High‐pressure processing effects on the mechanical,barrier and mass transfer properties of food packaging flexible structures: a critical review

Food products can be high‐pressure processed (HPP) either in bulk or prepackaged in flexible or semi‐rigid packaging materials. In the latter case the packaging material is subjected, together with the food, to high‐pressure treatment. A number of studies have been performed to quantify the effects of high‐pressure processing on the physical and barrier properties of the packaging material, since the integrity of the package during and after processing is of paramount importance to the safety and quality of the food product. This article reviews the results of published research concerning the effect of HPP on packaging materials. Copyright © 2004 John Wiley & Sons, Ltd.     

三峡工地高压供电线路故障判断方法的探讨

高压供电设备故障特别是输电线路的高压接地故障对工地的影响是相当大的。由于接地故障为隐性故障，没有明显的物理现象，且若是长期接地可能会发展成较为严重的两相或三相短路故障，使系统解列运行直至崩溃；由于工地流动人员较多，还易造成电击事故。利用高压一相接地时在线路中产生零序电压这一特性来迅速判断和切除接地的用电设备，可以保证各项施工的顺利进行。     

高放废液中^147Pm的测定

建立了高放废液中~(147)Pm的测定方法。用HDEHP萃取稀土,再用HDEHP萃淋树脂柱分离AM和稀土。然后用高效液相色谱法将~(147)Pm从Eu、Ce等其它稀土中分离出来,用液体闪烁法测量~(147)Pm的放射性活度。     

Syllables as processing units in handwriting production.

This research focused on the syllable as a processing unit in handwriting. Participants wrote, in uppercase letters, words that had been visually presented. The interletter intervals provide information on the timing of motor production. In Experiment 1, French participants wrote words that shared the initial letters but had different syllable boundaries. In Experiment 2, French- and Spanish-speaking participants wrote cognates and pseudowords with a letter sequence that was always intrasyllabic in French and intersyllabic in Spanish. In Experiment 3, French-Spanish bilinguals wrote the cognates and pseudowords with the same type of sequences. In the 3 experiments, the critical interletter intervals were longer between syllables than within syllables, indicating that word syllable structure constrains motor production both in French and Spanish. (PsycINFO Database Record (c) 2010 APA, all rights reserved)     

Phase Composition of Oxide Scales during Reheating in Hot Rolling of Low Carbon Steel

Low carbon steel was oxidized over the temperature range 1000‐1250°C in O₂‐CO₂‐H₂O‐N₂, O₂‐H₂O‐N₂, and O₂‐CO₂‐N₂ gas mixtures. Oxidation times were 12‐120 min. and the scales were 50‐2000 μm thick. The variations of these parameters were chosen to elucidate the phase composition of oxide scales under conditions similar to those of reheating furnaces in hot strip mills, using either thin slab casting or conventional casting and rolling technology. Two types of scales have been observed which are influenced by the furnace atmosphere, oxidation time, and temperature. The first type is a crystalline scale with an irregular outer surface, composed mostly of wustite (FeO), and a negligible amount of magnetite (Fe₃O₄). The second type is the classical three‐layer scale, composed of wustite (FeO), magnetite (Fe₃O₄), and hematite (Fe₂O₃). In general, the experiments showed that an increase in oxidation time decreased the percentage of wustite while the percentages of magnetite and hematite increased. A rise in oxygen concentration in the gas mixture increased the percentages of magnetite and hematite, confirming earlier experimental findings. In water vapour‐free atmospheres O₂‐CO₂‐N₂, the oxide scales had a low percentage of wustite, and high percentage of magnetite and hematite. Carbon dioxide showed a small influence at 1100°C, and a negligible one at 1250°C.     

Morphology development in polyethylene/polystyrene blends: the influence of processing conditions and interfacial modification

The influence of processing conditions and interfacial modification on the morphology evolution and the composition range within which fully co‐continuous high density polyethylene/polystyrene blend structures can exist during blending in a single screw extruder was studied. Blends ranging from pure A to pure B component, with and without compatibilizer, were prepared under two different shear rates. It was found that high shear rates displaced the breakdown–coalescence balance of the dispersed nodules to the side of coalescence, narrowing the percolation domain and the critical composition for full co‐continuity decreased with increasing shear rates. The addition of a tri‐block compatibilizer induced the percolation threshold of the polystyrene phase to begin at lower percentages of polyethylene but the phase inversion point did not change. The experimental results are discussed in the light of various theoretical models. Copyright © 2005 Society of Chemical Industry     

Flow stress of high density polyethylene and nylon 66 at high rates of strain

Measurement of the flow stress of high density polyethylene (HDPE) and nylon 66 at strain rates of 10³ s^?1 using a split Hopkinson pressure bar technique is discussed. The flow stress at a strain of 10% has been determined for both polymers at 20°C. The intrinsic errors involved in this technique are briefly reviewed. The results indicate that the flow stress of HDPE and nylon 66 were 50MPa and 150MPa, respectively, at strain rates of about 10³s^?1.     

导弹动力系统操作训练虚拟仿真器的设计

根据日常训练的需要。设计了导弹动力系统操作训练虚拟仿真器。在深入分析操作规程的基础上，建立该仿真器基于HLA的分布式仿真结构。并对联邦成员内部的仿真逻辑、三维实体建模，基于数据手套和空间方位跟踪仪的人机交互等关键技术进行了研究。     

舞钢管线钢的开发与生产

系统介绍了舞钢开发的针状铁素体型X70宽厚板的设计思路、工艺特点和实物水平；采用电炉 炉外精炼 连铸 TMCP工艺生产的X70宽厚板满足西气东输专用技术条件的要求，并批量应用在西气东输主干线工程中。     

Green and self-lubricating polyoxymethylene composites filled with low-density polyethylene and rice husk flour

Polyoxymethylene (POM) composites filled with low-density polyethylene (LDPE) and rice husk flour (RHF) were prepared by injection molding. The POM/5 wt % LDPE/7.5 wt % RHF composite exhibited the lowest wear rate, whereas the coefficient of friction remained low, and the POM/5 wt % LDPE/5 wt % RHF composite had the best mechanical properties. X-ray diffraction analysis was carried out, and the worn surfaces were examined with scanning electron microscopy. The results showed that the addition of the filler reduced the crystallinity degree of the POM composites. The main wear mechanism for unfilled POM was adhesion, whereas for the POM composites, wear seemed to occur mainly by fatigue and abrasion. It was experimentally confirmed that the POM composite filled with LDPE and RHF, which is well-performing, low-cost, and environmentally friendly, could be a potential material for tribological applications. © 2008 Wiley Periodicals, Inc. J Appl Polym Sci, 2008