Characterization of EBPVD micro-layer composites and simulation of its internal stress state

Based on the basic operating principal and the technology characteristic of electron beam physical vapor deposition(EBPVD) technique, EBPVD was used to prepare the micro-layer composites. The effect on the substrate preheating temperature was taken into accounts and the finite element analysis package ANSYS was used to simulate the internal stress field and the potential displacement changing tendency. The results show that one of the most important quality factors on the judgment of micro-layer composites is the adhesion between the substrate and the deposition layers as well as among the different deposition layers. Besides the existance of temperature gradient through the thickness of layers, the main reason for the internal stress in micro-layer composites is the mismatch of various properties of the layer and the substrate of different thermal expansions and crystal lattice types. With the increase of substrate preheating temperature, the inter-laminar shear stress also takes on a tendency of increase but the axial residual stress decrease.     

试论双点后方交会简便公式

根据双点后方交会的图形特点和已知条件，列出了方程组，推导出了双点后方交会直接计算座标的简便公式，同时求出了精度计算公式，以供测量人员参考     

井巷掘进控制斜形炮孔钻孔精度的试验研究

井巷掘进爆破工程中，工作面按设计要求，布置各种斜形炮孔，利用量角器和垂直尺控制钎杆与工作面夹角，使炮孔钻孔精度与设计炮孔角度基本上符合，在生产中取得了良好的爆破效果．     

Determination of the width of the transition layer between the crystalline and amorphous zones in nylon 1010 by SAXS

The width of the transition layer between the crystalline and amorphous zones in nylon 1010 was determined by SAXS with point collimation and long-slit collimation, respectively. The width of the transition layer, E, was found to be 1.7 nm. The results show that the width of the transition layer is independent of crystallinity.     

Effect of type of processing on the microstructural features and mechanical properties of Al-Cu/SiC metal matrix composites

In this study, an aluminum based metallic matrix (Al-2wt.% Cu) was reinforced with SiC particulates using a conventional casting technique and a new disintegrated melt deposition technique. Microstructural characterization studies conducted on the samples taken from disintegrated melt deposition technique revealed a more uniform distribution of SiC particulates and good interfacial integrity between SiC particulates and metallic matrix when compared to the conventionally cast composite samples. Results of ambient temperature mechanical tests demonstrate an increase in 0.2% YS and ultimate tensile strength of samples taken from disintegrated melt deposition technique when compared with the unreinforced and conventionally cast composite samples. The results of microstructural characterization and mechanical testing were finally rationalized in terms of the nature of processing technique employed to reinforce Al-2wt.% Cu metallic matrix with SiC particulates.     

掺气减蚀设施水力计算的改进

结合小湾工程泄洪洞模型试验进行了11种挑跌坎型和6级流量的试验观测，据此提出了特别适用于大单流量条件的射流出射角修正式，提出了射流近底流速的选取原则.与实验资料对比证明本文计算方法有足够精度。     

溅射——气体——聚集共沉积法制备金属／金属（介质）复合团簇镶嵌薄膜

提出了溅射－气体－聚集共沉积制备金属／金属（介质）复合团簇镶嵌薄膜的新方法，并利用该方法成功地在方华膜衬底上制备了系列Ｆｅ／Ａｇ及ＣａＦ２复合团簇镶嵌薄膜样品。透射电镜分析结果表明，样品中Ｆｅ（Ｃｕ）团簇都较好地镶嵌于Ａｇ（ＣａＦ２）基质中，其结构为两种材料的多晶共存形态。进一步分析发现，与块材相比，Ｆｅ／Ａｇ样品中Ｆｅ团簇晶格常数呈现出不同程度的收缩，而Ｃｕ／ＣａＦ２样品中Ｃｕ团簇晶格常数则呈现出不同程度的膨胀。运用附加压力的模型对该现象进行了解释。     

套管固井质量问题及对策分析

从油田现场反应的情况出发，对调整井固井，尾管固井，大位移井套管固井和其他固井的质量问题进行了分析，针对各种问题产生的原因，提出了相应换解决办法。     

具有再生反馈雷达的角跟踪性能闭环测试

本文论述了用雷达跟踪目标最大角速度和角加速表征具有再生反馈雷达角跟踪性能的合理性,并论述了用单片机测试雷达跟踪目标最大角速度和最大角加速的方法。     

国外离子束系统（IBS）发展概况

综述了国外离子束刻蚀和沉积系统的研究进展，指出了离子束系统在半导体技术研究，开发和生产中的重要性。