盐浴硫氮碳共渗45钢的接触疲劳性能

对４５钢经盐浴硫氮碳共渗处理的大批试样，进行了滚子接触疲劳性能试验，绘出了Ｐ－Ｓ－Ｎ曲线，分析了接触疲劳断口形貌及破坏机理。     

Pd-Ag-Sn-In-Zn合金时效强化机制研究

通过硬度测试、X射线衍射（XRD）分析、扫描电镜（SEM）观察研究了Pd-Ag-Sn-In-Zn合金时效强化行为及相关的微观结构变化，从而很好地解释了该合金的时效强化机制。结果表明，时效前期合金硬度的增加与在晶界处形成中间过渡相有关。通过扫描电镜观察，可以清楚地看到基体相以及等温时效过程中在晶界处有类似珠光体的析出相。随着稳定第二相的长大，硬度持续下降。     

双包络TI-环面蜗杆传动的二次包络分析

在一次包络分析的基础上,着重进行了二次包络齿面接触分析,推导出了蜗杆和蜗轮齿面方程。齿面接触分析表明：齿面呈双线接触,润滑条件好,承载能力大,在重型机械传动装置中具有实用价值。     

新型硬齿面环面蜗杆传动研究

采用精确磨削TI蜗杆的砂轮，用类似直廓环面蜗杆或平面包络环面蜗杆的磨削方法加工环面蜗杆，使该蜗杆和齿面形状与砂轮曲面相同的蜗轮相配合，形成一种新型蜗杆传动，给出了这种传动蜗杆副齿面的数学模型，并通过计算机仿真得出了这种传动蜗轮齿面上接触线的形状及分布特征，初步分析了其啮合特点。     

金属板料成形数值模拟的研究现状

本文对板料成形数值模拟的几个主要研究方向 :有限元算法、接触与摩擦、成形极限图、缺陷等的研究现状进行了介绍 ,并且讨论了板料成形数值模拟今后的研究方向     

天津爱普生有限公司油墨废水处理方案及运行情况

天津爱普生有限公司废水治理工程设计水量5t／d，废水浓度高，水质、水量变化大。采用水解酸化-生物接触氧化处理工艺对天津爱普生有限公司废水进行处理，进水CODCr，平均为2500mg／L左右，CODCr去除率≥90％，排水各项指标均符合国家污水综合排放标准GB8978-1996的二级排放要求。     

Surface modification of tetrafluoroethylene–perfluoroalkyl vinylether copolymer (PFA) by plasmas for copper metallization

Tetrafluoroethylene–perfluoroalkyl vinylether copolymer (PFA) sheet surfaces were modified with argon, helium, oxygen, and hydrogen plasmas. How the four plasmas modified the PFA sheet surfaces was investigated. All plasmas modified the PFA surfaces and at the same time initiated degradation of the PFA polymer chains. The balance between modification and degradation was strongly influenced by the magnitude of the discharge current in the plasmas. Efficiency of the plasmas in modification was hydrogen plasma > oxygen plasma > argon plasma > helium plasma. The modification involved defluorination of CF₂ carbons into CHF and CH₂ carbons and oxidation into O? CH₂, O? CHF, and O? CF₂ groups. The surface‐modification technique (a combination of hydrogen plasma treatment and silane coupling treatment) proposed in this study was applied for copper metallization of the PFA surface. The utility of the technique was confirmed. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 85: 1087–1097, 2002     

臭氧氧化处理法对聚丙烯表面涂装性的改良 Ⅳ.聚丙烯表面亲水性和涂膜剥离强度的关系

讨论了用臭氧氧化法对聚丙烯表面进行涂装性改良时,丙烯均聚物、乙烯-丙烯嵌段共聚物及无规共聚物表面以接触角表示的亲水性和涂膜剥离强度之间的关系。结果表明,当聚丙烯表面对水的接触角在84°附近时,可反应型涂料的涂膜剥离强度将出现最大值。在此也证明了涂膜的剥离破坏存在着接着破坏和凝集破坏两种机理,当接触角减小到84°及84°以上时,剥离发生在聚丙烯和涂层的界面上产生接着破坏;当接触角减小到84°以下时,剥离发生在聚丙烯的表面氧化层相中,产生凝集破坏。     

Estimating discharge in gravel‐bed river using non‐contact ground‐penetrating and surface‐velocity radars

Discharge measurement is a critical task for gravel‐bed channels. Under high‐flow conditions, the elevation of the riverbed changes significantly by intensive torrential flow. The stage–discharge relations commonly used for stream discharge estimation may no longer be adequate. The contact‐type velocity measuring is also subject to measurement errors and/or instrument failures by the high‐flow velocities, driftwood, stumps, and debris. This study developed a new real‐time method to estimate river discharge in gravel‐bed channels. A systematic measuring technology combining ground‐penetrating radar and surface‐velocity radar was employed. The rating curves representing the relations of water surface velocity to the channel cross‐sectional mean velocity and flow area were established. Stream discharge was then deduced from the resulting mean velocity and flow area. The proposed method was examined in a steep gravel‐bed reach of the Cho‐Shui River in central Taiwan. The estimated stream discharge during three flood events were compared to the prediction by using the stage–discharge relation and the index‐velocity method. The proposed method of this study is capable of computing reasonable values of discharge for an entire flood hydrograph, whereas the other two methods tend to produce large extrapolation errors. Moreover, when the computed discharge is used in 2D flood flow simulation, the proposed method demonstrates better performance than the commonly used stage–discharge and index‐velocity methods.     

Cocurrent downflow circulating fluidized bed (downer) reactors — A state of the art review

In the last decade, cocurrent downflow circulating fluidized bed reactors, called “downer” reactors, have been proposed as an alternative to upflow circulating fluidized bed, or “riser”, reactors. In this paper, published results on downer studies are summarized and future directions of research are recommended. Downer reactors are shown to have several distinct advantages over upflow circulating fluidized bed reactors and can potentially be used in many industrial processes, mainly due to a more uniform gas and solids flow structure compared with risers.