The influence of plastic properties on chip formation

A two-dimensional finite-element model of the chip formation process is used to study the influence of the material law determining plastic flow on chip formation of titanium alloys at high cutting speeds. For simplicity, friction and thermo-mechanical properties of the tool are neglected in the simulations. Titanium chips are strongly segmented and therefore especially suitable to study the role of segmentation for the cutting force and other cutting parameters. Of special interest is the influence of the thermal softening parameter in the material law. Increasing thermal softening leads to a drastic decrease in the cutting force and a corresponding increase in chip segmentation. A variation of the hardening exponent is also performed. It is shown that the simulation results can be understood by using adiabatic flow stress curves. The variation of the hardening exponent leads to strongly differing chip shapes, although the cutting force stays nearly constant. This shows that mean cutting forces should not be used as simulation verification parameters.     

V波段小型化低相噪频率综合器

本文研究了一种V波段超小型低相噪频率综合器,研制了L段捷变频频综、Ku波段取样锁相源、上变频组件、倍频器等四个小型化组件.为了得到较低的相位噪声和捷变频速度,本捷变频频综采用上变频-倍频方案,其中DRO PLS保证低相位噪声性能,L波段捷变频频综保证捷变频功能.该频综尺寸为100×80×30mm³,相位噪声低于-86dBc/Hz(1kHz),捷变频时间小于40μs,杂波抑制优于-60dBc.     

NUMERICAL INVESTIGATION ON MUD BED-GENERATION AND IMPACTING A WALL ALONG A SLOPE

In this paper mud was treated as the Bingham fluid. In staggered grids, two-dimensional incompressible Navier-Stokes equations for non-Newtonian fluid was solved by the MAC method. Numerical simulations were conducted on mud bed-generating phenomenon and mud impacting a wall along a slope. The distributions of free surface, pressure and velocity of mud and water were obtained. The results indicate that the computed layer thickness of mud bed almost equals the theoretically predicted value. Because of the differences in constitutive relationship, the distributions of free surface are different for water and mud. The distortion of water free surface is much more complicated.     

超音速燃气射流非定常波系的数值研究

根据ＭＵＳＣＬ格式的基本思想，对格式进行了部分修改，数值模拟了超音速燃气射流流场的结构和发展过程。给出了流场谐波系的变化趋势，得到了流场达到稳定状态的时间和稳定后的流动图形。     

给水流量控制系统仿真辅助设计

本文将给水流量系统规范化，给出静、动态数学模型，通过计算机仿真计算建立起设计参数Ｓ与系统特性间关系数据库，这些数据可用于控制系统辅助设计。本文还介绍了在Ｓ较小时自动补偿系统增益和时间常数的自适应控制方法并给出仿真结果。     

A modified flow enforcement technique for ATM networks

In ATM networks the requirement of providing the negotiated Quality of Service (QOS) needs an efficient flow enforcement technique that will result in preventive congestion control. A very effective technique is the Exponentially Weighted Moving Average (EWMA) method. In this paper, we have suggested improvements to the EWMA and call it the Enhanced EWMA (EEWMA). Simulation results show that the EEWMA is consistently better than the EWMA in most of the situations. We present comparisons of cell loss under various conditions. No theoretical analysis is presented.     

两相异步电动机变频调速装置

主要讨论对称两相变频器主电路的结构以及介绍一种简单实用的磁链轨迹控制技术．     

应用粒子动态分析仪研究水力旋流器流场

利用粒子动态分析仪(PDA),对水力旋流器内固相颗粒流场做了全面的测定,得出水力旋流器内固相颗粒的流态、浓度及粒度分布,为进一步查清水力旋流器的工作机理提供了重要理论依据。     

Modeling of Diffusion in Capillary Porous Materials During the Drying Process

This paper presents a model of heterogenous diffusion in capillary porous materials during the process of drying. The governing heat and mass transfer equations have been established using the liquid as well as vapor flow. Two models have been presented. Model 1 does not consider the heat conduction while the model 2 has been established by considering the conduction. The developed models and the numerical solutions of the resulting differential equations can take into account the moisture and temperature dependent thermophysical properties of the product. All equations have been established in spherical coordinates but the programme written for the purpose of calculations can be used for other geometries also. Numerical calculations have been performed for gas concrete and tiles using model 1, while model 2 has been used for gas concrete only because of the lack of data for thermophysical properties of the tile. For gas concrete it was seen that conduction has only marginal effect on the drying process and the numerical predictions of the drying process were reasonably accurate.     

微型无阀泵参数化结构设计及测试

 从理论计算和试验两方面研究了用于微流控化学分析芯片的微型无阀泵流动特性，初步建立了微型无阀泵流道结构的数学模型，重点讨论了结构参数的选取原则及相应的流动阻尼系数的计算方法． 通过试验验证了数值计算的可靠性，为微型无阀泵参数化设计及优化提供了理论依据及经验曲线．