Corrosion fatigue short crack growth behaviour in a high strength steel

The influence of an aggressive environment (0.6 M, aerated NaCl solution) on short fatigue crack initiation and growth behaviour has been studied. The study involved three major test series, namely: air fatigue, corrosion fatigue, and intermittent air fatigue/corrosion fatigue. The above tests carried out under fully reversed torsional loading conditions at a frequency of 5 Hz, showed that it was the non-metallic inclusions which took part in crack initiation resulting from debonding at metal matrix/inclusion interface and pitting of inclusions in both air and corrosove environments, respectively. Short fatigue crack growth results in these two environments obtained by using plastic replication technique, indicated a large effect of microstructure i.e. prior austenite grain boundaries. The stage/stages at which the environmental contribution was dominant has been discussed by considering the results achieved from intermittent tests. However, the mechanisms involved in corrosion fatigue short crack growth have also been described in the light of results obtained from futher investigations carried out by conducting corrosion fatigue tests under applied cathodic potential conditions and tests on hydrogen pre-charged specimens under air fatigue and uniaxial tension conditions.     

指纹细节特征提取与剪枝

指纹图像经预处理后，由于各种原因，会产生数以百计的特征。为了图像匹配的精确和快速，提出一套在细化后的指纹点线图上提取细节特征并对其剪枝的方法，并根据细节特征的拓扑特性，设计了验证其可靠性的算法。通过实验，证明了该后处理过程在去除指纹图像伪特征方法面具有良好的效果。     

Failure analysis of a wire rope

Wire ropes, pulleys, counterweights, and connecting systems are used for auto tensioning of contact wires of electric railways. A wire rope in one such auto tensioning system suffered premature failure. Failure investigation revealed fatigue cracks initiating at nonmetallic inclusions near the surface of individual wire strands in the rope. The inclusions were identified as Al-Ca-Ti silicates in a large number of stringers, and some oxide and nitride inclusions were also found. The wire used in the rope did not conform to the composition specified for AISI 316 grade steel, nor did it satisfy the minimum tensile strength requirements. Failure of the wire rope was found to be due to fatigue; however, the ultimate fracture of the rope was the result of overload that occurred after fatigue failure had reduced the number of wire strands supporting the load.     

地震资料精细处理和解释在徐家围子油田的应用

以地震资料精细处理和解释在大庆长垣外围徐家围子油田开发中的成功应用为例，论述了地震地质综合描述技术在地质情况复杂的低、特低渗透油田开发中的应用效果。     

结构陶瓷的高温疲劳强度衰减理论

提出了陶瓷材料疲劳强度衰减理论并由此导出了各种疲劳关系式。建立了疲劳基本方程ｄσ＿ｒ／ｄ＿ｉ＝一Ａσ（ｔ）￣ｎｔ￣（－ｍ），得出了疲劳寿命公式Ｔ＝Ｍ（σ＿０－σ）／Ａσ￣ｎ（静疲劳时Ｍ＝１，连续增载疲劳时Ｍ＝ｎ＋１，循环疲劳时Ｍ＝（ｎ＋１）／（１＋Ｒ＋Ｒ￣２＋……＋Ｒ￣ｎ），逐级加载时，并导出不同疲劳方式下疲劳寿命间的关系。同时，用多种Ｓｉ＿３Ｎ＿４材料在高温中作了论证试验，结果与理论一致。     

A pattern recognition-based approach for phylogenetic network construction with constrained recombination

The tree representation of evolutionary relationship oversimplifies the view of the process of evolution as it cannot take into account the events such as horizontal gene transfer, hybridization, homoplasy and genetic recombination. Several algorithms exist for constructing phylogenetic networks which result from events such as horizontal gene transfer, hybridization and homoplasy. Very little work has been published on the algorithmic detail of phylogenetic networks with constrained recombination. The problem of minimizing the number of recombinations in a phylogenetic network, constructed using binary DNA sequences, is NP-hard. In this paper, we propose a pattern recognition-based O(n²) time approach for constructing the phylogenetic network, where n is the number of nodes or sequences in the input data. The network is constructed with the restriction that no two cycles in the network share a common node.     

The concept of an endurance limit for adhesive joints

The effect of cyclic stressing on the strength of single lap adhesive joints has been studied and a considerable reduction in strength observed when the maximum stress exceeds about 40% of the ultimate tensile strength, but whether or not a true endurance limit exists is not proven. Fallacies are shown in some of the techniques which have been proposed for studying the fatigue behaviour of adhesive joints.     

Biaxiale Ermüdung reibrührgeschweißter Strukturelemente

Biaxial fatigue of friction stir welded stiffened panels Within the framework of the European WelAir project, cruciform specimens made from stiffening FSW overlap joints were fatigued in the DLR biaxial test rig. To resemble the loading situation of pressurized fuselage structures, proportional loading without any phase shift, but with different load ratios λ between the loading components in both directions was applied.Natural crack initiation and subsequent crack growth were governed by the stiffness gradient caused by introducing the stringer. Cracks initiated and propagated at run‐in and run‐out locations in a direction perpendicular to the weld seam. The shortest fatigue life was observed for uniaxial loading in welding direction (λ = 0). An additional stress component perpendicular to the joint line (λ > 0) resulted in a higher number of cycles to failure. Similar to single stringer panels, increasing the load ratio also increased the number of cycles to failure for FSW clip‐stringer structural members, but additionally gives a different location of the fatal crack.     

Symbolic control of visual attention: The role of working memory and attentional control settings.

This study examined how 1 symbol is selected to control the allocation of attention when several symbols appear in the visual field. In Experiments 1-3, the critical target feature was color, and it was found that uninformative central arrows that matched the color of the target were selected and produced unintentional shifts of attention (i.e., involuntary, initiated slowly, producing long-lasting facilitatory effects). Experiment 4 tested whether such selection is the result of an attentional filter or of a competition bias due to a match of incoming information against integrated object representations stored in working memory. Here, the critical feature was shape and color was irrelevant, but matching color arrows were still selected. Thus, features of objects in working memory will bias the selection of symbols in the visual field, and such selected symbols are capable of producing unintentional shifts of attention. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Simultaneous translation of lectures and speeches

With increasing globalization, communication across language and cultural boundaries is becoming an essential requirement of doing business, delivering education, and providing public services. Due to the considerable cost of human translation services, only a small fraction of text documents and an even smaller percentage of spoken encounters, such as international meetings and conferences, are translated, with most resorting to the use of a common language (e.g. English) or not taking place at all. Technology may provide a potentially revolutionary way out if real-time, domain-independent, simultaneous speech translation can be realized. In this paper, we present a simultaneous speech translation system based on statistical recognition and translation technology. We discuss the technology, various system improvements and propose mechanisms for user-friendly delivery of the result. Over extensive component and end-to-end system evaluations and comparisons with human translation performance, we conclude that machines can already deliver comprehensible simultaneous translation output. Moreover, while machine performance is affected by recognition errors (and thus can be improved), human performance is limited by the cognitive challenge of performing the task in real time.