Heat Transfer Analysis for Gas-to-Liquids Transportation Through Trans Alaska Pipeline

Gas-to-liquids (GTL) technology involves the conversion of natural gas to liquid hydrocarbons. In this article, theoretical studies have been presented to determine the feasibility of transporting GTL products through the Trans-Alaska Pipeline System (TAPS). To successfully transport GTL through TAPS, heat loss along the route must be carefully determined. This study presents heat transfer and fluid dynamic calculations to evaluate this feasibility. Because of heat loss, the fluid temperature decreases in the direction of flow and this affects the fluid properties, which in turn influence convection coefficient and pumping power requirements. The temperature and heat loss distribution along the pipeline at different locations have been calculated. Fairly good agreement with measured oil temperatures is observed. The powers required to pump crude oil and GTL individually, against various losses have been calculated. Two GTL transportation modes have been considered; one as a pure stream of GTL and the second as a commingled mixture with crude oil. These results show that the pumping power and heat loss for GTL are less than that of the crude oil for the same volumetric flow rate. Therefore, GTL can be transported through TAPS using existing equipment at pump stations.     

Electrochemical mass transfer between an impinging jet and a rotating disk in a confined system

This paper presents the mass transfer results from an impinging liquid jet to a rotating disk. The mass transfer coefficients were measured using the electrochemical limiting diffusion current technique (ELDCT). Rotational Reynolds number (Re_r) in the range of 3.4 × 10⁴–1.2 × 10⁵, jet Reynolds number (Re_j) 1.7 × 10⁴–5.3 × 10⁴ and non-dimensional jet-to-disk spacing (H/d) 2–8 were taken into consideration as parameters. It was found that the jet impingement resulted in a substantial enhancement in the mass transfer compared to the case of the rotating disk without jet.     

管内装元件强化传热的技术经济评价

提出了一种管内装元件强化传热的技术经济评价方法，此方法综合考虑了强化换热器管内传热膜系数的提高和管内流体阻力的增大，与普通的管壳式换热器相比，所带来的投资费用和使用费用变化，这个变化量可用净现值增量△NPV来表示。根据△NPV值来评价强化传热技术，从而为强化传热技术的开发和推广及进行决策提供指导。     

Method to Characterize the Air Flow and Water Removal Characteristics During Vacuum Dewatering. Part II—Analysis and Characterization

This is part II of a study reported earlier on a method to characterize the air flow and water removal characteristics during vacuum dewatering. This article presents experimental data and analysis of results from the use of a cyclically actuated vacuum dewatering device for removing moisture from wetted porous materials such as paper with the intermittent application of vacuum and accompanying air flow though the material. Results presented include sheet moisture content as a function of residence time and hence water removal rate under a variety of process conditions. Also, experimental results on air flow through the wet porous structure and hence the role and importance of air flow during vacuum dewatering are presented. Vacuum dewatering process conditions include exit solids content between 11 and 20% solid under applied vacuum conditions of 13.5 to 67.7 kPa (4 to 20 in. Hg). Regression analysis indicated that the exit sheet moisture content exhibited a nonlinear relationship with residence time with exit solids reaching a plateau after a certain residence time. Final moisture content correlated linearly with the average overall flow rate of air through the paper sample and the basis weight of the material.     

Synthesis and characterization of functional gradient copolymers of glycidyl methacrylate and butyl acrylate

Epoxy-functional spontaneous gradient copolymers of glycidyl methacrylate (G) and n-butyl acrylate (B) were synthesized via atom transfer radical polymerization (ATRP). The copolymerization reactions were carried out in toluene solution at 70 °C, using methyl 2-bromopropionate (MBrP) as initiator and copper chloride with N,N,N′,N′′,N′′-pentamethyldiethylenetriamine (PMDETA) as the catalyst system. The kinetic behaviour of the statistical copolymerizations was studied in a wide composition interval with molar fractions of G ranging from 0.10 to 0.75. The synthesized copolymers were characterized by size exclusion chromatography (SEC) and nuclear magnetic resonance (NMR) spectroscopy. ¹H NMR was employed to determine the copolymer composition, demonstrating the gradient character of the copolymers along the main chain in the whole monomer conversion interval. Apart from this, the sequence distribution and stereoregularity were analyzed. These microstructural experimental data agreed well with those calculated from Mayo-Lewis terminal model (MLTM) and a Bernoullian statistic with an isotacticity parameter of σ_G = 0.28 and a coisotacticity parameter of σ = 0.30.     

Analysis of Multiphase Flow and Heat Transfer: Pressure Buildup in an Unsaturated Porous Slab Exposed to Hot Gas

This study develops a mathematical model for coupled heat and mass transfer in an unsaturated porous slab exposed to a flowing hot gas. Effects of the initial saturation conditions on associated variables, i.e., total pressure, temperature, moisture content, and multiphase flow, are studied. The Newton-Raphson method based on a finite volume technique is applied. This study emphasizes the influence of initial saturation level and gravitational effect in heat and multiphase flow phenomena associated with this system. Gravity enhances the downward flow of liquid within the porous slab. Pressure buildup occurs near the interface between the wet and the dry zone. However, it appears that the order of magnitude to the total pressure is small. This study explains the fundamental mechanism of multiphase flow that involves heat and mass transfer in a heated unsaturated porous slab.     

Passive cooling in a low-energy office building

In office buildings, the use of passive cooling techniques combined with a reduced cooling load may result in a good thermal summer comfort and therefore save cooling energy consumption. This is shown in the low-energy office building ‘SD Worx’ in Kortrijk (Belgium), in which natural night ventilation and an earth-to-air heat exchanger are applied. In winter, the supply air is successively heated by the earth-to-air heat exchanger and the regenerative heat exchanger, which recovers the heat from the exhaust air. In summer, the earth-to-air heat exchanger cools the ventilation air by day. In addition, natural night ventilation cools down the exposed structure which has accumulated the heat of the previous day. In this article the overall thermal comfort in the office building is evaluated by means of measuring and simulation results. Measurements of summer 2002 are discussed and compared to simulations with a coupled thermal and ventilation simulation model TRNSYS-COMIS. The simulations are used to estimate the relative importance of the different techniques. The evaluation shows that passive cooling has an important impact on the thermal summer comfort in the building. Furthermore, natural night ventilation appears to be much more effective than an earth-to-air heat exchanger to improve comfort.     

Upper bounds for solar thermophotovoltaic efficiency

The main components of thermophotovoltaic (TPV) devices are the primary lens (or mirror), the absorber, the PV cell, and a photon recuperator system. A theory integrating all these components is used in this paper to analyse a particular type of TPV device (plane disk absorber and PV cell). The TPV efficiency is maximized by using three optimization parameters, namely absorber, PV cell temperatures, and cell voltage. Almost ideal operation conditions are envisaged and upper bounds are obtained for the TPV efficiency. They are strongly dependent on PV cell bandgap and radiation concentration. Preliminary results suggest the existence of an optimum solar radiation concentration ratio. The improvement in thermal design quality allows the usage of PV cells based on wide bandgap semiconductors.     

60Si2Mn合金钢发蓝泛红的分析研究

本文探讨了60Si2Mn合金钢发蓝原理，针对其膜层泛红问题，分析了热处理、表面前处理、发蓝及浸油等过程对发蓝质量的影响，由此采取了相应的技术措施，生产实践证明发蓝质量稳定，生产效率明显提高。