Liquid-Phase Transport During Removal of Organic Binders in Injection-Molded Ceramics

A method has been developed for calculating hydraulic pressures induced by thermal expansion of liquid binders early in the removal cycle, when evaporative losses are negligible and fully saturated conditions prevail. Specific results were obtained for flat compacts containing a common wax binder, mixed with varying amounts of low-density polyethylne. In general, these results show how the risk of hydraulic fracture increases with heating rate and compact thickness. Although pressures are minimal when the binder consists entirely of wax, the continual addition of polyethylene eventually gives rise to unacceptable risk levels, even for relatively thin compacts. Binder removal at elevated temperatures is considered subsequently. In this case, vapor pressures eventually approach a critical level, thereby allowing mass removal by evaporation to overcome the effect of thermal expansion in maintaining full saturation. With the onset of void formation, the developing capillary pressure supersedes hydraulic pressure as the driving force in liquid transport. Besides representing capillary flow, the present formulation also accounts for thermal degradation of the binder during removal. The resulting system of equations was solved numerically for a variety of representative debinding conditions. Predictions for flat compact containing a balanced wax/polyethylene binder indicate that thermal degradation of the polyethylene can give rise to a marked improvement in debinding rates. It turns out, however, that this enhancement is far more effective in thinner compacts.     

电纺直写制备聚己内酯支架形貌及精度

作为一种新型的微纳制造技术，熔体直写电纺被广泛用于组织工程支架的可控制备,有序的纤维沉积是该领域应用的前提条件。对于支架成型精度的探究，本文使用生物可降解材料聚己内酯（PCL），采用自行设计的熔体电纺三维可控成型设备进行实验，考察了纤维间距对二维并行纤维沉积形貌及成型精度的影响，以及纺丝电压和网格大小对三维网格结构形貌及精度影响。结果表明，随着并行纤维设定距离的增大，纤维的沉积误差减小，并最终趋于平稳。对于三维网格结构，随电压的增加，最大沉积层数量先增大后减小，当纺丝电压为6kV时达到最大沉积层数15层。成型精度误差先减小后增大，当纺丝电压为7kV时，精度最高误差小于5%。随设定网格边长的增大，沉积层数不断增大。成型精度逐渐提高，当网格边长大于等于1.5mm时，沉积误差趋于稳定，并维持在5%左右。     

A novel algorithm for layout optimization of injection process with random demands and sequence dependent setup times

Injection molding is an ideal manufacturing process for producing high volumes of products from both thermoplastic and thermo setting materials. Nevertheless, in some cases, this type of manufacturing process decelerates the production rate as a bottleneck. Thus, layout optimization plays a crucial role in this type of problem in terms of increasing the efficiency of the production line. In this regard, a novel computer simulation–stochastic data envelopment analysis (CS-SDEA) algorithm is proposed in this paper to deal with a single row job-shop layout problem in an injection molding process. First, the system is modeled with discrete-event-simulation as a powerful tool for analyzing complex stochastic systems. Then, due to lack of information about some operational parameters, theory of uncertainty is imported to the simulation model. Finally, an output-oriented stochastic DEA model is used for ranking the outputs of simulation model. The proposed CS-SDEA algorithm is capable of modeling and optimizing non-linear, stochastic, and uncertain injection process problems. The solution quality is illustrated by an actual case study in a refrigerator manufacturing company.     

低密度冷模塑聚氨酯软质泡沫塑料

介绍了低密度冷模塑聚氨酯软质泡沫塑料的配方体系，工艺特点及泡沫性能。指出该泡沫应用范围较广，发展前景甚好。     

Compounding and injection molding of polybutene‐1/polypropylene blends

The effect of shear‐controlled orientation injection molding (SCORIM) was investigated for polybutene‐1/polypropylene blends. This article reports on the methods and processing conditions used for blending and injection molding. The properties of SCORIM moldings are compared with those of conventional moldings. SCORIM is based on the application of specific macroscopic shears to a solidifying melt. The multiple shear action enhances molecular alignment. The moldings were investigated with mechanical tests, differential scanning calorimetry studies, and polarized light microscopy. The application of SCORIM improved Young's modulus and the ultimate tensile strength. The gain in stiffness was greater for higher polybutene‐1 content blends. A drastic decrease in the strain at break and toughness was observed in SCORIM moldings. The enhanced molecular orientation of SCORIM moldings resulted in a featureless appearance of the morphology. Interfacial features due to segregation were visible in the micrographs of SCORIM moldings. Both conventional and SCORIM moldings exhibited form I′ in polybutene‐1. This article explains the relationship between the mechanical properties and micromorphologies. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 88: 806–813, 2003     

Unique clay orientation in the injection-molded bar of isotactic polypropylene/clay nanocomposite

In this article, the injection-molded bars of isotactic polypropylene/organoclay nanocomposite with different clay contents have been obtained via dynamic packing injection molding (DPIM). The oriented microstructure including layered nanoparticles and PP lamellae has been inspected through 2D-WAXS analyses along the sample thickness of the molded bars. Depending on the clay content and sample thickness, various oriented clay structures with nanoparticles uniplanar-axially oriented parallel to the surface of molded bar, or partially tumbled around the flow axis of the molded bar, or even a random orientation, could be observed. The observed orientation behavior of nanoparticles could be temporarily elucidated as the results of the sensitive response of layered nanoparticles to shear deformation and the structural recovery of clay network assisted by the electrostatic attraction existing between adjacent nanoplatelets.     

The effect of cooling rate on the impact performance and dynamic mechanical properties of rotationally molded metallocene catalyzed linear low density polyethylene

This article examines changes to the morphology of rotationally molded metallocene catalyzed linear low density polyethylene brought about by varying the cooling rate during processing. These changes in morphology lead to variations in the impact performance, which is reflected in the dynamic mechanical characteristics of the materials. Various analytical techniques are used in an attempt to explain the differences in impact behavior. Slow cooling is shown to result in high crystallinity, and in the formation of large spherulites, which in turn is detrimental to the impact performance of the material, particularly at low temperatures. The high crystallinity corresponds with a shift in the β transition of the material to a higher temperature, and is shown to result in a higher brittle–ductile transition. A case study was also carried out on samples from a finished part provided by an industrial molder, one section of which failed in a brittle manner when impact tested while the other failed in a ductile manner. Microscopy results showed that the brittle material had large spherulites at the inside surface, while the ductile material showed incipient degradation at this surface, which has previously been shown to be of benefit to impact strength in rotationally molded parts. Dynamic mechanical studies again showed a β transition at a higher temperature in the brittle samples. © 2006 Wiley Periodicals, Inc. J Appl Polym Sci 101: 1963–1971, 2006     

复合材料RTM模具的制备

根据树脂传递模塑(RTM)模具对基体树脂的基本要求,选用双酚A环氧乙烯基酯树脂为基体,聚乙酸乙烯酯为低收缩添加剂,玻璃纤维经编织物为增强材料,并加入相应的助剂,制备了复合材料RTM模具。该模具具有成本较低、开发周期短、精度较高等优点,但表面强度和热效率较低。     

工艺参数对陶瓷注射成型的影响与分析

本研究通过改变注射温度，注射压力，保压压力等几个主要参数，对形状，体积不同的注射成型体，试条，圆柱及子部件进行了一系列注射工艺实验。相应地对成型体的密度，弯曲强度及烧结体的密度和强度进行测量，并从陶瓷注射成型混合物的流动行为，热物理特性方面对注射这一复杂过程进行分析，探讨工艺参数对成型过程的内在影响，从而确定合理的注射工艺条件。     

氟树脂性能与加工应用(续10)

介绍了聚四氟乙烯悬浮树脂成型加工有关的物理性能,树脂的成型加工及选用方法.分别叙述了模压成型、自动模压成型和液压成型的原理、过程及设备.