Inhibition of microbial growth in ready‐to‐eat food stored at ambient temperature by modified atmosphere packaging

This study was undertaken to develop a modified atmosphere package to control microbial growth in ready‐to‐eat (RTE) products stored at ambient temperature. Ethanol and/or limonene associated with modified atmosphere (CO₂ : O₂ : N₂ = 30% : 5% : 65%) was used to inhibit the growth of total air‐borne microorganisms and Escherichia coli in RTE products stored at 25°C. The results indicated that 0.05% ethanol vapour in the headspace was effective to inhibit the growth of air‐borne microorganisms and E. coli at 25°C for 72 h in a model study, and the effectiveness was related to ethanol content. Both 73 ppm limonene and 0.05% ethanol vapour enhanced the bacteriostatic effect of modified atmosphere in RTE sushi roll products, and no off‐flavour was detected using this formulated gas; however, no significant inhibitory effect was observed for RTE cold noodle products. This study concludes that combinations of carbon dioxide, ethanol or limonene vapours are effective to inhibit microbial growth in RTE food at ambient temperature, and the outcome may be due to the hurdle effect. Copyright © 2003 John Wiley & Sons, Ltd.     

Operational aspects of adsorption air‐conditioner used in diesel locomotive

A locomotive cabin adsorption air‐conditioner has been equipped in #DF4B‐2369 locomotive; and has been successfully run for 2 years. It is powered by waste heat from the exhaust of the diesel engine. The influence on heat transfer is described by the equivalent heat transfer coefficient or thermal resistance of components inside the adsorber. The variation of adsorption capacity is expressed by a non‐equilibrium adsorption function. The dynamic heat transfer process of adsorption air‐conditioning system is treated with the lumped parameter method. Some typical running experimental results are present. The diesel engine rotating speed and locomotive speed influenced on the refrigeration system are discussed. The maximum mean refrigeration power is regarded as an objective function. Based on experiments and theoretical analysis, the running characteristics of the air‐conditioning system are optimized. Some techniques of performance improvement are suggested as well. Copyright © 2006 John Wiley & Sons, Ltd.     

Indoor Air Quality: Exploring Policy Options to Reduce Human Exposures

Deciding between the different policy approaches available for reducing human exposures to indoor pollutants is an exceptionally complex task. These options can range from waiting until more definitive information is available to enacting regulatory standards, with many variations in between. This paper presents some of the factors policy-makers must consider in establishing indoor air quality policies, and the role researchers should play in ensuring that indoor air policies are based on the best available scientific information.     

A comparison of leaf-spring with aircushion trailer suspensions in the transport environment

Packaging engineers need to be able to accurately determine the forces present in the shipping environment in order to protect packaged goods. The purpose of this study was to determine the vertical vibration levels measured in three separate truck-trailer suspension systems; conventional leaf-spring, conventional air-ride and damaged air-ride. The main conclusion reached in this study is that the air-ride suspension when maintained gives lower power density (PD) levels on all road surfaces studied. A damaged air-ride suspension and leaf-spring suspension are very similar in response frequencies, although the damaged air-ride produces higher vibration levels at lower frequencies.     

A Model for Through Drying of Tissue Paper at Constant Pressure Drop and High Drying Intensity

A mathematical model for through drying of paper at constant pressure drop was developed. The model is based on physical properties; hence, basis weight, pressure drop, drying air temperature, pore size distribution, initial gas fraction, and tortuosity are important input parameters to the model. The model was solved for different combinations of the variables basis weight, drying air temperature, and pressure drop corresponding to industrial conditions and the results were compared with data from bench-scale experiments. The simulations show that the drying rate curve is very sensitive to the air flow rate and that correctly modeling the correlation between pressure drop and air flow rate is the most important factor for a successful model for through drying. The model was tuned by adjusting the parameters initial gas fraction and tortuosity in order to give the best possible fit to experimental data. For a given basis weight and pressure drop, different drying air temperatures resulted in relatively constant values of the fitted parameters. This means that the model can well predict the effects of changes in drying air temperature based on a tuning of the model performed at the same basis weight and pressure drop. However, for a given basis weight, an increase in pressure drop yielded fitted parameters that were somewhat different; i.e., a lower initial gas fraction and a higher tortuosity, a change that increases the resistance to air flow. This implies that the correlation between pressure drop and air flow rate in the model does not quite capture the nonlinear relationship shown by the experiments.     

Properties and Performance of Cation-Doped Ceria Electrolyte Materials in Solid Oxide Fuel Cell Applications

Cation-doped CeO₂ electrolyte has been evaluated in single-cell and short-stack tests in solid oxide fuel cell environments and applications. These results, along with conductivity measurements, indicate that an ionic transference number of ∼0.75 can be expected at 800°C. Single cells have shown a power density >350 mW/cm². Multicell stacks have demonstrated a peak performance of >100 mW/cm² at 700°C using metallic separators.     

Thermodynamic Analysis of Various Dehumidifying Dryers for Wood

Typical methods of dehumidification of air circulating in the dehumidifying driers (indirect and direct cooler and partial exchange of the air) were analysed. Energy aspect of cooler operation was evaluated. The method for minimization of unit thermal energy consumption in a dehumidifying drier by the optimal selection of the cooler point was also given. Methods of the heat recovery of heat conveyed in a cooler lending to save energy (heat regeneration. expansion and compression of the air, a dehumidifier) were analysed. It was indicated that introduction of dehumidifiers into contemporary wood driers caused significant improvement of energy aspects of their operation     

空气压缩机无油润滑在山脚树矿的应用

山脚树矿有5台1966年上海生产的4L—20/8空气压缩机,运行很不经济,利用聚四氟乙烯合成材料制成活塞环,全部实现无油润滑运转,取得了良好的经济效益。     

Design and Characterization of the CLIMPAQ,Chamber for Laboratory Investigations of Materials,Pollution and Air Quality*

A test chamber has been developed in order to provide a small and simple emission testing facility capable of testing construction products in a climate where the important climatic parameters such as temperature, ventilation rate and air velocity can be varied independently around typical indoor values. The test chamber CLIMPAQ is made of panes of window glass. Other main surface materials are stainless steel and eloxated aluminium. The chamber has a volume of 50.9 litres and is designed to meet the requirements for quantifying air pollution. In this investigation human subjects acted as air pollution judges, and chemical characterization of the air pollution was carried out. Carpet, linoleum, wall paint and seal- ant were tested simultaneously in the CLIMPAQ and in four other chambers ranging from a full-scale chamber of 28 m³ to a field and laboratory emission cell of 3.5· 10^?5m³. Product ranking is the same in all chambers for the sensory measurements. Emission rates based on sensory measurements differ for all products less than 100 % except for tests in a 3-litre chamber where emission rates were higher. Chemical measurements differ up to approximately 10 times for the same product in different chambers. Deviations appear to be the result of different environmental parameters in the various chambers. Low air concentrations or high specific ventilation rates seem to increase emissions, while differences in air velocities and sink properties may also be the cause of differences in emission rates.