Growth of sculptured polymer submicronwire assemblies by vapor deposition

We have grown helical nanowire assemblies of parylene C, thereby demonstrating that polymeric sculptured thin films (STFs) can be fabricated by a combination of physical and chemical vapor deposition processes. The deposition method is explained in detail and electron micrographs of 200-400 nm size sculptured thin film of parylene are given. The shapes of the submicron and nanowire assemblies can be engineered so that the polymeric STF acts as a template for preferential attachment of biomolecules.     

薄板坯连铸浸入式水口结构数值模拟

使用有限元计算方法开展薄板坯连铸浸入式水口流场的研究 ,分别对水口不同浸入深度的流场分布、水口出口不同角度的流场分布进行计算。结果发现 :水口的浸入深度在 30 0mm时较为合理 ;水口的出口角度以R1 5、60°、45°为宜     

液相法制备纳米Fe_3O_4的研究进展

介绍沉淀法、微乳液法及水热法等纳米Fe3O4的制备方法,讨论了这些方法的优缺点。指出了沉淀法是目前制备纳米Fe3O4的最广泛应用的方法,而超声技术、交流电沉积与传统沉淀法的结合,是制备高纯度、小粒径、均匀分散的Fe3O4最有前途的方法。     

Surface modification of tetrafluoroethylene–perfluoroalkyl vinylether copolymer (PFA) by plasmas for copper metallization

Tetrafluoroethylene–perfluoroalkyl vinylether copolymer (PFA) sheet surfaces were modified with argon, helium, oxygen, and hydrogen plasmas. How the four plasmas modified the PFA sheet surfaces was investigated. All plasmas modified the PFA surfaces and at the same time initiated degradation of the PFA polymer chains. The balance between modification and degradation was strongly influenced by the magnitude of the discharge current in the plasmas. Efficiency of the plasmas in modification was hydrogen plasma > oxygen plasma > argon plasma > helium plasma. The modification involved defluorination of CF₂ carbons into CHF and CH₂ carbons and oxidation into O? CH₂, O? CHF, and O? CF₂ groups. The surface‐modification technique (a combination of hydrogen plasma treatment and silane coupling treatment) proposed in this study was applied for copper metallization of the PFA surface. The utility of the technique was confirmed. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1087–1097, 2002     

臭氧氧化处理法对聚丙烯表面涂装性的改良 Ⅳ.聚丙烯表面亲水性和涂膜剥离强度的关系

讨论了用臭氧氧化法对聚丙烯表面进行涂装性改良时,丙烯均聚物、乙烯-丙烯嵌段共聚物及无规共聚物表面以接触角表示的亲水性和涂膜剥离强度之间的关系。结果表明,当聚丙烯表面对水的接触角在84°附近时,可反应型涂料的涂膜剥离强度将出现最大值。在此也证明了涂膜的剥离破坏存在着接着破坏和凝集破坏两种机理,当接触角减小到84°及84°以上时,剥离发生在聚丙烯和涂层的界面上产生接着破坏;当接触角减小到84°以下时,剥离发生在聚丙烯的表面氧化层相中,产生凝集破坏。     

Low-temperature catalytic growth of carbon nanotubes under microwave plasma assistance

Various carbon nanotubes (CNTs) including aligned arrays, Y-branching and some other novel morphologies have been catalytically grown on anodic porous alumina template (APAT) and on the alumina-supported catalysts with methane (or benzene) as carbon source under microwave plasma assistance below 520 °C. The growth process could be simply operated since neither heating nor bias-voltage was applied to the catalysts or APAT. The results presented in this paper not only greatly richened the nanostructures of carbon family but also provided with a new technique path for synthesizing CNTs or some other nanostructures with the characteristics of low-temperature which has some special advantages or applications.     

化学气相沉积(CVD)炭/碳复合材料(C/C)研究现状

主要介绍了炭／炭复合材料（C／C）的化学气相沉积（CVD0制备方法及其影响因素，以及热解炭的组织与沉积机理。概括了VCD的基本方法，如等温法、压差法、热梯度法等。分析了温度、气流速率、气体浓度、预制体及孔隙的形状大小状况等对CVD过程的影响。列举了热解炭的组织，包括光滑层、粗糙层、各向同性体碳以及它们的变体，并对其生长特征及性能进行了较详细的描述。综述了热解炭的沉积机理，典型的有分子沉积、固态沉积、液滴沉积机理等。     

铬酸酐副产物硫酸氢钠的利用

对生产铬酸酐时副产的含铬硫酸氢钠的利用作了评论，介绍了8种方法，即，化学沉淀法、磷酸沉淀法、铬酸铬法、电解氧化法、过硫酸钠氧化法、制商品硫酸氢钠、酸泥制碱式硫酸铬、硫酸氢钠制碱式硫酸铬，其中以化学沉淀法、磷酸沉淀法和铬酸铬法应用最广。     

High resolution solid state 13C n.m.r. of butadiene grafted polypropylene

¹H dipolar decoupled ¹³C n.m.r. experiments with the aid of the magic angle spinning technique have been used to determine the graft content and the isomer content of the polybutadiene grafts in a graft copolymer with isotactic polypropylene.     

化学强化生物除磷工艺及设计

本文介绍了一种新的化学强化生物除磷工艺及其设计实例，与Phostrip侧流除磷工艺相比，其工艺优势在于所有污泥均经释磷和厌氧选择处理，通过化学沉积释放的磷，从而消除了在污泥处置过程中产生的磷释放回到污水处理系统的问题；所有回流污泥经厌氧选择处理，含有较高浓度聚磷菌类微生物，从而具有较高的除磷效率。