Connecting the second exhaust-heat boiler to the operating first one under the conditions of flow circuits of combined-cycle plants with two gas-turbine units and one steam turbine

Problems arising with connecting the second exhaust-heat boiler to the first exhaust-heat boiler under load in the case of flow circuits of combined-cycle plants of type PGU-450 are considered. Similar problems exist for two-boiler single-turbine units of type PGU-325 and for two-boiler single-turbine units of traditional steampower plants with an output of 200–300 MW upon connection of the second furnace of a two-furnace boiler to the operating first furnace. Analysis of the temperature-induced stressed state and of the cyclic strength of thick-walled elements of the steam-water conduit of PGU-450 and of two-furnace boilers of two-boiler single-turbine units with an output of 200–300 MW (the check valve, the inlet header of the water economizer) is used for determining the steam temperature differences in the high-pressure conduits to the steam turbine and the order of connection of the second exhaust-heat boiler to the operating fist one. Modes of enabling a two-boiler single-turbine unit of a combined-cycle plant, which are most “rigid” from the standpoint of thermal strength, are determined. __________ Translated from élektricheskie Stantsii, No. 2, February 2006, pp. 11–17.     

Finite-element analysis and experimental study on tensile fatigue behaviour of bitumen–stone adhesion

Tensile fatigue behaviours of bitumen–stone adhesion were investigated using a dynamic mechanics analyser under stress‐controlled mode at two temperatures of 5 and 25°C and various controlled‐stress levels. Failure characteristics including interfacial failure and cohesive failure were examined using image analysis of fracture surfaces. Finite‐element analysis on stress distributions was conducted under different temperatures, film thickness and interfacial bonding conditions. A Coulomb–Mohr like criterion in combination with shear and normal stresses is proposed to deal with the extreme thin adhesive layer, which can be further simplified into an adhesive zone without significant loss of accuracy for stress analysis.     

一种新的高次边缘元方法

讨论了一种新的高次边缘元方法，它不仅消除了伪解，并具有简单高效的特点．着重研究了二次边缘元的空间构造；给出了有关计算公式．对具有精确解的条形介质填充波导主模和高次模本征值的计算表明：二次边缘元方法的计算精度比一次边缘元提高约一个数量级．块状介质填充和衬底各向异性的微带线主模色散曲线的计算证实了该方法的精确性和广泛的适用性．     

Prediction of fatigue behaviour in stress-concentrators of arbitrary geometry

A new method is outlined which aims to predict high-cycle fatigue behavior of components which fail from stress-concentrators. This involves examination of the stress field in the vicinity of the stress-concentrator, and comparison with stress fields for cracks at known stress intensities. Methods which are currently used for simple notch geometries can thus be generalised, making the approach applicable to stress concentrators of any geometry. The method of prediction is shown to be stable, providing a solution of good accuracy when compared to analytical methods for standard specimen geometries. Favourable comparisons with experimental data have been achieved both for standard notches and for a corner geometry which represents a typical component case.     

Finite-element simulation of moving induction heat treatment

An efficient finite-element procedure with a remesh scheme has been developed for the analysis of the moving induction heat treatment process, wherein relative motion occurs between the coil and the workpiece. In this procedure, the magnetic field is first simulated by using an updated mesh that tracks the moving coil position; the moving heat source within the workpiece material is derived from the magnetic field. The heat equation is then solved to obtain the temperature field created by the heat source. The procedure has been applied to calculate the temperature distributions in 1080 carbon steel cylinders during induction heating. The calculations have been validated by comparison with analytical solutions for the temperature distribution obtained using Green’s function methods. Finally, the temperature, residual stress, and microstructure distributions in quenched 1080 steel cylinders have been obtained using the finite-element procedure. Quenching of the heated cylinders, by both a moving cooling ring and a stationary liquid bath, has been analyzed. The finite-element procedure presented incorporates temperature-dependent material properties, phase transformations occurring in the 1080 steel, the change in magnetic permeability of the 1080 steel at the Curie temperature, and an elastoplastic stress model based on a mixed hardening rule. The simulation results demonstrate that the finite-element procedure could be applied to a variety of moving induction heat treatment problems to determine the residual stress and microstructure distributions in the heat-treated component. It also could be used in the design of process parameters and coils.     

光纤黑体腔高温传感器感温腔体的ANSYS分析

为了提高光纤黑体腔式高温传感器感温腔体的辐射性能,使腔体接近于理想黑体辐射状态,计算了腔体的有效发射率。基于ANSYS有限元方法对感温腔进行热辐射分析,讨论了腔底的形状、腔体温度、腔长、材料表面发射率、腔体的不等温分布对有效发射率的影响关系。结果表明,有效发射率会随着腔长的增加而增大,但会存在一个饱和值。同时当腔体处于非等温时,有效发射率随非等温程度近似呈直线下滑。综合分析结果,可以得出感温腔的优化构造参数,对传感器的制作以及提高传感器的测温准确性、分辨力和灵敏度有指导意义。     

胶层厚度对拉伸试样应力分布影响的数值分析

运用弹塑性有限元法研究了胶层厚度对承受拉伸载荷的对接接头胶层内应力分布的影响．三维有限元法数值分析的结果表明，随胶层厚度减小，胶层中正应力SZ与剪应力SYZ的分布趋于均匀；而对正应力SY而言，胶层厚度为0．15mm时，其边缘峰值应力最低。     

Direct Measurement of Transformation Zone Strains in Toughened Zirconia

Residual strains responsible for crack tip shielding have been measured within transformation zones surrounding cracks in Mg-PSZ. Two techniques were used for strain measurement: moiré interferometry and high-resolution image matching. Both methods provide maps of differential in-plane displacements within the specimen surface intersected by the crack, the latter method with the higher resolution. The results are compared with finite-element analysis to assess surface relaxation effects, and the measured strains are used to evaluate the crack tip shielding stress intensity factor. Calculations based on the assumption that the unconstrained transformation strain is hydrostatic dilatation yielded results that were significantly smaller than the measured toughness increases.     

Requirement of ultra-high voltage GIS arrester to voltage gradient of metal-oxide varistor

The surge arrester with excellent protection characteristics would decrease the overvoltage level ap- plied on the power apparatus to reduce their insulation levels and manufacturing bottleneck. The arrester for the 1000-kV ultra-high voltage ac power transmission system is designed as tank-type structure. The field-circuit combination numerical method combining the three-dimensional finite element method with circuit is proposed to analyze the potential distribution of GIS arrester. By comparing several design schemes, the most effective method to improve the potential distribution along the varistor column is to increase the voltage gradient of the ZnO varistor. Synthesizing several influential factors, the suitable voltage gradient of ZnO varistor should be controlled to 435 V/mm, and the resulted nonuniform degree of the potential distribution along the varistor column inside the GIS arrester would be controlled smaller than 10%. The result in this paper provides the fundamental technical index for the study of the high voltage gradient ZnO varistors.     

Effect of extrusion wheel angular velocity on continuous extrusion forming process of copper concave bus bar

The continuous extrusion forming process for producing large section copper concave bus bar under different extrusion wheel angular velocities was studied by three-dimensional finite element technology based on software DEFORM-3D. The rigid-viscoplastic constitutive equation was employed in the model. The numerical simulation results show that the deformation body flow velocity in the die orifice increases gradually with the increase of the extrusion wheel angular velocity. But slippage between the rod and extrusion wheel occurs when the extrusion wheel angular velocity is high. The effective stress near the die orifice enhances gradually with increasing extrusion wheel angular velocity. High stress is concentrated in adjacent regions of the flash gap. The effective strain gradient is greater near the abutment than that near the die orifice. The effective strain of the product increases gradually with increasing extrusion wheel angular velocity. In the deformation process, the deformation body temperature increases remarkably due to friction and deformation. So the cooling is necessary in the region of the die and tools.