微通道电泳芯片系统中信号识别算法的设计与实现

介绍适用于微通道电泳芯片系统的DNA测序软件的总体流程，以及其中的信号处理与识别算法。以激光诱导荧光检测系统所采集到的原始数据为源信号，以小波平滑和小波去噪为理论基础，将滤波算法和峰值识别算法综合在一起进行设计，从而使其适用于检测速度更快、样品量更少的微通道电泳芯片系统。将本算法应用于DNA片段的分离实验中，可以有效地达到滤波以及信号识别的目的。     

受干扰波相位测量的一种新方法

为了测量受噪声和谐波干扰的两个信号间的相位差，基于自适应带通滤波器（ABF）和测量信道交换技术，提出了一种新的测量方法。ABF采用可编程开关电容滤波器（PSCF）和锁相环，明显地抑制了噪声和谐波干扰，频率跟踪范围超过四个倍频程（0．5Hz-6kHz）。用微处理器控制4个开关来交换测量信道，可以基本上消除测量通道引入的附加相位移。两种方法结合提高了相位差的测量精度。实验说明了该测量方法的有效性，该方法也适合于被测信号为慢时变情况。     

A novel design in composities of various materials for solar selective coatings

This study describes the development of multilayer metal-dielectric graded index solar selective coatings in which the metallic volume fraction increases with depth, from top (air–film interface) to bottom (film–substrate interface). The work is based on computer simulation followed by validation through fabrication of the coatings and optical measurements. The influence of the choice of the number of layers present in a graded index composite selective absorber and results obtained for a new destructive interference bilayer (four-layer system) coating, designed using the computer model, were studied. The design and optimization of the composite coating was undertaken using a computer tool developed within this program of research employing Bruggeman and Maxwell–Garnett effective medium formalisms. The design tool enabled all key design parameters, with the exception of particle size and orientation, to be varied systematically to permit the sensitivity of the optical properties of the selective absorber coating to be studied.The model was validated with a supporting program of experimental research in which many different selective absorbers were prepared by co-sputtering of metal and dielectric materials.Although the best compositional gradation can be achieved by increasing the number of layers, the variation in optical performance beyond a certain number of layers is minimal. The destructive interference produced between adjacent layers contributes to the absorptance. The effect of the number of layers (single, four and 10) has been calculated for various materials such as nickel, vanadium, tungsten, cobalt and chromium based coatings. Solar absorptance of 0.98 and 0.96 was achieved by simulation and experimental findings with less than 0.07 thermal emittance at 300 K for 200 nm thick, 4-PGSAC (four-layer system) of V : Al₂O₃ composites. Other designs showed lower optical performance for all the material combinations regardless of their individual optical properties. Use of such thin film coating on the absorbers of solar thermal appliances can reduce thermal losses significantly, which could be of importance to the relevant industry.     

自动化安全监测系统在太平湖水库消险加固工程中的应用

太平源水库位于嫩江一级支流黄蒿沟上，控制面积683km^2，设计标准为100年一遇，2000年一遇校核，工程等别为大Ⅱ型，设计总加容1．53m^3。1999年12月被鉴定为三类病险率，原有观测设施基本报废，不有满足水库消险加固后的正常运行需要。为确保大坝安全，采用新的监测设备和技术。安装一套大坝安全自动化监测系统，对大坝安全状况进行自动监测与分析汇总。     

低相噪,低杂波数字锁相环路滤波器的设计

较详细地分析数字锁相频率合成器的相位噪声，着重用控制论方法对低相噪、低杂波锁相环的环路滤波器进行设计，并用某Ｓ波段频率合成器的实验结果进行了验证。     

有源OTA─C高通滤波器

本文提出了一种实现高通滤波特性的高阶ＯＴＡ－Ｃ滤波器，其实验结果和理论分析相一致。     

群时延精确设计的全差分四阶Bessel滤波器

采用MOS管有源电阻,提出了一种全差分R-MOSFET-C四阶Bessel有源低通滤波器,.通过调节工作于亚阈值区的CMOS管的沟道导纳补偿电阻值的大小,能抵消集成电路制造工艺中电阻值的一致偏差,实现Bessel有源滤波器群时延的精确设计.根据无源滤波器的状态方程完成有源滤波器的综合,应用3.3V,0.5μm CMOS工艺完成了群时延大小为0.75μs的四阶Bessel低通滤波器的管极计算机仿真,仿真结果表明所提电路正确有效,适于全集成.     

A novel laboratory bench for practical evaluation of catalysts useful for simultaneous conversion of NOx and soot in diesel exhaust

This study deals with the development of a laboratory bench for the practical evaluation of catalysts that are useful for the direct conversion of NO_x and soot in the exhaust of diesel engines. The employed model exhaust is generated by using a diffusion burner with additionally dosing some gaseous components to the burner gas to obtain a realistic feed composition. The produced soot is extensively characterized by employing thermogravimetry, transmission electron microscopy, N₂ physisorption and temperature programmed techniques. The results of the different characterization methods show that the present soot is suitable for the intended catalytic investigations. The simultaneous conversion of NO_x and soot is examined like in practice, i.e. the soot is separated from the tail gas by a diesel particulate filter (DPF) that is coated with the catalyst. The deposited soot is then catalytically converted by NO_x and O₂ to form N₂ and CO₂. The conversions of NO_x and soot are measured by exclusively applying gas analysers, whereby a special experimental procedure is developed to determine the soot removal. Hence, additional soot related analytics are not required. To show the suitability of the constructed bench a Pt/Fe₂O₃/β-zeolite sample is taken as test catalyst that is reported to be very active in NO_x/soot reaction. The measurements performed with and without catalyst clearly show the effect of the used sample in simultaneous NO_x/soot conversion. We therefore consider the constructed laboratory bench to be a useful tool for testing and ranking catalytic materials.     

大电流监测信号提取的光收发及信号处理

近年来,大电流的监测成了人们十分关心的问题,这是由于大电流有强磁、高压、电流大等一系列的直接监测所不能克服的问题。这就需要把高压大电流的强电信号,经过提取后变成能在实验室中直接观测的弱电信号。为此,如何从高压大电流的信号中提取出随实时信号变化而实时变化的小信号就变成了一个关键问题。详细介绍了监测信号提取的光收发电路原理和后续信号处理电路,分析了各部分的作用,给出了必要的分析结果。     

从销钉起家的“正业电子”

本文介绍了参观“正业电子有限公司”的概况。