Modeling of Diffusion in Capillary Porous Materials During the Drying Process

This paper presents a model of heterogenous diffusion in capillary porous materials during the process of drying. The governing heat and mass transfer equations have been established using the liquid as well as vapor flow. Two models have been presented. Model 1 does not consider the heat conduction while the model 2 has been established by considering the conduction. The developed models and the numerical solutions of the resulting differential equations can take into account the moisture and temperature dependent thermophysical properties of the product. All equations have been established in spherical coordinates but the programme written for the purpose of calculations can be used for other geometries also. Numerical calculations have been performed for gas concrete and tiles using model 1, while model 2 has been used for gas concrete only because of the lack of data for thermophysical properties of the tile. For gas concrete it was seen that conduction has only marginal effect on the drying process and the numerical predictions of the drying process were reasonably accurate.     

气体引射器流体动力特性实验研究

在实验装置上对气体引射器计算基本公式进行了实测验证，分析了理论特性曲线的可信度。通过实验，获得一些参数对引射器工况的影响规律。     

面向大批量定制生产的产品族设计技术综述

随着市场竞争的日益激烈,传统的大批量生产和单一的定制生产模式在激烈的市场竞争中已失去竞争优势,大批量定制生产模式,已成为制造业发展的必然趋势,它试图将大批量生产的高效率、低成本与定制生产灵活性、个性化的优势结合起来。开展产品族设计是实现大批量定制生产的有效途径。论述了大批量定制生产与产品族设计的关系,并对国内外有关产品族设计的文献进行了系统的整理和归类,提出了产品族设计系统框架,且对产品族设计的实现方法进行了介绍。     

高速往复式内燃机平衡轴低质量设计分析

分析了扇形和偏心圆两种平衡轴设计的要求以及平衡重低质量的设计原则。扇形平衡重半径及宽度应尽量大、夹角应尽量小。偏心圆平衡重的偏心圆半径应尽可能大 ,轴承半径应尽可能小。同样质量的扇形平衡重产生的平衡力比偏心圆平衡重要大。     

CMF300M355NU型质量流量计在油库汽车装车中的应用

介绍了质量流量计的工作原理有应用效果。这种新型质量流量计精度高，稳定性好，示值计量简便，可直接显示质量、流量、介质温度、密度等，维护量低，但必须正确安装、使用，才能发挥其应有的作用。     

Skeletal Isomerization and Inter—molecular Hydrogen Transfer Reactions in Catalytic Cracking

Bimolecular hydrogen transfer and skeletal isomerization the important secondary reac-tions among catalytic cracking reactions,which affect product yield distribution and product quality,Catalyst properties and operating parameters have great impact on bimolecular hydrogen transfer and skeletal isomerization reactions .Bimolecular hydrogen transfer activity and skeletal isomrization activity of USY-containing catalysts are higher thn that of ZSM-5-containing catalyst.Coke deposition on the active sites of catalyst may suppress bimolecular hydrogen transfer activity and skeletal isomer-ization activity of catlys in different degrees.Short raction time causes a decrease of hydrogen trans-fer reaction,but and increase of skeletal isomerization reaction compared to cracking reaction in catalytic cracking process.     

碱式苦味酸铅针刺药的应用研究

提出了以碱式苦味酸铅为主体的针刺药在组合点火管中的应用，并对其针刺药的点火性能及能量传递进行了讨论，阐明了此类针刺药良好性能和应用价值。     

Augmentation of boiling heat transfer from horizontal cylinder to liquid by movable particles

This paper presents a series of experimental results on a passive augmentation technique of boiling heat transfer by supplying solid particles in liquid. A cylindrical heater 0.88 mm in diameter is placed in saturated water, in which a lot of mobile particles exist, and the nucleate and film boiling heat transfer characteristics are measured. Particle materials used were alumina, glass, and porous alumina, and the diameter ranged from 0.3 mm to 2.5 mm. Particles are fluidized by the occurrence of boiling without any additive power, and the heat transfer is augmented. The maximum augmentation ratio obtained in this experiment reaches about ten times the heat transfer coefficient obtained in liquid alone. The augmentation ratio is mainly affected by the particle material, diameter, and the height of the particle bed set at no boiling condition. The augmentation mechanism is discussed on the basis of the experimental results. © 2001 Scripta Technica, Heat Trans Asian Res, 31(1): 28–41, 2002     

Application of annexation principle of thermodynamic property of In-Pb-Sb and In-Bi-Pb melts

Based on the principle of annexation and phase diagrams, the structural units of In-Pb-Sb and In-Bi-Pb melts were determined, and their calculating models of mass action concentrations were formulated. Calculated results agree well with practical values, which in turn show that the models deduced can reflect the structural realities of corresponding melts and the principle of annexation is applicable not only to some binary metallic melts, but also to ternary metallic melts.     

金属Be真空出气性能的测试

利用四极质谱计测试了国产金属铍材在 10 0℃～ 6 0 0℃不同温度下的真空出气成分及相对含量 ,实验得出铍的大量出气主要在温度 4 0 0℃～ 5 0 0℃之间 ,其放出气体的主要成分按放气量大小依次为H2 O ,CO2 ,N2 ,CO ,Ar和H2 ,利用限流小孔半定量的计算了铍材的出气量。