热变形对多元合金耐磨铸铁组织和性能的影响

研究了热变形量对多元合金耐磨铸铁组织和冲击韧度的影响，结果表明，热变形能改变耐磨铸铁组织中共晶碳化物的形状与分布，促进颗粒状碳化物的析出，提高耐磨铸铁的冲击韧度。当该耐磨铸铁的热变形量为40％时，其冲击韧度最佳。     

25Cr3Mo3NiNb二次硬化钢冲击性能的研究

研究了二次硬化钢25Cr3Mo3NiNb的冲击韧度随回火温度和试验温度的变化.结果发现,试验钢在200℃回火时冲击韧度较高,300～600℃回火时冲击韧度值较低,600℃以上回火时冲击韧度值迅速升高,640℃回火时冲击韧度达到最高值55J/cm2,640℃以上回火时冲击韧度值有所降低.640℃回火后试验钢的冷脆转变温度为10℃,屈服强度为960MPa,可以满足兵器特种结构件高强度高韧性的要求.     

Impact toughness of tungsten films deposited on martensite stainless steel

Tungsten films were deposited on stainless steel Charpy specimens by magnetron sputtering followed by electron beam heat treatment. Charpy impact tests and scanning electron microscopy were used to investigate the ductile-brittle transition behavior of the specimens. With decreasing test temperature the fracture mode was transformed from ductile to brittle for both kinds of specimens with and without W films. The data of the crack initiation energy, crack propagation energy, impact absorbing energy, fracture time and deflection as well as the fracture morphologies at test temperature of-70 ℃ show that W films can improve the impact toughness of stainless steel.     

提高钻杆接头冲击功的工艺方法

针对石油钻井关键产品高强度钻杆接头的使用要求,在保证强度指标要求非常高的前提下,研究摸索增加高温正火后再调质的工艺方法,以改善接头材料原始微观带状组织和纤维结构,细化晶粒,提高钻杆接头的冲击功,使该产品力学性能达到API标准的要求。     

某汽车车轮半轴断裂失效分析

对某汽车事故后的现场检查中发现其左后轮半轴断裂.为了判断该半轴的断裂性质及原因,对断裂半轴的外观进行了检查,对断裂半轴的断口进行了宏微观观察,对半轴材料进行了金相组织检查、硬度测试以及化学成分检测.结果表明,半轴的断裂是由于受到超过正常值的冲击载荷而产生的过载断裂,与其材质及加工工艺无关.     

2205双相不锈钢模拟焊接HAZ组织与性能

采用热模拟法研究了2205DSS焊接HAZ的组织与性能，探讨了冷却时间对模拟HAZ冲击韧性的影响规律。结果表明：冷却时间对组织及性能有很大的影响，随冷却时间的延长，铁素体含量减少，奥氏体含量增加，冲击韧性增大：随冷却时间延长，模拟组织显微硬度降低，而且模拟组织中铁素体的硬度低于奥氏体的硬度：固定冷却时间t8／5时，随冷却时间t12／8的增加，冲击韧性提高：固定冷却时间t12／8时，随冷却时间t8／5的增加，冲击韧性降低。     

预应变下焊接接头冲击韧度及韧-脆转变的分析

以常用建筑结构钢(16Mn和Q235B)为研究对象，通过不同温度下的夏比冲击试验研究预应变对其母材和焊缝冲击性能的影响。结果表明，材料在预应变下无论是母材还是焊缝夏比冲击韧度均有所降低，韧一脆转变温度有所提高。5％预应变后的16Mn母材和焊缝其韧一脆转变温度均低于室温(20℃)，因此仍可在室温下安全使用；Q235B钢室温下冲击韧度较16Mn钢低，且预应变对母材影响更大，和未经预应变冲击值相比，降低了三倍有余。可以看出，Q235B钢的抗震性能较16Mn差。研究发现：为建立客观的材料韧度指标和进行更有效的安全分析时，预应变也应该作为一个考虑因素。     

提高高铬白口铸铁磨球冲击抗力的技术关键

当高铬白口铸铁含铬量为18%～28%,Cr/C值是8￣9,铸铁的显微组织是回火马氏体 少量残余奥氏体(<5%) M7C3碳化物,则磨球具有高的冲击韧性和断裂韧性K1C,具有高的冲击抗力,表现出低的冲击剥落量。     

ANN valuation model of material LCIA profile

Weighting model is the only valuation model of life cycle impact assessment(LCIA) profile now. It simplifies evaluation function into linear function, and makes the determination of weighting factor complicated. Therefore the valuation of LCIA profile is the most critical and controversial step in life cycle assessment(LCA). Development on valuation models, which are understood easily and accepted widely, is urgently needed in the field of LCA.The modeling approaches for the linear evaluation function were summed up. The modeling approaches for the nonlinear evaluation function were set up by function approximation theory, which include choosing preference products, forming preference data, establishing artificial neural network(ANN) and training ANN by preference data.By selecting 7 material products as preference product, experience was done with modeling approaches of the nonlinear evaluation function. The results show that the modeling approaches and valuation model of the nonlinear evaluation function are more practical than the weighting model.     

热处理工艺对铸造3Cr2MoWVNi热锻模具钢冲击韧度和硬度的影响

研究了热处理工艺对铸造3Cr2MoWVNi热锻模具钢冲击韧度和硬度的影响，结果表明：试验钢在1050℃淬火，650℃回火下，冲击韧度和硬度达到最佳值，分别为72.3J/cm^2和34.5HRC。在最佳热处理工艺下，经RE－Nb变质处理的试验钢的冲击韧度较未变质处理的试验钢有明显提高。