功率因数校正(ZVT-APFC)的控制电路实现方案,介绍了ZVT电路工作原理,着重分析了由分立元件构成的辅助开关管的驱动电路,通过实验证实了驱动电路的稳定性和可靠性,并通过效率比较验证了ZVT-APFC电路的优良性能。与采用UC3855的电路相比,该电路方案具有简单、可靠、成本低等优点。     

300km/h高速铁路PC槽型梁动力试验研究

介绍北方交通大学与比利时鲁汶大学、布鲁塞尔自由大学、比利时铁路公司合作,在巴黎至布鲁塞尔之间高速铁路线上的Antoing大桥进行的二次高速铁路桥梁动力试验。试验桥梁由跨度50m的多跨预应力混凝土简支槽型梁构成,试验中列车速度达265-310km/h。通过现场试验和实验结果分析,得到了桥梁的频率、振型、阻尼等自振特性,以及桥梁在高速列车作用下的动挠度、梁和桥墩的横向和竖向加速度、橡胶支座的相对位移、梁体的动应变等动力响应特性。试验经验和测试结果对于充实高速铁路桥梁动力分析理论、改进数值分析模型、验证计算结果、提高高速铁路桥梁的动力设计水平、保证行车安全,具有重要的意义。     

Chemische Zusammensetzung und Mikrostruktur polymerabgeleiteter Gläser und Keramiken im System Si–C–O. Teil 2: Charakterisierung der Gefügeausbildung mittels hochauflösender Durchstrahlungselektronenmikroskopie und Feinbereichsbeugung

Chemical Composition and Microstructure of Polymer‐Derived Glasses and Ceramics in the Si–C–O System. Part 2: Characterization of microstructure formation by means of high‐resolution transmission electron microscopy and selected area diffraction Liquid or solid silicone resins represent the economically most interesting class of organic precursors for the pyrolytic production of glass and ceramics materials on silicon basis. As dense, dimensionally stable components can be cost‐effectively achieved by admixing reactive filler powders, chemical composition and microstructure development of the polymer‐derived residues must be exactly known during thermal decomposition. Thus, in the present work, glasses and ceramics produced by pyrolysis of the model precursor polymethylsiloxane at temperatures from 525 to 1550 °C are investigated. In part 1, by means of analytical electron microscopy, the bonding state of silicon was determined on a nanometre scale and the phase separation of the metastable Si–C–O matrix into SiO₂, C and SiC was proved. The in‐situ crystallization could be considerably accelerated by adding fine‐grained powder of inert fillers, such as Al₂O₃ or SiC, which permits effective process control. In part 2, the microstructure is characterized by high‐resolution transmission electron microscopy and selected area diffraction. Turbostratic carbon and cubic β‐SiC precipitate as crystallization products. Theses phases are embedded in an amorphous matrix. Inert fillers reduce the crystallization temperature by several hundred °C. In this case, the polymer‐derived Si–C–O material acts as a binding agent between the powder particles. Reaction layer formation does not occur. On the investigated pyrolysis conditions, no crystallization of SiO₂ was observed.     

激光熔覆专用铁基合金粉末的研究进展

指出了目前防止熔覆层开裂所采取的主要措施中存在的问题,阐述了激光熔覆和热喷涂对于所用合金粉末性能要求之异同,评述了激光熔覆专用铁基合金粉末的研制现状,提出了成分与组织设计的新思想。     

Fatigue limit evaluation of notches,small cracks and defects: an engineering approach

In this paper, the average stress method for the fatigue limit evaluation of stress raising geometrical features is revised and extended. In particular, an analytical close‐form approach was used and the linear elastic stress equations were modified by taking into account the effect of nominal stress on the local stress distribution. Hence, the average tangential stress was correctly evaluated over a distance of 2a₀, where a₀ was El Haddad's short crack constant, for long and small notches as well as for crack‐like notches. When this model is applied to a wide range of geometrical features subjected to mode I fatigue loading, the classical shape of the curves of the Kitagawa–Takahashi diagram was obtained for changes in crack‐like notch size. Similarly, notch sensitivity was estimated by reducing the notch tip radius. The accuracy of the proposed method in predicting fatigue limits was then checked by using experimental data taken from the literature and generated on testing specimens weakened by rounded and sharp notches as well as by small artificial defects.     

二氧化锡溅射工艺研究

SnO2 是最早使用也是目前使用最广泛的一种气敏材料 ,使用该材料设计制作的气敏传感器具有许多优点。在简要介绍溅射镀膜的成膜过程和特点的基础上 ,着重介绍了SnO2 膜的制备流程 ,分析了功率和温度变化对成膜质量的影响