在线气体分析系统在炼钢厂的应用

介绍宣钢炼钢厂转炉煤气回收过程的在线气体分析,比较激光分析仪和抽气式气体分析仪的工作原理及特点。     

锡膏激光扫描三维测量系统光强自适应调节技术

根据锡膏激光扫描三维测量系统在测量PCB电路板时底板和锡膏对激光光强的散射效果不同,设计并研制了一套光强自适应调节光源。该光源以程控电源为基础,分析光条中心提取效果与激光光强的关系,应用小波分解与频带能量比相结合的光强自适应调节算法实现测量系统光强自适应调节功能。进行了相关实验,实验结果表明该光源能够很好地实现锡膏激光扫描三维测量系统的激光光强自适应调节,并能选出最适合测量的激光光强,具有很好的适用性。     

激光测速仪在宽厚板轧机后测长的运用

随着国内厚板产量的增加,其市场竞争日趋激烈。为了更好的谋求发展,莱钢宽厚板厂在降低生产成本的同时,通过技术改造极大地提高产品的质量。因为板坯成材规格需要精确的长度数据,所以宽厚板板坯长度的精确测量就显得非常重要。本文主要介绍激光测速仪在轧机后测长系统中的应用。     

基于自由摆的平板精确控制与激光追踪系统

以TI公司的MSP430F5438单片机为控制核心,结合步进电机和精密电位器WDD35D-4,实现了基于自由摆的平板控制与激光追踪系统。当摆杆摆角为45°～60°时,平板可以承载8枚一元硬币,并在5个摆动周期内维持稳定;当摆杆摆角为30°～60°时,固定在摆杆平板上的激光笔可以在15s内找到并跟踪1.5m远处的靶心。     

CO2 laser annealing of plasma-deposited high-Tcsuperconducting thick films

Recent advances in the fabrication of high-T _c superconducting thick films demand processing techniques which can eliminate film/substrate interdifiusion that occurs during subsequent post-annealing heat treatment after the film is deposited, thereby limiting the application of the thick films for devices. The present study evaluates laser annealing techniques for plasma-deposited Y-Ba-Cu-O thick films using a high-energy CO₂ laser (10.6m) in a continuous wave mode. The results are compared with those obtained by conventional furnace annealing techniques necessary for post-heat treatment of as-deposited superconducting thick films. The high-T _c superconducting phase is recovered by cationic diffusion during subsequent post-annealing heat treatment. Crystallographic phases and microstructural characterization have been performed using XRD, SEM, and EPMA analytical techniques. The significance of the technology lies in the elimination of film/substrate interdiffusion problems, thereby resulting in high-quality superconducting thick films. The technology will significantly reduce the post-annealing times usually required by conventional furnace annealing techniques.     

Transistors made in laser recrystallized polysilicon on insulator films

lpcvd polycrystalline silicon films were deposited on thermally oxidized silicon as well as onlpcvd silicon nitride deposited on silicon. Acw argon ion laser was used to recrystallize the polysilicon film into large grains (grain size from 5μm to 40μm). Boron was then implanted and standard N-channel silicon gate process and N-channel metal gate process were carried out to realisemosfets on this material. Channel mobilities upto 450 cm²/V-sec for electrons have been measured. This thin filmmosfet has a four-terminal structure with a top and a bottom gate and the influence of one gate on the drain current due to the other gate has been investigated. Comparison of theI _D v-V _D curves of the devices with physical models was found in good agreement.     

Preadhesion Laser Treatment of Aluminum Surfaces

An excimer laser may be used for preadhesion treatment of aluminum alloys. This method presents an alternative to the use of ecologically unfriendly chemicals involved in conventional anodizing pretreatments.

Experimental results indicate that preadhesion laser surface treatment significantly improved the shear strength of modified-epoxy bonded aluminum specimens compared with untreated and anodized substrates. The best results were obtained with laser energy of about 0.2 J/Pulse/cm² where single lap shear strength was improved by 600-700% compared with that of untreated Al alloy, and by 40% compared with chromic acid anodizing pretreatment.

The mode of failure changed from adhesive to cohesive as the number of laser pulses increased during treatment. The latter phenomenon has been correlated with morphology changes as revealed by electron microscopy, and chemical modification as indicated by Auger and infrared spectroscopy.

It can be concluded that the excimer laser has potential as a precise, clean and simple preadhesion treatment of Al alloys.     

基于中红外QCL的痕量CO气体传感器

为了减少CO爆炸给国民经济造成的巨大损伤,提出了一种能够快速地监测环境空气中痕量CO的气体传感器。由于CO分子基频吸收谱带的吸收线强要比泛频带和组合频带的吸收线强高出2～3个数量级,选择激射中心波长为4.65μm中红外量子级联激光器（QCL）作为光源,同时再配合长光程Herriott气室提高了CO体积分数检测下限。同时,该传感器采用单光源双探测器差分光学结构,消除了电调制光源所带来的不稳定性。实验表明：该传感器CO体积分数检测下限为2×10-6,并且操作人员可以通过替换在不同波长下运行的中红外QCL来测量其它气体。     

浅谈玻璃钢的加工

本文在实际研究和应用的基础上，对玻璃钢的传统加工方法和特种加工方法，如激光切割、纯水射流切割和磨料水射流切割作了简要论述。     

基于GP2Y0A02距离测量的仿真与辅助设计

为了实现非接触距离测量,利用多个仿真与设计软件设计了采用GP2Y0A02模块的距离光学测试系统。在PROTEUS中测量GP2Y0A02电压值,并在Matlab中采用多元线性回归建立GP2Y0A02电压与距离的拟合曲线,最后在开发的测量程序中利用拟合曲线求解得到距离量。测试结果表明,对于非线性位置测量采用适当数据处理方法能得到满意的测量精度。