Cure reaction for modified diallylbisphenol A/diaminodiphenylsulfone/bismaleimide

The glass‐transition temperature as a function of curing conversion for a modified diallylbisphenol A/diaminodiphenylsulfone/bismaleimide (BMI) resin was investigated at different temperature regimes and modeled using a modified Di Benedetto equation. Although the relationship between the glass‐transition temperature and conversion of the BMI system conforms to the Di Benedetto equation for α < 0.6 and at lower cure temperatures, at higher cure temperatures the results deviated significantly from the equation; thus, it was an inadequate model for the system. Fourier transform IR analysis showed that the major crosslinking reactions did not occur during cure for the modified BMI at and below 150°C. However, as the cure temperature was increased, the crosslinking reactions responsible for 3‐dimensional network structures became more dominant. At 190°C the C? N? C_stretch vibration of the uncured maleimide ring converted into succinimide rings in the curing process. Simultaneously, a decrease was observed for the absorbance bands of ? C? H_bending (maleimide). The higher cure temperatures induced a significantly faster initial crosslinking rate and also resulted in a shorter period of time after which further crosslinking was retarded, because the increase in the crosslinks also physically slowed further crosslinking activity. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 227–235, 2002     

LP-401磷化液在冷拔钢管生产中的应用

简单介绍了磷化液成膜原理。通过对比试用，得出了较为合理的工艺参数。实践证明，LP-401磷化液能够满足冷拔无缝钢管生产要求。     

Experimental evaluation of the strength distribution of E-glass fibres at high strain rates

A bimodal Weibull distribution function was applied to analyse the strength distribution of glass fibre bundles under tensile impact. The simulation was performed using a one-dimensional damage constitutive model. The results show that there were two concurrent flaw populations in the fracture process. The regression analysis using the bimodal Weibull distribution function was in good agreement with experiment.     

不锈钢绕带容器环板与绕带端头的焊接

本文通过焊接试验对奥氏体不锈钢绕带容器环板与绕带焊接工艺进行了研究分析,并得出了合理的焊接方法和工艺参数。     

轻钢结构浅析

轻钢结构作为一种新型结构在近几年发展很快，应用范围也日趋广泛。主要针对轻钢结构的特点，结合实际工程设计，对轻钢结构现状、发展进行了阐述和分析。     

高合金铁基烧结材料在轧钢导位中的应用研究

本文研究了高合金铁基烧结材料在轧钢导位中的应用。实验表明,通过粉末冶金液相烧结技术,可以获得具有优良综合性能的制品,材料密度ρ≥7.5 g/cm3,硬度≥55 HRC,抗弯强度≥1 000 MPa,冲击韧度αk≥3.9 J/cm2,满足了轧钢导位辊的工作要求。材料利用率可达95%以上、降低了制备成本。使用寿命是普通轧辊寿命的3~6倍,适用于线材和小型型材的轧钢生产。     

10000m^3天然气球罐用WEL—TEN610CF钢焊接冷裂纹敏感性

WEL-TEN610CF钢是日本新日铁公司生产的低裂纹敏感性高强钢,结合我国首台国产化10 000 m3天然气球罐用37 mm厚WEL-TEN610CF钢焊接性试验研究,对该钢焊接冷裂纹敏感性进行了综合评定,为其焊接工艺的制订提供了可靠的依据。     

低碳微合金钢中的晶内铁素体及组织控制

回顾和评述了晶内铁素体的发现、发展及其与组织控制的关系.介绍了晶内铁素体的形核机制和影响晶内铁素体形成的因素,讨论了晶内铁素体的三维形态和长大动力学,并从以上几方面分析了晶内铁素体对低碳微合金钢组织细化的重要作用和影响.     

用高梯度磁场净化轧钢废水

通过用高梯度磁场处理热轧厂废水的试验,得到了在试验条件下浊度(水中不溶物的含量)和铁的去除率,确定了最佳净化条件.在此条件下,能够有效去除废水中的不溶物和铁,经过处理的水质达到了工艺循环水的水质标准.     

500万t/a常减压蒸馏装置减压炉施工技术

结合华北石化500万t/a常减压蒸馏装置的核心设备即减压炉的施工实践,阐述了该工程的特点和总体施工程序。减压炉施工分为钢结构安装、炉管组焊和衬里施工3部分,文章分别从这几方面介绍了具体施工方法和关键技术。针对该炉体衬里在冬季施工的情况,通过分析设计采用的衬里材料的特性,对衬里结构进行了合理优化,并采取了有效的冬季施工措施,简化了施工程序,提高了施工速度,保证了质量,减压炉烘炉、试运、投产一次成功,并一直安全平稳运行。