Experimental evaluation of the strength distribution of E-glass fibres at high strain rates

A bimodal Weibull distribution function was applied to analyse the strength distribution of glass fibre bundles under tensile impact. The simulation was performed using a one-dimensional damage constitutive model. The results show that there were two concurrent flaw populations in the fracture process. The regression analysis using the bimodal Weibull distribution function was in good agreement with experiment.     

泡沫铝的动态压缩性能和吸能性研究

通过测量泡沫铝在动态和准静态压缩条件下的应力 -应变曲线 ,研究了泡沫铝的准静态和动态压缩行为以及不同应变条件下的吸能性 ,并对其应变率效应进行了分析。结果表明 ,在高应变速率和准静态压缩下 ,泡沫铝的σ -ε曲线均表现出弹性变形段、平缓段和密实段三阶段特征 ;泡沫铝的压缩性能具有明显的应变速率敏感性 ,随应变速率的提高 ,流动应力上升 ,吸能性升高     

材质对蜂窝纸板缓冲性能的影响

对两种不同材质的蜂窝纸板静态应力应变性能和动态缓冲结果进行了比较分析。讨论了蜂窝纸板力学性能对应变速度的敏感性及两种纸板的缓冲性能差异。缓冲试验结果表明。在不同的冲击应变率下蜂窝纸板的材质影响蜂窝纸板缓冲性能。     

Paste Residence Time in a Spouted Bed Dryer. II: Effect of Spout Operational Conditions

Residence time distributions for an aqueous solution of 10% sodium chloride in a spouted bed dryer of inert particles were determined using the stimulus-response technique. Glass and polyethylene beads with diameters 2.6 and 3.4 mm were used as inert bodies in a cylindrical column of 14.0 cm diameter and 60° conical base. The effects of inert bodies load, air, and paste flow rates on the mean residence times and RTD were determined following 2³ factorial designs. The RTD could be correlated to the perfect mixing cell model with R² varying from 0.8684 to 0.9815. The mean residence times in CSBD varied from 10.8 to 13.9 and 10.7 to 13.3 min for glass and polyethylene beads, respectively. For both inert particles, mean residence times increased with bed height and decreased with paste feed rates. Also, terms of interaction among the factors were significant in some cases, showing a complex behavior of paste residence times. Equations obtained by response surface regression could predict mean residence times on glass and polyethylene beads with deviations lower than ±10%.     

Development,construction, and use of pneumometric tubes for measurement of steam flow in the steam lines of PVG-1000 at NPP

A system for the direct measurement of steam flow in steam lines after a steam generator, which utilizes a special design of pneumometric tubes and a computing unit that accounts for variation in steam pressure, has been developed to improve the quality of water-level regulation in the steam generators of VVéR-1000 power-generating units in the stationary and transitional modes. The advantage of the pneumometric tubes consists in their structural simplicity, high erosion resistance, and absence of irrevocable losses during measurement of steam flow. A similar measurement system is used at foreign NPP. The measurement system in question has been placed in experimental service at the No. 3 unit of the Balakovo NPP, and has demonstrated its worthiness. This measurement system can also be used to determine steam flow in the steam lines of NPP units with VVéR-1000 and VVéR-440 reactors, and PBMK-1000 power-generating units. __________ Translated from élektricheskie Stantsii, No. 3, March 2007, pp. 23–26.     

油田单井平均日产油量经济极限确定方法

从f(n,t)曲线的研究出发,得到了求解油田单井平均日产油量经济极限值的数学方程式,介绍了用曲线交汇法求解的过程,分析了油田月递减余率和原油销售价是影响油田单井平均日产油量经济极限的主要因素。该方法在油田开发调整方案的编制和油田开发规划部署工作中将起到一定的作用。     

电子辐照加速器大功率工频高压电源

文章介绍目前两种用于烟气脱硫加速器的不同形式直流高压电源，分析了它们各自的特点。针对它们存在的不足之处，提出了一种全新的倍压型桥式整流线路，并对此线路进行了理论推导和计算机模拟仿真。     

Drying Characteristics of Barley Grain Dried in a Spouted-Bed and Combined IR-Convection Dryers

A study was performed to determine the drying characteristics and quality of barley grain dried in a laboratory scale spouted-bed dryer at 30, 35, 40, and 45°C and an inlet air velocity of 23 m/s^-1, and in an IR-convection dryer under an infrared radiation intensity of 0.048, 0.061, 0.073, and 0.107 W cm^-2 at an air velocity of 0.5 m/s^-1. The results show that the first, relatively short, phase of a sharp decrease in the drying rate was followed by the phase of a slow decrease. The time of barley drying depended on temperature of inlet air in a spouted-bed dryer and on radiation intensities in an IR-convection dryer. Barley drying at 45°C in a spouted-bed dryer was accompanied by the lowest total energy consumption. The average specific energy consumption was lower and the average efficiency of drying was higher for drying in a spouted-bed dryer. The effective diffusivities were in the range 2.20-4.52 × 10^-11 m² s^-1 and 3.04-4.79 × 10^-11 m²/s^-1 for barley dried in a spouted-bed and in an IR-convection dryer, respectively. There were no significant differences in kernel germination energy and capacity between the two drying methods tested.     

Phase separation studies in RIM polyurethanes catalyst and hard segment crystallinity effects

Polyurethanes were prepared from pure 4,4′-diphenylmethane diisocyanate (MDI), 1,4-butane diol (BDO) or 1,2-ethane diol (EDO) and α,ω-hydroxyl poly(propylene oxide) (PPO) by reaction injection moulding (RIM). Hard segment (MDI + BDO or EDO) level was 45–50 wt%. The PPO had about 20% ethylene oxide copolymerized in at the chain ends to provide 80% primary OH end groups. M_n was varied from 2000 to 4000. Dibutyl tin dilaurate catalyst and mould temperature were varied. Dynamic mechanical, wide-angle X-ray, differential scanning calorimeter, molecular weight and tensile elongation measurements were made on the RIM polyurethanes. At low reaction rates (low catalyst or temperature) highly crystalline, well phase separated but low molecular weight polymers were produced. At high catalyst or temperature levels more poorly phase separated but high molecular weight, tough polymers resulted. Higher M_n PPO gave better phase separation and EDO gave higher melting temperatures. Preventing hard segment crystallinity by substituting asymmetric MDI or glycols resulted in phase compatibility.