新世纪我国压铸业与国际接轨的思考

针对中国压铸行业的现状和存在的问题 ,以及当前的机遇和面临的挑战 ,论述了中国压铸工业进入 2 1世纪所面临的新形势及应采取的对策     

莱钢中小型连轧生产线技术装备状况及改进

介绍了莱钢引进的具有 90年代国际先进水平的中小型型钢连轧生产线的工艺、设备特点及主要技术参数 ,以及对原机械设备、电气及工艺备件的改进和新产品开发情况 ,均取得良好效果。     

露天矿半连续工艺技术应用现状及发展前景

介绍了露天矿半连续工艺技术国内外应用现状、研究成果以及发展趋势。     

连铸机油缸成套密封件国产化

本文论述了冶金行业中连铸机油缸密封件国产化的一些技术参数，同时也介绍了洪格尔型组合密封及夹布V型圈组合密封的使用特点。     

In-situ composite Cu-Cr contact cables with high strength and high conductivity

In order to develop a new type of contact cable with high strength and high electrical conductivity, Cu-Cr alloy series were selected as materials and Cu-Cr alloy castings were produced by means of directional solidification continuous casting (DSCC) process. The results show that the fibrillar strengthening phase, 13-Cr, orderly arranges among the copper matrix phase along the wire direction; and a microstructure of in-situ composite forms, which retains the basic property of good conductivity of the copper matrix and meanwhile obtains the strengthening effect of [3-Cr phase. The production technology as well as the mechanical property, electrical property, and synthetic property of the in-situ composite contact cables was discussed.     

用于千兆以太网基带铜缆接收器均衡的甚高频自适应 连续时间Gm-C 二阶带通滤波器的研究和设计

本文设计了用于千兆以太网基带铜缆接收器均衡的甚高频自适应连续时间Gm-C二阶带通滤波器。基于最陡梯度下降算法，带通滤波器的零点在57－340MHz的频率范围内可以自适应地调节，中心频率为1.278GHz。通过外接电阻伺服环路，滤波器中跨导转换器的跨导值不受工艺偏差和温度变化的影响，采用CSMC－HJ0.6μm CMOS工艺器件模型，用Cadence Spectres仿真器仿真了设计的自适应滤波器电路，仿真结果验证了设计原理和设计的电路。系统的最长学习时间为880个参考时钟周期。     

Continuous precipitation of calcium sulfate dihydrate from waste sulfuric acid and lime

Precipitation of calcium sulfate dihydrate, gypsum, from (i) a pure sulfuric acid/lime suspension and (ii) a waste sulfuric acid/lime suspension in a continuous pilot plant in the temperature range from 40 °C to 80 °C was studied. It was observed that in the case of waste sulfuric acid with a high content of Mg²⁺ and Fe²⁺ ions, several hours after the beginning of the precipitation, partial dissolution of the product and modification of the crystals from needle‐ and plate‐like to agglomerated structures occurred. It is suggested that the secondary changes occur due to the increased concentration of Mg²⁺ and Fe²⁺ ions in the reactor. Below 60 °C, and above 70 °C plate‐like and needle‐like single crystals respectively were formed. The mean size (d₅₀) of the crystals was found to increase with increasing temperature and decrease with the initial concentration of lime. Gypsum produced between 70 °C and 80 °C is suitable for further processing for construction plaster. In a precipitation process with pure sulfuric acid only single perfect needle‐like crystals occurred. Copyright © 2005 Society of Chemical Industry     

薄板坯连铸连轧流程Ti微合金化高强钢开发与应用

在薄板坯连铸连轧流程上，经过对Ti微合金化技术研究，有效解决了Ti微合金化强度性能波动大的问题，开发出屈服强度450～700MPa高强钢。对试制钢组织性能和工业应用分析研究，表明该产品通板性能良好，通板强度差30MPa左右；成形性能良好，d=0时冷弯测试全部合格；同时还具有良好焊接性能，焊接后，强度波动较小，均在母材部位断开；试制钢显微组织为珠光体和铁素体，晶粒均匀细小，平均尺寸为4～8／μm；实物质量满足集装箱和汽车制造行业要求，具有广阔市场前景。     

广州中信商城地下连续墙施工工艺

本文介绍了广州中信商城地下连续墙的施工工艺。该工艺采用膨润土制浆配制方式，施工质量高，效果好。     

旋转导向钻井偏心稳定器横向振动研究

旋转导向钻井偏心稳定器横向振动研究是国家863“可控(闭环)三维轨迹钻井技术”课题研究的部分内容。选取偏心稳定器的心轴作为研究对象,以偏心稳定器心轴连续梁系统的横向振动模型受力分析为基础,根据课题研究中所设计的心轴结构形式,建立了与实际情况较为接近的三铰支点的连续梁系统横向振动方程;并分析了偏心稳定器横向振动对钻井工具和钻具系统的影响,为合理进行心轴设计以及偏心稳定器样机在现场的正确使用和钻井参数的合理选择,提供了科学的理论依据和实用的计算方法。计算实例表明,当钻压范围选择在80~250kN时,215.9mm井眼钻进中的确存在19~20、61~63、162~163r/min前三阶横向共振转速区间,因此在选择钻井参数时应通过钻压与转速的配合,尽可能避开横向共振转速,以保证下部钻具组合系统及作业安全。