潜油电泵易损零部件失效分析方法

通过对大庆油田近5 a潜油电泵易损零部件的数据统计,应用可靠性分析理论和方法研究了易损零部件的失效规律,得出4大部件的故障率占整个机组系统的91.7%,其可靠度由小到大的次序为电机、保护器、电泵和分离器。在这4大部件中,可靠度较低的零件主要有泵轴、叶导轮、扶正轴承、胶囊和保护器轴,其中泵轴、叶导轮、扶正轴承的主要失效模式是磨损,连接螺栓的主要失效模式是断裂失效。     

宝浪油田宝北区块套管失效机理研究

为了深化宝浪油田的套损机理研究．提出了套管损坏因素新的分类方法。根据该新分类法,研究了宝北区块的套损机理。研究结果揭示了套损井的分布区域在主力油藏区域和主力油层;在构造顶部区域和油层顶部层段;为边缘注水井;集中在强度较低,变形量较大的煤层段和泥岩层段;在储层强度较低的射孔段。这些规律可以用有限元分析和实验结果合理地解释。     

低渗透油田套管损坏机理分析及防治措施

在注水开发油田,油水井套管损坏是一种极为普遍的现象,但又各具特点.通过对鄯善油田套管损坏井的自身特点进行统计、归纳,深入分析低渗透砂岩油藏套管变形影响因素和作用机理,提出了套管损坏井的预防及相应治理措施.     

乙烯装置失效模式分析及基于风险的检验

简述了乙烯装置的工艺流程,分析了装置中常见的几种失效模式及其分布;以乙烯裂解装置为例,简述了RBI的执行过程和结果,从基于风险的检验理念,对制订设备检验策略提出了几点建议。     

Uncertainty of Predictions of Embankment Dam Breach Parameters

Risk assessment studies considering the failure of embankment dams often require the prediction of basic geometric and temporal parameters of a breach, or the estimation of peak breach outflows. Many of the relations most commonly used to make these predictions were developed from statistical analyses of data collected from historic dam failures. The prediction uncertainties of these methods are widely recognized to be very large, but have never been specifically quantified. This paper presents an analysis of the uncertainty of many of these breach parameter and peak flow prediction methods. Application of the methods and the uncertainty analysis are illustrated through a case study of a risk assessment recently performed by the Bureau of Reclamation for a large embankment dam in North Dakota.     

Structural integrity in electronics

With continuing miniaturisation, increased performance demands and the requirement to remove lead from solder alloys, the challenges to structural integrity and reliability of electronic equipment are substantial and increasing. This paper outlines typical features in electronic equipment of which the structural integrity community may be generally unaware. Potential failure modes in service are described, and the problems of scale and material characteristics are considered. Progress in the application of fracture mechanics to the life prediction of interconnections is reviewed. The limited evidence available suggests that the crack growth resistance of silver‐containing lead‐free solders is superior to that of the traditional Sn‐37Pb under cycle‐controlled conditions but there is no difference when time‐dependent conditions prevail. In several respects, it is contended that the electronics sector is faced with challenges at least equivalent to those encountered in gas turbines and nuclear power generation.     

Tensile fracture and failure behavior of technical flax fibers

The apparent tensile strength of technical flax fibers was determined in single‐fiber tests at various clamping lengths (20, 40, and 80 mm) and the outcome was compared with literature data. It was demonstrated that the strength of flax at each clamping length obeyed the two‐parameter Weibull model. The failure mode and sequence were studied in situ (i.e., during loading) by SEM and acoustic emission (AE). The failure sequence (axial splitting of the technical fiber along its elementary constituents, radial cracking of the elementary fibers, multiple fracture of the elementary fibers) concluded reflected the hierarchical build‐up of the flax bast fibers. To the above failure events AE amplitude ranges were assigned. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3638–3645, 2003     

Stress Heterogeneity Effect on the Strength of Silicon Nitride

The experiments reported in this paper demonstrate the causes of the failure of monolithic ceramics. The specimens are made of silicon nitride and tested at room temperature. The stress field within the specimen is different for each of four series of tests that have been conducted. Fractographic observations have also been made to identify the causes of the failures. A size effect analysis is performed.     

Possibilities and extension of XRD material response analysis in failure research for the advanced evaluation of the damage level of Hertzian loaded components

Due to clearly distinguishable damage symptoms, it is differentiated between the surface and sub‐surface failure mode of rolling bearings. Material states red out by X‐ray diffraction (XRD) residual stress measurements point to a variety of loading conditions especially at raceway surfaces that are associated with several competing failure mechanisms. The corresponding lifetime reduction can range from the lower fatigue strength region to material ratcheting in extreme cases. Relevant position of the microstructural changes and nature of the failure mechanisms are characterized. The time alteration of the XRD material parameters measured at or near the surface and at the depth of the maximum equivalent stress correlates, in a different manner, with the statistical parameter of the 10 % bearing life. Both failure modes are illustrated by concrete examples. Contaminated lubricant and boundary lubrication, which represent practically important surface‐induced failures, are discussed in more detail. Gray staining, i.e. shallow pitting, often occurs without distinct indication of global material aging by means of XRD characteristics. Here, scanning electron microscopy observations and electron microprobe analyses point to corrosion fatigue as acting surface failure mechanism. The interaction between material and lubricant under complex loading regimes particularly of mixed friction and corrosion opens further failure research areas in the field of tribology.     

Evaluation of Slow Crack Growth Resistance in Ceramics for High-Temperature Applications

The slow (subcritical) crack growth (SCG) resistance of Si₃N₄ and SiC ceramics has been evaluated by a stepwise loading test on bending bars precracked by Vickers indentation. Three highly refractory materials were selected for the evaluation: i.e., (1) high-purity Si₃N₄ sintered by hot isostatic pressing (HIP) without additives and (2,3) α - and β - SiC pressureless sintered with B and C addition. Under the hypothesis of linear elastic behavior at high temperature, which was found satisfied in the present materials, the SCG resistance was expressed in terms of initial stress intensity factor critical for SCG failure within a predetermined lifetime. The present method was found useful in shortening the testing time and consistent with other traditional fatigue tests (e.g., static-fatigue test): It is recommended as a screening test for materials under research and development. Among the materials tested in the present study, the highest SCG resistance up to 1440°C was found in the high-purity Si₃N₄ without additives.