热作模具钢表面激光堆焊耐磨合金层的研究

本文主要通过在H13钢上用大功率CO_2激光束进行堆焊,阐述了激光堆焊工艺变化对堆焊组织和性能的影响,在本试验条件下,得到了高密度弥散金属化合物组织的激光堆焊层,平均硬度为HV800,与基体呈冶金结合,耐磨性比H13模具钢提高149%。     

多孔板体结构足尺性能分析及材料基本要求

本文就利用诸如蛋白石这样的疏松多孔矿料同灰土构成的混合料，在路面结构中表现出的独特有效的抗冻作用机理作了深入分析，并结合足尺试验数据加以验证。阐述了所谓多孔板体结构的概念、机制和材料组成要求。     

粗粒土渗透变形机制浅析

对砂卵砾石的渗透变形的形成条件进行了简要分析，在此基础上对渗透变形的形式进行了简要评价，并提出了渗透变形临界坡降的计算方法。     

COMPRESSION FATIGUE CRACK GROWTH BEHAVIOUR OF AN ALUMINIUM ALLOY: EFFECT OF OVERLOADING

Abstract— The behaviour of fatigue cracks in an Al-alloy under cyclic compression, either with or without overloads, was studied. For constant-amplitude compressive cycling, a non-catastrophic (saturation) character of the fatigue crack behaviour was confirmed, with the final depth of a crack depending on the applied load level. Single (tensile or compressive) intermittent overloads were shown to re-activate a previously arrested crack while reversed (tensile—compressive or compressive—tensile) ones were also shown to maintain continual fatigue crack extension under otherwise fully compressive cycling.     

一种实时心电图数据压缩算法

提出了一种实时心电图ＥＣＧ数据压缩算法。它是将自适应变门限算法与转折点算法相结合。自适应变门限算法是对ＡＺＴＥＣ算法的改进．它计算ＥＣＧ信号的几个统计参数来确定可变门限值。转折点算法是分析采样点的趋势并只存储每对连续的采样点中的一个。它保留信号的斜坡标志发生变化的峰点和谷点。本文算法兼有这两种算法的优点。这种算法在较高压缩比的情况下重建心电图信号失真较小．     

压缩式致冷设备的电子宽温域多功能控制

设计并研制了一种用于压缩式致冷设备的电子式定温域多功能控制装置。它除具有控温范围宽、精度高、控温参数易调等优点外，还实现了低成本的温度显示、半自动除霜控制、加电延时保护、过欠压保护等功能。全部采用无触点控制方式，有良好的性能／价格比。     

Characteristics of hydrostatic bearing/seal parts for water hydraulic pumps and motors. Part 1: Experiment and theory

In this paper, the load-carrying capacity, power losses and stiffness of disk-type hydrostatic thrust bearings including the case of eccentric loading are discussed theoretically. The numerical analysis method is established based on a two-dimensional elastohydrostatic problem with an elastic deformation model, which is extended to adapt it for a non-axisymmetric load acting on the thrust bearing. The bearing is made of a combination of stainless steel/stainless steel and stainless steel/plastics. For the elastic materials, the maximum stiffness derived from, i.e., minimum film thickness is, larger than that of the rigid material in the range of a large ratio of pocket pressure and a hydrostatic balance ratio of over unity, which is defined as the ratio of the load to the maximum hydrostatic load-carrying capacity. The maximum load-carrying capacity and minimum power loss can exist in the domain of the hydrostatic balance ratio over unity for the case of the bearing consisting of elastic/rigid materials, in comparison with that composed of the same rigid materials. For the case of water, the power loss due to leakage flow is slightly larger but that due to frictional torque is much smaller than that in the case of hydraulic oil. Then, the total power loss is much smaller than that of hydraulic oil.     

具有细小组织的高强度和高延性钢管的开发

介绍了日本川崎制铁公司技术研究所开发出的电焊钢管采用热张力减径工艺的特性 ,及这种钢管的高强度、高延性等基本特性。用这种钢管制造的汽车零部件 ,经弯曲、冲击和疲劳特性等实验 ,证明具有良好的机械加工性能 ,是制造汽车用零部件的优良材料。     

复相材料的循环变形行为

对三种组织状态的F-M复相钢进行了对称和非对称循环加载条件下的形变研究.结果表明,双相钢的循环变形行为,不仅与组织中位错组态的演变过程有关,同时也受循环载荷大小、类型以及加载方式所影响.分析表明,双相钢的循环硬化、软化行为主要受控于两个基本过程,即循环变形时位错组态演变的物理过程和相间分载应力的转嫁、相间残余应力变化的力学过程.     

高层建筑物整体形变的GPS监测

利用GPS观测数据 ,进行高层建筑物的整体形变监测模型和方法的研究是一项重要的工作。本文针对高层建筑物监测环境及其对监测快速、高精度的要求 ,尝试性地提出了高层建筑物整体形变模型 ,说明了模型应用要求和特点 ,详细给出了针对该模型的GPS监测方案 ,并用实例说明了模型和方案的实施步骤 ,实例分析得出了有益结论。