冷弯型钢纵向变形的理论分析及计算

对冷弯型钢的纵向变形过程进行了力学分析，得到了变形微分方程，求得了转动角的理论公式，并对其变形形状进行了分析计算。     

34CrMoV结构钢动态再结晶行为研究

应用Gleeble-1500热模拟实验机进行等温压缩试验,研究了变形工艺参数对34CrMoV结构钢动态再结晶行为的影响.结果表明,其流变应力随变形温度升高而降低,随应变速率提高而增大;随着应变速率的降低,应变量的增加和变形温度的升高,动态再结晶速度加快且奥氏体晶粒得到细化.     

A Study of Surface Deformation during Wire‐Rod Rolling of High Speed Steels using Experimental and Computational Techniques

The evolution of surface defects during shape rolling of high‐speed steel billets is studied using longitudinal surface defects prepared by machining and welding. The reduction of the defects during rolling in a production mill is compared to the total area reduction of the billets. Samples are collected after pass 4, 6, 8, 14, 19 and the final pass, 28, representing the finished 5.5mm wire. By inspecting the cross sections, the rotation of the billets from pass to pass is evaluated. Results from FE simulations on solid billets are compared to the experimental results. Generally, simulations predict less reduction than observed experimentally. In most cases cracks reduce most effectively followed by carbon steel welds and stainless steel welds.     

Cyclic X-Y mechanical tests: A new method to perform in situ reversed-deformation experiments in the high-voltage electron microscope

There has been, in the past, only limited success with in situ cyclic or reversed plastic deformation tests in the transmission electron microscope (TEM). This is probably partly due to problems associated with buckling of the foil when an applied tensile or shear stress is reversed. Mechanical analysis shows that dislocation movement can be reversed by tensile stressing in alternating perpendicular directions (i.e., 90° rotations of a tensile stress); thus buckling of the foil can be avoided. A design for performing such X-Y in situ TEM tests is presented, with observations that demonstrate its feasibility.     

The intervalley X6→Γ6, L6 scattering time in GaAs measured by ultrafast pump-probe infrared absorption spectroscopy

A direct measurement of the dynamics of electrons in the X₆ valley for a GaAs crystal by time-resolved absorption spectroscopy is reported for the first time. IR picosecond probe pulses were used to monitor the growth and decay of the population in the X₆ valley subsequent to excitation by a 527 nm pump pulse. The intervalley X₆→Γ₆, L₆ scattering time t_x of 0.70 ± 0.50 ps is determined and the crossection for the X₆→X₇ transition is estimated to be 1.8 × 10⁻¹⁶ cm².     

现浇混凝土构件与砌体接触面收缩和温度应力裂纹的探讨

分析讨论了建筑物由于收缩及温度应力而引起的过纹，提出了在设计施工中应考虑的问题和采取的防止措施。     

GCr15控制轧制新工艺的模拟研究

用热扭转试验机，实现了热变形模拟轴承钢控制轧制工艺。研究了形变过程中所发生的静态和动态软化过程，观察了形变后的组织，证实在生产过程中实现的可能性，为在生产中推广使用提供了科学依据。     

表面微观屈服应力与表面变形研究

本文对表面微观屈服应力的测量与计算方法及表面变形的应变曲线进行了分析研究。结果表明，表面微观屈服应力与加载方式有关；表面变形的应力应变曲线具有双线性特征。     

210 t转炉连接装置的有限元分析及强度校核

利用ANSYS Workbench对某210 t转炉整体模型的三种极限工况进行有限元分析,得到转炉系统的应力分布和总变形,同时得到连接装置各个零部件的应力分布,找出零部件的最大应力值及所处位置,并结合有限元计算结果对各个零部件进行强度校核.结果表明连接装置的强度满足要求。     

反应堆堆芯围筒结构热流固耦合热变形分析

针对反应堆堆芯围筒热流固耦合问题,采用三维有限元法研究堆芯围筒的热变形.考察ANSYS的三维实体热单元SOLID 70,三维实体单元SOLID 45,三维表面热效应单元SURF 152和三维热-流耦合管单元FLUID 116等单元类型的特点和实用性.建立堆芯围筒、吊篮和冷却剂的温度分析有限元模型：堆芯围筒和吊篮采用SOLID 70,结构表面与冷却剂的对流传热表面采用SURF152,堆芯围筒与吊篮之间冷却剂采用FLUID 116.采用SOLID 45建立堆芯围筒有限元模型,根据得到的堆芯围筒、吊篮和冷却剂的温度场结果分析堆芯围筒热变形.结果表明,在考虑堆芯围筒及吊篮固体和流体的交叉耦合的基础上,采用三维有限元法能比较客观地模拟反应堆堆芯处的复杂运行环境.