Influence of the surface conditions on permeation in the deuterium–MANET system

The condition of the surfaces is of crucial importance for the deuterium permeation through materials. In this work a study of the surface constants for the adsorption (σk₁) and release (σk₂) of deuterium under different surface conditions on the martensitic steel DIN 1.4914 (MANET) has been carried out. The growth of an oxide surface layer (Cr₂O₃) of about 25–30 nm in a MANET sample, heat treated in an oxidizing environment, compared to the bare MANET that have a ‘natural' oxide of about 5 nm has provoked a reduction of both the permeation rate and the recombination coefficient (about 3 orders of magnitude). In addition, the permeation governing process has changed from diffusion-limited to surface-limited. The measurements of the permeation rate of deuterium were performed by a gas-phase permeation technique over the temperature range 574–746 K and for deuterium driving pressures in the range from 3 to 10⁵ Pa.     

Phase relations in the system ln-CulnS2

By DTA and x-ray diffraction the phase relations in the pseudobinary system In-CuInS₂ have been investigated. CuInS₂ hs a melting point of 1090° C and within this system there is a broad region of liquid immiscibility. A four phase invariant reaction exists at 633° C which is of the form: L₂ = L₁+ CuInS₂ + InS.     

多孔材料气体流量的简便计算

采用简便方法计算气体通过多孔材料的流量。当层流时，流量与压差按线性关系计算；紊流时，应按幂函数关系计算。本文提出了计算公式。     

Precipitation behavior of σ phase in fusion zone of dissimilar stainless steel welds during multi-pass GTAW process

The purpose of this study is to investigate the precipitation characteristics of σ phase in the fusion zone of stainless steel welds at various welding passes during a tungsten are welding (GTAW) process. The morphology, quantity, and chemical composition of the δ-ferrite and σ phase were analyzed using optical microscopy (OM), a ferritscope (FS), a X-ray diffractometer (XRD), scanning electron microscopy (SEM), an electron probe micro-analyzer (EPMA), and a wavelength dispersive spectrometer (WDS), respectively. Massive δ-ferrite was observed in the fusion zone of the first pass welds during welding of dissimilar stainless steels. The σ phase precipitated at the inner δ-ferrite particles and decreased δ-ferrite content during the third pass welding. The σ and δ phases can be stabilized by Si element, which promoted the phase transformation of σ→ϱ+λ₂ in the fusion zone of the third pass welds. It was found that the σ phase was a Fe−Cr−Si intermetallic compound found in the fusion zone of the third pass welds during multi-pass welding.     

Series resonant ZCS‐PFM DC‐DC power converter with high‐frequency high‐voltage transformer link for high‐power magnetron drive

This paper presents a single lossless inductive snubber‐assisted ZCS‐PFM series resonant DC‐DC power converter with a high‐frequency high‐voltage transformer link for industrial‐use high‐power magnetron drive. The current flowing through the active power switches rises gradually at a turned‐on transient state with the aid of a single lossless snubber inductor, and ZCS turn‐on commutation based on overlapping current can be achieved via the wide range pulse frequency modulation control scheme. The high‐frequency high‐voltage transformer primary side resonant current always becomes continuous operation mode, by electromagnetic loose coupling design of the high‐frequency high‐voltage transformer and the magnetizing inductance of the high‐frequency high‐voltage transformer. As a result, this high‐voltage power converter circuit for the magnetron can achieve a complete zero current soft switching under the condition of broad width gate voltage signals. Furthermore, this high‐voltage DC‐DC power converter circuit can regulate the output power from zero to full over audible frequency range via the two resonant frequency circuit design. Its operating performances are evaluated and discussed on the basis of the power loss analysis simulation and the experimental results from a practical point of view. © 2005 Wiley Periodicals, Inc. Electr Eng Jpn, 153(3): 79–87, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20126     

提高16Mn连铸坯控轧合格率

１６Ｍｎ连涛坯进行控轧时，按铸坯碳当量的上限和下限，分别采用两种不同的控轧制度。在邯钢中板分厂试轧的结果，轧材合格率均达到９６％以上，投产后轧材合格率达到９８％以上。     

GaAs FET辐射退化研究

低噪声ＧａＡｓ ＦＥＴ和功率ＧａＡｓ ＦＥＴ经中子辐射都未发生致命性的通或断失效，直流偏置伏态下，其失效模式仅仅表现为源漏饱和电流ＩＤＳＳ的退化降低，据此提出了ＩＤＳＳ退化失效与快中子注量φｎ之间的解析关键式ｌｎｙ＝ａ＋ｂｌｎφ。     

Kinetics of oxygen absorption in aqueous sodium dithionite solutions

The absorption and reaction of oxygen in aqueous alkaline solutions of sodium dithionite has been experimentally investigated in a novel gas-liquid contactor. The novel gas-lift bubble column contactor was used to study the kinetics over wide ranges of reactant concentrations, temperature, and pH. The oxygen-sodium dithionite reaction was found to be first-order with respect to dithionite in the range of dithionite concentration < 0.1 M, and second-order in the range of dithionite concentration > 0.1 M. The reaction with respect to oxygen was found to be zero-order for all dithionite concentrations. These results and experimental investigations of the effect of solution alkalinity and temperature on the reaction rate are consistent with previous findings obtained in different gas-liquid contactors. The results thus confirm the feasibility of using the gas-lift bubble column for the kinetics of gas-liquid reactions.     

Study on phase behavior–impact strength relationship of unsaturated polyester/polyurethane hybrid polymer network

The phase behavior of a hybrid polymer network (HPN) composed of poly[(propylene glycol maleate)-co-(propylene glycol phthalate)] crosslinked with styrene and polyester–urethane crosslinked with methylene-bis-ortho-chloroaniline was examined. The correlation between phase separation and impact strength of the HPNs is discussed. The composition of HPNs has an effect on their properties.     

A region-based selective optical flow back-projection for genuine motion vector estimation

Motion vector plays one significant feature in moving object segmentation. However, the motion vector in this application is required to represent the actual motion displacement, rather than regions of visually significant similarity. In this paper, region-based selective optical flow back-projection (RSOFB) which back-projects optical flows in a region to restore the region's motion vector from gradient-based optical flows, is proposed to obtain genuine motion displacement. The back-projection is performed based on minimizing the projection mean square errors of the motion vector on gradient directions. As optical flows of various magnitudes and directions provide various degrees of reliability in the genuine motion restoration, the optical flows to be used in the RSOFB are optimally selected based on their sensitivity to noises and their tendency in causing motion estimation errors. In this paper a deterministic solution is also derived for performing the minimization and obtaining the genuine motion magnitude and motion direction.