异形柱框架结构设计方法分析与参数控制

近年来,异形柱框架结构(框轻结构体系),因其能较好地满足建筑使用上和结构性能上的要求,而逐步得到了推广应用,并被列为建设部首批住宅建设新技术推荐目录。但异形柱框架结构设计目前还没有可依据使用的国家标准和行业标准。本文根据对江苏省地方标准《钢筋混凝土异形柱框架结构技术规程》(DB32/512-2002)的理解,结合笔者设计实践经验,提出个人看法,供同行参考。     

PLC在环锭捻线机上的应用

介绍了如何使用PLC和数字变频调速技术 ,对传统环锭捻线机进行技术改造 ,使锭速、捻度和卷绕成形变换实现数字化柔性控制 ,扩大了工艺参数的变化范围 ,使整个捻线加工车间实现信息化管理成为可能。     

煤矸石高路堤下多孔拱涵顶进

介绍了国内首例煤矸石高路堤下顶进工程的施工     

10t双电葫芦吊车的改造

介绍了 10t双电葫芦吊车在使用过程中出现的问题 ,提出改造方案     

KTX—1型矿井提升机信号与通讯装置

根据矿山的实际情况,研制开发了矿井提升机信号与通讯装置,介绍了其系统的构成工作原理以及应用效果。     

Solids Extraction of Cod Frame and Effects on Ultrafiltration of the Aqueous Extract

Grinding, pH adjustment, heat treatment and centrifugation were studied to recover solids from ground cod frames and to apply ultrafiltration (UF) to the resulting aqueous phase. Early heat treatment (90°C/20 min) dissolved collagen into aqueous phase resulting in a very low UF flux. A pH adjustment to 4.5 after grinding (～0.32 cm die), with no heat resulted in efficient separation after centrifuging. UF of the aqueous phase showed an increase in initial flux (23 L/hr m²). However, when the same aqueous material was heated and then centrifuged (1–2% solids removed), UF flux was further increased to 46 L/hr m²and this process gave highest solids recovery (90%).     

合山电厂3个机组主厂房定向爆破拆除

介绍了广西合山电厂 1#～3# 机组主厂房定向爆破设计与施工.该工程不仅规模大、环境十分复杂、工期紧、难度高、风险性极强,最大特点是拆除发电设备与爆破同步进行施工.     

Interactive key frame selection model

Video summarization can provide a fine representation of the content of video stream and reduce a large amount of data involved in video indexing, browsing, and retrieval. Moreover, Key frame selection is an important step in the research of content-based video analysis and retrieval. Although there exist a variety of methods for key frame selection, they are heuristic and closed systems, which cannot dynamically generate video summary with user’s preference. In this paper, an M-estimator and epipolar line distance constraint camera motion estimation algorithm is introduced as camera parameters is an important motion feature for key frame selection, and Broyden-Fletcher-Goldfarb-Shanno (BFGS) method is applied to optimize estimated parameters. Moreover, since Interactive Computing is a novel-computing model that represents the transition of algorithm to interaction, an interactive model of key frame selection (IKFS) is presented as a result of improving the model of key frame selection (KFS). The model of KFS and IKFS are proved to satisfy the criterion of induction and coinduction, respectively. Experimental results show that the processing scheme generates flexible and desirable summarizations whose distortion rate is lower than current method. Above all, IKFS is an extension to KFS.     

Casual reasoning in planning1

Reasoning about actions necessarily involves tracking the truth of assertions about the world over time. The SIPE planning system retains the efficiency of the STRIPS assumption for this while enhancing expressive power by allowing the specification of a causl theory. Separation of knowledge about causality from knowledge about actions relieves operators of much of their representational burden and allows them to be applicable in a wide range of contexts. The implementation of causal theories is described, together with examples and evaluations of the system's expressive power and efficiency.     

基于改进PSO算法的结构损伤检测

结构的损伤检测常转化为求解约束优化问题,针对粒子群算法容易出现早熟问题,增大算法后期的粒子位置的改变量,从而增加粒子位置的差异,因而能够增强其在求解约束优化问题时抵抗局部极小的能力。两层刚架单损伤和多损伤识别的数值结果和收敛曲线表明了改进后的粒子群算法优于传统的带惯性因子的粒子群算法。三层框架结构的4种损伤工况的试验研究进一步说明了该算法应用于结构损伤检测领域的有效性。