INMARSAT 21世纪工程——全球个人移动卫星通信

本文概述INMARSAT 21世纪工程的规划及为实现这一规划,INMARSAT组织在本世纪末正在进行和即将进行的一系列卫星通信技术工作。着重阐述INMARSAT 21世纪工程的业务性能以及对三种卫星布局方案进行抉择的新动向。     

大系统分散鲁棒容错控制的进展及主要成果

综述了近２０年来关联大系统分散鲁棒容错控制的研究动态及取得的主要成果。说明了统一地研究分散鲁棒容错控制的必要性。在分散控制、鲁棒控制和容错控制研究领域内，分析了各种设计方法的主导思想及实质；指出了这些研究成果的意义与存在的问题。文中着重论述了分散、鲁棒、容错控制研究方法的发展途径。     

A delta transform approach to loop gain-phase shaping design of robust digital control systems

This paper addresses the existence of loop gain-phase shaping (LGPS) solutions for the design of robust digital control systems for SISO, minimum-phase, continuous-time processes with parametric uncertainty. We develop the frequency response properties of LGPS for discrete-time systems using the Δ-transform, a transform method that applies to both continuous-time and discrete-time systems. A theorem is presented which demonstrates that for reasonable specifications there always exists a sampling period such that the robust digital control problem has a solution. Finally, we offer a procedure for estimating the maximum feasible sampling period for LGPS solutions to robust digital control problems.     

Robust crossfeed design for hovering rotorcraft

Control law design for rotorcraft fly-by-wire systems normally attempts to decouple the angular responses using fixed-gain crossfeeds. This approach can lead to poor decoupling over the frequency range of pilot inputs and increase the load on the feedback loops. In order to improve the decoupling performance, dynamic crossfeeds should be adopted. Moreover, because of the large changes that occur in the aircraft dynamics due to small changes about the nominal design condition, especially for near-hovering flight, the crossfeed design must be ‘robust’. A new low-order matching method is presented here to design robust crossfeed compensators for multi-input, multi-output (MIMO) systems. The technique minimizes cross-coupling given an anticipated set of parameter variations for the range of flight conditions of concern. Results are presented in this paper of an analysis of the pitch/roll coupling of the UH-60 Black Hawk helicopter in near-hovering flight. A robust crossfeed is designed that shows significant improvement in decoupling perfomance and robustness over the fixed-gain or single point dynamic compensators. The design method and results are presented in an easily used graphical format that lends significant physical insight to the design procedure. This plant precompensation technique is an appropriate preliminary step to the design of robust feedback control laws for rotorcraft.     

An explicit finite difference method for finite-time observers

In this paper we present a numerical method for estimating the current state of a nonlinear control system. We use finite differences to discretize a modified version of the finite-time observer equations in James. The discretized equations are simple and easily programmed. The convergence and accuracy of the scheme is proved, and the scheme enjoys a number of important properties: availability of rate of convergence estimates, good robustness characteristics, and the ability to handle certain types of discontinuities in the observations. The major disadvantage is that the number of grid points required increases exponentially with the number of state dimensions.     

A method of identifying latent human errors in work systems

Work system improvements are implemented in various manufacturing processes to prevent problems caused by human errors. However, they are almost always applied to problems which have already occurred. This paper examines a method of identifying latent human errors existing within the work systems beforehand. A procedure for applying failure mode and effect analysis to this identification problem was defined based on over 1000 empirical errors: a work system decomposition criterion and fundamental error modes for listing latent human errors, and then applied to three practical manufacturing processes in order to evaluate its effectiveness.     

Energy use in controlled temperature marine aquaculture

Temperature control offers benefits in land‐based marine aquaculture: stock growth rates may be enhanced by heating in winter; mortality rates in summer may be reduced by cooling. However, if the plant is not well designed, temperature control may create very large energy demands. This paper describes the application of temperature control in abalone aquaculture in New Zealand, with a focus on energy considerations in plant design. An abalone farm using a semi‐closed water conditioning system is used as a case study for which an energy model, based on a heat pump system, is developed. The model is used to determine the impact of plant design and tank conditions on the economics of the operation. Copyright © 2002 John Wiley & Sons, Ltd.     

A robust adaptive pole‐placement controller without strictly positive real condition

This paper considers the adaptive pole‐placement control problem for system (1) with unmodelled dynamics η_n dominated by a small constant ε multiplied by a quantity independent of ε but tending to infinity as the past input, output, and noise grow. Using bounded external excitation and randomly varying truncation techniques, we give a design method of adaptive pole‐placement controller. It is shown that the closed‐loop system is globally stable, the estimation error for the parameter contained in the modelled part is of order ε, and the closed‐loop system under the adaptive pole‐placement control law is suboptimal in the sense of $$\mathop{\lim\sup}\limits_{{n\to\infty }}{1\over n}\mathop{\sum}\limits_{i=0}^n{\left({A^{*}(z)y_{n}‐L(z)C(z)w_{n}‐B(z)R(z)y_{n}^{*}}\right)^{2}{\leq}O({\varepsilon}^{2})+\gamma^{2}\mathop{\sum}\limits_{j=1}^q{b_{j}^{2}}}$$\nopagenumbers\end while the SPR condition used usually in other papers is replaced by a stability condition. Copyright © 2001 John Wiley & Sons, Ltd.     

Bandpass filters using periodically loaded combline resonators

A novel combline filter is proposed for cellular‐radio base stations. The Q‐factor is significantly improved. The eigenvalue equation is expressed with the single‐team approximation in the gap region of the combline resonator. A two‐pole combline filter is designed. The calculation, simulation, and experiment results are presented and are in good agreement. © 2005 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2006.     

Specification methods for material-handling control algorithms in flexible manufacturing systems

Good methods are needed to specify, test, and debug material-handling control logic. This article surveys a number of representative methods for defining and describing control algorithms for programmable material-handling equipment used in flexible manufacturing systems. The methods are evaluated with regard to their suitability for communication between people and as bases for interfaces to automatic program generators. It is concluded that no single method is entirely satisfactory. Three methods (position diagrams, function block diagrams, and operation networks) have potential to be combined into an effective hybrid approach that minimizes the need for the user to switch between various conceptual models.