Estimating thermal stress in BIPV modules

The thermal stress on building‐integrated photovoltaic modules (BIPV) in Espoo, Finland, was studied with field‐testing of amorphous silicon modules. Based on these results, the thermal stress at two other European locations (Paris and Lisbon) was estimated. The estimation procedure entailed thermal modelling of heat transfer in the façade with meteorological data as input. The results indicate that the thermal stress on BIPV modules in Lisbon is, in this case, approximately 50% higher that in Espoo and between 80 and 200% higher than in Paris, depending on the activation energy of the degradation process. The difference in stress between a BIPV module and a free‐standing module in Espoo was 50–200%. Copyright © 2006 John Wiley & Sons, Ltd.     

钢水化学热法升温技术的研究

依据热力学原理，用计算机计算了某些元素与合金的氧化热效应。综述了各种上化学热法升温技术的应用效果。分析讨论了发热剂的类型，升温速度和热效率问题等。     

液态金属钠高温沸腾实验回路应力分析与强度计算

本文主要完成了液态金属钠高温沸腾实验回路的应力分析与计算，确定了回路高温区连接管系的布置型式和支吊架系统，是该回路总体设计的重要组成部分。     

Adaptive control in a heating vessel: A comparative study

This paper presents experimental results obtained in temperature adaptive control of a heating vessel. A non-linear model of the process showed that the feed flow rate causes severe variations in time constant and process gain. An extended horizon self-tuning controller and two different model reference adaptive controllers were tested. The influence of design parameters on control performance for each algorithm was assessed. The control system was disturbed with load and setpoint changes.     

合成镁白云石砂的研制与应用

选用优质轻烧白云石、轻烧菱镁石为原料,经干法消化、高温煅烧,制得杂质含量2.66％、体密>3.28g/cm~3的合成镁白云石砂。用合成镁白云石砂制得CaO MgO>97％,总杂质含量2.11％的高纯合成镁白云石砖,在太原钢铁公司AOD炉第一次试用,最高炉令达36炉次。     

Development of temperature compensated high elongation resistance strain gauges for use up to 250°C

The paper describes the development and evaluation of temperature compensated high elongation resistance strain gauges for use from room temperature to 250°C. These gauges could be temperature-compensated on steels with coefficient of thermal expansion α = 11 ppm/°C. Thermal output within 250°C was about 1 μm/m/°C and maximum standard deviation of 5 gauges was 34 μm/m. Strain limit was > 4% at room temperature and at 250°C. Gauge factors of different strain ranges at R.T. and at 250°C are tabulated. Some applications are stated.     

Series resonant ZCS‐PFM DC‐DC power converter with high‐frequency high‐voltage transformer link for high‐power magnetron drive

This paper presents a single lossless inductive snubber‐assisted ZCS‐PFM series resonant DC‐DC power converter with a high‐frequency high‐voltage transformer link for industrial‐use high‐power magnetron drive. The current flowing through the active power switches rises gradually at a turned‐on transient state with the aid of a single lossless snubber inductor, and ZCS turn‐on commutation based on overlapping current can be achieved via the wide range pulse frequency modulation control scheme. The high‐frequency high‐voltage transformer primary side resonant current always becomes continuous operation mode, by electromagnetic loose coupling design of the high‐frequency high‐voltage transformer and the magnetizing inductance of the high‐frequency high‐voltage transformer. As a result, this high‐voltage power converter circuit for the magnetron can achieve a complete zero current soft switching under the condition of broad width gate voltage signals. Furthermore, this high‐voltage DC‐DC power converter circuit can regulate the output power from zero to full over audible frequency range via the two resonant frequency circuit design. Its operating performances are evaluated and discussed on the basis of the power loss analysis simulation and the experimental results from a practical point of view. © 2005 Wiley Periodicals, Inc. Electr Eng Jpn, 153(3): 79–87, 2005; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20126     

带化学反应的膛口温度场方程分歧解

提出膛口系统是一种准耗散结构，并分析了符合耗散结构的条件，在分析分歧解线性稳定性的基础上，使用高维定态投影解定态分歧解，分歧解与实验结果吻合较好。     

06NiCuCrMoNb钢高温加热时表层铜的行为

将06NiCuCrMoNb钢试样在不同的加热温度保温不同时间后，观察并分析试样表层的形貌和成分。结果表明，在一定条件下铜会扩散进入表层奥氏体晶界，得到沿奥氏体晶界分布的富铜相，并在热变形加工时导致热脆。试验得到了沿奥氏体晶界分布的富铜相与加热温度和保温时间的关系。