Yttrium sol–gel coating effects on the cyclic oxidation behaviour of 304 stainless steel

The present results reveal the interest of sol–gel coating technique to improve 304 steel high temperature oxidation resistance. An yttrium sol–gel coating appears to enhance the oxidation resistance during isothermal oxidation test, to decrease widely the oxide weight gain and to reduce the initial transient oxidation stage generally observed in the case of blank steels. Moreover, the experimental results confirm that yttrium sol–gel coating also plays a significant role on the cyclic oxidation behaviour of the 304 steel. In fact, the yttrium addition promotes remarkably the prolongation of the period during which the oxide scale still remains adherent to the substrate.     

Long-term measurements of the concentrations of halocarbons in an urban area of Kraków, Poland

The results of the measurements of the concentrations of freons (F-11 and F-113), chloroform (CHCl₃), trichloroethane (CH₃CCl₃) and carbon tetrachloride (CCl₄) in air are presented. The data concern concentration measurements that have been conducted in Krakow since half way through 1997 to the end of 1999. The mean monthly values of these concentrations have been compared with the data from Mace Head, the station situated at a similar longitude as Krakow. It has been concluded that, in the observed period of time, the concentrations of the pollutants in Krakow are higher than in Mace Head. The mean monthly concentrations of F-11 and CCl₄ decrease in Krakow faster than in Mace Head (2.5 and 3.3 times, respectively). The concentrations of CHCl₃ and CH₃CCl₃ decrease at both locations, but the change is greater in Krakow. In Krakow, the observed increase of F-113 is 0.13 ppt/month and has an opposite trend than in the same period at Mace Head.     

降凝剂对高蜡稠油的改性效果及机理研究

实验研究了工业品原油降凝剂WHP改善含蜡56.9%、其中96.6%为正构烷烃的胜利郑王庄稠油流动性的效果。WHP含乙烯/醋酸乙烯/乙烯醇嵌段聚醚三元共聚物30%-35%。在60℃将WHP加入稠油中,测定其凝点和32℃、0-42.6 s^-1范围5个剪切速率下的黏度,均随WHP加量的增加（50-300 mg/L）而降低,200 mg/L为最佳加量,在该加量下0.32 s^-1黏度由34.16 Pa·s降至79.2 mPa·s,凝点（℃）、屈服值（Pa）、稠度系数（Pa·s^n）分别由49.0、32.42、31.57降至39.5、0.1297、0.02142,流型指数由0.1176升至0.9790。由黏温曲线求出,加入200mg/L WHP使该稠油析蜡点由65℃降至58℃,反常点由70℃降至50℃。根据空白和加剂原油扫描电镜照片显示的蜡晶形态,利用共晶机理分析讨论了WHP这种高分子表面活性剂的降凝、降黏、改善流动性的作用。图3表3参5。     

杜84断块超稠油开发中后期稳产对策研究

对杜84断块超稠油生产中后期暴露的主要矛盾，即随着轮次升高，周期吞吐效果变差，井下技术状况日益变差。油层动用不均，汽窜加剧等问题进行了分析。并提出了相应的稳产对策-实施多井整体吞吐，大修复产，调剖等措施。现场应用证明，这些措施基本能够确保杜84断块超稠油中后期的稳产。     

三峡工程明渠提前截流方案及水力学试验研究

论述了三期明渠提前截流方案的综合比较分析及截流水力学试验研究成果。认为拟定的提前截流诸方案各有利弊 ,其截流难度较初设方案显著增加。对于截流“基本方案”及“比较方案”的成功实施 ,必须辅之以一定的工程技术措施降低截流难度     

In Situ Formation of a Novel Nanocomposite Structure Based on MCM-41 and Polyethylene

M41S materials are prepared by in situ assembly of inorganic precursors and organic template and can be viewed as nanocomposites of the siliceous phase and organic surfactant. Calcination of these precursors gives the M41S materials that have been used to prepare novel nanocomposite structures, in which the organic phase inside the nano-sized pores is isolated by the nano-sized inorganic pore walls. The nanocomposite structures can be formed by in situ polymerization of monomers inside the channels. Polymerization of ethylene takes place inside the nano-sized pores, producing the desired nanocomposite structure. The resulting polyethylene was found to be a mixture of crystalline and amorphous phases.     

城市燃气管网设计若干问题的探讨

分析了哈依燃气管道工程在施工及管理过程中存在的问题，并就如何解决这些问题提出了建议。     

砖混结构现浇楼板的裂缝分析及预防措施

针对目前多层住宅采用砖混结构现浇钢筋混凝土产生裂缝的情况，分析了其产生原因，提出了预防措施。指出这些预防措施可使裂缝得到有效控制。