Kinetics of phenol oxidation in a trickle bed reactor over active carbon catalyst

The wet air oxidation of phenol over a commercial active carbon catalyst was studied in a trickle bed reactor (TBR) in the temperature and oxygen partial pressure ranges of 120–160 °C and 0.1–0.2 MPa, respectively. The performance of the active carbon was compared in terms of phenol and COD destruction. The weight change of active carbon due to reaction was also measured. Finally, oxic phenol adsorption isotherms were assessed in batch conditions at 25, 125 and 160 °C. In order to use the conversion data obtained from the TBR for a kinetic study, special care was taken to check the kinetic control in the TBR experiments. Several kinetic models including power law or Langmuir–Hinshelwood expressions were considered to describe the catalytic oxidation of phenol over active carbon. The simple power law model with first order dependence on both phenol and oxygen concentration predicted satisfactorily the experimental data not only over the entire range of operating conditions studied, but also outside its validity range. Copyright © 2005 Society of Chemical Industry     

The Danish Twin Apartment Study – Part II: Mathematical modeling of the relative strength of sources of indoor air pollution

Abstract This study deals with the modeling of air pollution in apartments from laboratory measurements of source strengths, using formaldehyde and Total Volatile Organic Compounds (TVOCs) as model pollutants. The sources in two test apartments were grouped into two: building-related sources and occupant-related sources. The measured source strengths and ventilation rates were used for the prediction of concentrations expected in the apartments. These predictions were compared to measurements in the apartment over 12 months. The conclusions were that the model predictions based on emission rates measured in the laboratory can be used to predict the long-term concentration of the two model pollutants in the apartments. Considering the measured differences in ventilation between the apartments, an occupant emission rate of between 0.2 and 0.3 mg/h/kg body weight could be estimated. Based on previous suggested limits of acceptable exposures of humans to VOCs, an acceptable average emission rate of VOCs from building materials in general was estimated to be about 30 (μ/m²/h. The modeling showed that during the first 200 days, building materials dominated the emissions. After this, sources relating to the occupants dominated. On average about half of the VOC pollution originated from the building materials.     

影响DT岩石粉状铵梯炸药爆速的因素探索

文章从ＤＴ岩石粉状铵梯炸药的原材料细度，复合油相，混药时间，投料顺序，混药药温，装药密度等方面，探讨了该炸药爆速的影响因素。     

Air entrainment in fresh concrete with PFA

The results of a study into the influence of PFA on air entrainment in fresh concrete are discussed It is shown that the required dosage of AEA to produce an air content of 5.5 ± 0.5% in a PFA modified concrete mix is two-six times that required in the corresponding neat OPC concrete mix. The dosage of a vinsol based air entraining agent (AEA) required appears to be directly related to the PFA content of the mix. Similar direct relationships were obtained with a range of different PFAs. The dosage of an AEA based on the salt of a fatty acid appears to be sensitive to both PFA and OPC contents. For the type of PFA used, the variability of measured air content or the amount of air retained after continued agitation both indicated that vinsol based AEAs show the highest variability whilst fatty acid based AEAs show low variability. The between batch variability of air content was significantly improved by the addition of PFA regardless of the AEA used.     

Synfuel development impacts— econometric modelling and policy analysis

The prospects for rapid near-term development of a synfuel industry in the USA have decreased, due to depressed world oil prices, synfuel project cost overruns, and the lukewarm support of the Reagan administration. Nonetheless, socioeconomic and environmental impact analysis studies can provide valuable information for determining the regional welfare effects of proposed projects. The author discusses the results of a regional econometric analysis of the synfuel projects planned for Western Kentucky, which focuses on environmental impacts, and reveals the inevitable trade-offs that would accompany synfuel development. Some policy issues are briefly reviewed, especially that of efficient energy pricing.     

A new alloy design concept for austenitic stainless steel with tungsten modification for bipolar plate application in PEMFC

The feasibility of a new alloy design concept utilizing the principle of ‘tungsten bronze effect’ is critically evaluated for the development of metallic bipolar plates for proton exchange membrane fuel cell (PEMFC). An austenitic stainless steel (ASS) is modified with W and La to improve the stability of the passive film in an acidic environment as well as to reduce the contact resistance by the tungsten bronze effect. The experimental ASS containing W and La was evaluated in a simulated PEMFC environment of H₃PO₄ and H₂SO₄ solutions at 80 °C, and the electrical property was evaluated by performing a contact resistance test. The test results show that the ASS modified with W and La has good passive film stability for corrosion resistance and low contact resistance. The X-ray photoelectron spectroscopy (XPS) analysis clearly suggests the possibility of the tungsten bronze effect from the change in valency state of W⁶⁺ to W⁵⁺ in the passive film formed on the modified ASS. The feasibility of a new alloy design concept utilizing the ‘tungsten bronze effect’ is well demonstrated; however, more study is highly required for the development of metallic bipolar plates of PEMFC.     

浅谈出口巴基斯坦铁路客车新型酚醛玻璃钢风道的研制开发

本文阐述了新型酚醛玻璃钢风道的成型工艺、开发过程，并与传统玻璃钢风道作了比较，论述了新型酚醛玻璃钢风道的优点，并对其应用前景和对铁路客车的设计思路的影响进行了探讨。     

Transformation of β-Ni(OH)2 to NiO nano-sheets via surface nanocrystalline zirconia coating: Shape and size retention

Shape and size of the synthesized NiO nano-sheets were retained during transformation of sheet-like β-Ni(OH)₂ to NiO at elevated temperatures via nano-sized zirconia coating on the surface of β-Ni(OH)₂. The average grain size was 6.42 nm after 600 °C treatment and slightly increased to 10 nm after 1000 °C treatment, showing effective sintering retardation between NiO nano-sheets. The excellent thermal stability revealed potential application at elevated temperatures, especially for high temperature catalysts and solid-state electrochemical devices.     

中央空调的水处理

本文扼要介绍了中央空调循环冷却水和冷冻水系统中常见的问题及其原因,并对冷却水和冷冻水的处理程序作了初步的阐述.     

Alkaline fuel cells: contemporary advancement and limitations

ZeTek Power recently introduced mass manufacturable and cost effective alkaline fuel cells on the market. Today's research is focused on further improvement both in terms of performance increase and cost reduction. This research is classically performed using small (4 cm²) experimental electrodes in the half-cell configuration. This allows the primary electrochemical losses in an anode or cathode to be determined independently. Additional performance losses occur when one integrates large electrodes into a module of 24 cells and in a stack comprised of many modules. By comparing the performance of half-cell experiments to that of modules, these losses can be distinguished and addressed. The information thus obtained, both for the small electrodes and in up-scaling is vital if one is to identify the key areas in which improvement is possible and where to focus future research. Furthermore, the identification of the losses in a module and system allows us to predict the final performance from half-cell measurements of a new laboratory scale experimental electrode.