基于人文关怀的信号配时方法研究

在传统的信号配时中，都是以减少车辆的总延误为目标，这样并不能很好地体现出整个社会中人的时间价值。现以减少所有通过交叉口的出行者的总延误为目标，在传统的信号配时方案的基础上，提出了一套新的配时方案，同时以减少全部出行者的总延误时间为目标给出了相应的延误评价公式，最后以杭州市文一路-古翠路口的实测交通数据进行分析，论证了本配时方案的有效性。     

一种简单的S参数去嵌入技术

介绍了在低成本夹具上，任意微带结构二端口网络S参数去嵌入的方法；该方法用于获取放大器模块的S参数，根据这些参数设计的C波段的放大器实测结果与仿真一致。     

Tensile fracture and failure behavior of technical flax fibers

The apparent tensile strength of technical flax fibers was determined in single‐fiber tests at various clamping lengths (20, 40, and 80 mm) and the outcome was compared with literature data. It was demonstrated that the strength of flax at each clamping length obeyed the two‐parameter Weibull model. The failure mode and sequence were studied in situ (i.e., during loading) by SEM and acoustic emission (AE). The failure sequence (axial splitting of the technical fiber along its elementary constituents, radial cracking of the elementary fibers, multiple fracture of the elementary fibers) concluded reflected the hierarchical build‐up of the flax bast fibers. To the above failure events AE amplitude ranges were assigned. © 2003 Wiley Periodicals, Inc. J Appl Polym Sci 90: 3638–3645, 2003     

Schäden durch kerbinduzierte Schwingbrüche

Failures by notch induced fatigue fractures Notches produce local stress concentrations and promote the formation of fatigue cracks. Characteristic types of notches as a result of design, manufacturing and operation are presented and remedial measures are discussed. Examples demonstrate the effect of different kinds of notches on various components.     

一种可切削玻璃陶瓷的压痕断裂特性

将断裂韧性测试的压痕方法与压痕弯曲方法相结合，独立地分离出了压痕残余应力因子ｘ，使其成为可测参量，并建立了压痕一压痕弯曲的断裂韧性测试方法．将这种方法应用于一种可切削玻璃陶瓷的测试，获得的Ｋ１ｃ值为Ｋ１ｃ＝２．０３ＭＰａ·ｍ１／２，与单边切口法（ＳＥＮＢ）获得的Ｋ１ｃ值有较好的一致性．测得的残余应力因子Ｘ＝０．０９３，符合Ａｎｓｔｉｓ经验公式的预测．     

VCM压缩机曲轴断裂失效分析

介绍了锦化化工(集团)有限责任公司出现的VCM压缩机曲轴断裂事故，并从断口的部位、形貌特征，断轴的几何状态、受力状态及树料性能等方面分析了曲轴断裂的根本原因。     

Finite elements in the analysis of pressure vessels and piping-a bibliography (1976–1996)

The paper gives a bibliographical review of the finite element methods (FEMs) applied for the analysis of pressure vessel structures/components and piping from the theoretical as well as practical points of view. The range of applications of FEMs in this area is wide and cannot be presented in a single paper; therefore the aim of this review is to give the reader an encyclopaedic view of the differnt possibilities that exist today for the finite element analysis in the fields of pressure vessels and piping. The bibliography at the end of the paper contains approximately 1900 references to papers, conference proceedings and theses/dissertations on the subject that were published in 1976–1996. These are classified in the following categories: linear and non-linear, static and dynamic, stress and deflection analysis; stability problems; thermal problems; fracture mechanics problems; contact problems; fluid-structure interaction problems; manufacturing of pipes and tubes; welded pipes and pressure vessel components; development of special finite elements for pressure vessels and pipes; finite element software; and other topics. Also finite element software, general purpose and special purpose codes, used for the analysis of pressure vessels and pipes are briefly discussed and presented.     

�õر���ʯ������ָʾdz��������

本文介绍了运用地表岩石吸附烃法指示四川浅层油气藏,发现吸附烃异常与油气井产能有良好吻合性,反映了地下裂缝系统和油气聚集的分布。并对实验条件、各种可能的影响因素及一些基础理论问题进行了实验分析和讨论。     

Non-steady-state model for kinetics of free radical polymerization, 4. Direct thermal initiation

This paper deals with the non-steady-state kinetics of direct thermal initiated polymerization. The initiation is assumed to be a bimolecular reaction of the monomer. The relationship between the radical concentration and the monomer conversion is rigorously derived. In further treatment a few very close approximations are introduced based on the fact that the number of monomer molecules reacting in the initiation step is much less than that consumed in the propagation step for a process producing high polymer, and the value of the rate constant for propagation or chain transfer is much lower than that for chain termination. Expressions for various molecular parameters, such as molecular weight distribution, number-average and weight-average degrees of polymerization, and dispersity, are given. Several numerical examples are provided.