Independently controllable dual‐band microstrip bandpass filter using quadruple‐mode stub‐loaded resonator

In this article, a quadruple‐mode stub‐loaded resonator (QM‐SLR) is introduced and its four modes are excited using a simple approach, which can provide a dual‐band behavior. By changing the length of the loaded stubs, independently tunable transmission characteristics of the proposed quadruple‐mode stub‐loaded resonator were extensively described for filter design. Moreover, microwave varactors were adopted to represent the length variation of the loaded stubs for the dual‐band tunability. The equivalent circuit modeling of the open stub with microwave varactor was given and discussed. Then, adopting the compact quadruple‐mode stub‐loaded resonator with three varactors, an independently controllable dual‐band bandpass filter (BPF) was designed, analyzed, and fabricated. Its separated bandwidths and transmission zeros can be tuned independently by changing the applying voltage of the microwave varactors. A good agreement between simulated and measured results verified the design methodology. The proposed filter possesses compact size, simple structure, and excellent dual‐band performances. © 2016 Wiley Periodicals, Inc. Int J RF and Microwave CAE 26:602–608, 2016.     

A novel compact planar ultra‐wideband antenna with dual band‐notched characteristics

A novel planar ultrawideband monopole antenna with dual notched bands is presented. The antenna mainly consists of a radiation patch and a modified ground plane. To realize dual band‐notched characteristics, a U‐shaped stub embedded in the rectangular slot of the radiation patch and a novel coupled open‐/shorted‐circuit stub resonator are used on the backside of the substrate. The bandwidth of the dual notched bands can be controllable by adjusting some key parameters. The simulated and measured results indicate that the proposed antenna offers a very wide bandwidth from 2.6 to 18 GHz with Voltage Standing Wave Ratio (VSWR) < 2, except the dual notched bands of 3.3–3.7 GHz (World Interoperability for Microwave Access [WiMAX]) and 5.15–5.825 GHz (Wireless Local Area Network [WLAN]). Furthermore, good group delay and stable gains can be achieved over the operating frequencies. © 2014 Wiley Periodicals, Inc. Int J RF and Microwave CAE 25:48–55, 2015.     

Novel slotted stepped‐impedance resonator and its application to compact and high performance bandpass filter and diplexer design

By etching slots in the low‐impedance section of the conventional stepped‐impedance resonator, a novel slotted stepped‐impedance resonator (SSIR) is proposed. As two examples, a fourth‐order bandpass filter (BPF) operating at 1 GHz with a size of 0.078 λ_g × 0.062 λ_g and a miniaturized diplexer operating at 0.9/1.57 GHz with a size of 0.054 λ₀ × 0.086 λ₀ are designed based on the proposed SSIR. The fabricated BPF exhibits a high selectivity and a wide ?30 dB rejection upper stopband from 1.13 f₀ to 6.52 f₀, while the fabricated diplexer has up to ?60 dB output isolation. © 2012 Wiley Periodicals, Inc. Int J RF and Microwave CAE, 2013.     

一种新型环谐振器在带通滤波器中的应用

本文设计了一种新型四分之一波长侧耦合线双模环形谐振器。根据滤波器的指标要求：中心频率、带宽、传输零点频率以及通带插八损耗,综合设计得出谐振器参数。将这种谐振器应用到传统的平行耦合微带线带通滤波器中,大大提高了滤波器的频率选择性。     

微悬臂梁谐振式气体传感器研究进展

微机械谐振式传感器已经成为微型机电系统(MEMS)领域的研究热点。讨论了微悬臂梁谐振式气体传感器的工作原理,介绍微悬臂梁表面修饰的关键技术、主要方法和基于微悬臂梁的谐振式气体传感器领域的研究状况以及近五年以来该领域的研究进展,并对基于微悬臂梁的谐振式气体传感器的发展方向和应用前景做了展望。     

谐振腔蒸汽湿度测量系统的补偿研究

在微波单腔测量流动湿蒸汽的系统中,影响蒸汽湿度测量准确性的因素比较多。分析了谐振腔热膨胀引起的频率漂移、水膜厚度引起谐振频率的变化以及频率测量环节引起的测量误差,并分别介绍了相应的补偿措施。通过对各环节的补偿,可以有效地提高蒸汽湿度的测量精度。     

温度效应造成的半球谐振陀螺振幅和测角误差因素分析

在半球谐振陀螺工作的过程中,环境温度的变化是不可避免的。温度的变化影响谐振子尺寸变化,导致陀螺产生热漂移。根据振幅检测原理,推导温度效应误差的数学表达式,分析它对测量结果的影响,这对选择合适的补偿算法以消除温度效应误差有一定的指导意义。     

石英谐振器的电路设计与力频特性的研究

根据共模抑制原理,基于一种单基多电极石英晶体谐振器的结构,设计了一种新型的信号处理电路,这种电路将同一晶体基片上不同位置的谐振器对应的谐振频率作混频处理,然后采用差频、求和,最后倍频输出的方式输出,描述了各部分电路的设计.在分析石英谐振器的能限理论及力一频特性的基础上,用此方案设计的电路进行AT切同基三电极石英谐振器的力一频特性实验,记录了不同加力方式下的力一频特性,结果显示这种电路优化了力一频系数,线性度良好.在一定的加力方式下,经求和电路处理后的力一频系数可达139.72 Hz/N.     

一种测量微波谐振腔品质因数的改进方法

提出了一种测量谐振腔Q值的改进方法,即标量反射系数平均法.该方法根据微波谐振腔在谐振点附近的|г(f)|曲线,采用扫频的方法得到其△|г|(dB)从0(dB)到|г0|(dB)对应的△f,进而推算得到其对应的Q值曲线.选取其中一段受误差影响较小的Q值曲线,采用拟合平均的方法得到其准确可靠的无载品质因数.此方法很好地解决了由于外电路的耦合给传统方法带来的测量误差的问题,并对自由选点测量Q值法在选点方面有一定的参考价值.     

采用阶梯 T 型谐振器的双陷波 UWB 滤波器

为有效抑制印度国家卫星通信C频段和X卫星频段对超宽带通信系统的干扰,提出了一种新型双陷波超宽带滤波器。该滤波器采用阶梯T型多模谐振器(multimode resonator, MMR)与缺陷地结构(defected ground structure, DGS)的交趾耦合,实现超宽带特性。采用非对称耦合线及在MMR两侧耦合分裂环谐振器的方法,分别在6.67～7.06 GHz, 7.47～7.57 GHz两个频段内产生陷波。实测结果与仿真结果吻合较好,该滤波器的通带范围为3.03～11.50 GHz, 3 dB带宽达到123%,插入损耗仅有0.87 dB,两处陷波中心频率分别在6.87 GHz和7.52 GHz,陷波深度均大于20 dB,且整体尺寸紧凑,仅有16 mm×8 mm大小。