丁集矿副井井架基础沉降变形分析

按井筒冻结施工的进度,选择合适的周期进行沉降变形观测,根据大量的实测资料对冻结施工前后丁集矿副井井架基础的沉降变形规律进行了分析,并预测其沉降变形趋势。     

RMT1-250转换开关用电接触材料

铜铬锆合金是一种形变热处理材料，兼具了铜铬合金和铜锆合金的各种优良性能，经过时效处理的铜铬锆合金，与铜相比，高温强度有很大的改善，而且具有较高的导电率。所以铜铬锆合金广泛应用于电焊机、低压电器等行业。根据对铜铬锆成分的适当调整，可用作为电焊机电极，低压电器触桥、短路环等各种电接触材料。铜铬锆合金用于RMT1－250转换开关，接近于触桥材料的应用，但使用的条件更苛刻一些，要承受部分电弧的侵蚀和由此产生的高温，因此对材料要求具有良好的导电导热性和更高的高温强度。     

热镀锌工艺对Ti-IF钢光整热镀锌板组织和性能的影响

在连续热镀锌线上研究了RTH带钢温度和光整延伸率对Ti—IF钢光整热镀锌板组织和性能的影响。试验表明，当RTH带钢温度在830℃以下时，成品铁素体晶粒度为10．0级，织构类型以{332}、{114}为主，随着带钢温度的进一步提高，热镀锌板的晶粒逐渐粗化，织构成为典型的{111}织构，且取向密度增加，r值随之提高，但当带钢温度在900℃以上时，织构又趋于无规则分布，r值显著降低；光整延伸率对Ti—IF钢光整热镀锌板力学性能的影响很大，随着光整延伸率的提高，屈服强度明显提高，n值明显降低，延伸率降低，抗拉强度变化较小，且光整延伸率对性能的影响与成品铁素体晶粒尺寸有关，成品晶粒越粗，光整延伸率的影响越大。因此对于Ti—IF钢光整热镀锌板而言，n、r值是一对矛盾体，在制订热镀锌工艺时，需根据使用条件的不同，对其n、r值进行综合考虑。     

等径弯角挤压工艺(ECAEP)研究现状

等径弯角挤压是制备块状细晶材料的一种大塑性变形工艺，目前得到国内外高度重视．本文简要介绍了等径弯角挤压工艺的基本原理和变形特点，从理论上对其变形方式和机理进行了分析，并详细介绍了该工艺的应用领域。     

The Region 1 & 3 Broadcasting‐Satellite Service Plan after WRC‐03

The 1977 Broadcasting‐Satellite Service (BSS) Plan for Region 1 & 3 had been widely acknowledged to be out‐of‐date by the late 1980s. Development of digital modulation in the early 1990s provided an opportunity to update the technical provisions of the Plan to make it more economically viable. After a decade of work and three World Radiocommunication Conferences (WRCs), the revision of Region 1 & 3 BSS Plan was finally completed in 2003. The new Plan increased channel assignments from 5 to 10 analog‐equivalent channels for each country in Region 1, and from 4 to 12 channels for each country in Region 3. Yet, despite the increase in capacity, the new Plan is surprisingly similar to the original one in terms of the technical parameters. It is still based on national coverage, and the channel plan, orbital location, orbital spacing, and polarization are also the same. As a result, the new Plan is no more economically viable to implement than the old. To create economically viable BSS systems would most likely require modifications to the assignment in the Plan. Yet, modification procedures were made more difficult to apply after replanning. Less future implementation of BSS networks than would otherwise have occurred can be expected, and an inefficient usage of these frequency bands will likely result. On the other hand, less implemented systems will mean more capacity set aside for future use. This is important for countries that currently do not have satellite operations. In the end, BSS replanning reflects the eternal conflict between efficient usage and guaranteed future access. Copyright © 2005 John Wiley & Sons, Ltd.     

Measurement of the Timoshenko Shear Stiffness. II: Effect of Transverse Compressibility

This is the second of two papers devoted to the issue of measuring the Timoshenko shear stiffness of thin-walled composite beams. In the first paper, the effect of warping on the effective Timoshenko shear stiffness, as measured through bending tests, was studied. The bending test was simulated using finite-element analysis, and the results indicated that the warping effect was minimal. On the other hand, the evidence suggests that transverse flexibility may have a significant influence on the effective Timoshenko shear stiffness, decreasing the effective shear stiffness at shorter test spans. The purpose of the present study is to further investigate this effect and to explore the use of a sandwich theory to predict the measurement error. A higher-order sandwich theory, which captures the transverse strain at concentrated loads and supports, is applied to a commercially available thin-walled composite beam. The results indicate that the sandwich model does capture the decrease in the effective shear stiffness at short spans, and the dependence of the shear stiffness on span-to-depth ratio is similar to that calculated in the first paper, using the finite-element method.     

变形观测与高精度测量机器人系统

介绍了中南大学自行研制开发的高精度测量机器人系统的组成，工作原理，以及该系统实现高精度观测所采取的主要措施；仪器室内检定，野外边频同测，高精度气象改正，周日观测等，同时以某电站大坝的变形观测为例，简单介绍该系统可达到的精度及工程应用领域。     

热压/热变形Nd2Fe14B/α-Fe纳米双相永磁体的研究

为了制备各向异性块状Nd2Fe14B／α—Fe纳米双相永磁体，研究了热压／热变形工艺参数与样品微观组织结构、磁性能之间的关系。结果表明，饱和磁化强度Js随模压温度的升高而提高；而剩磁Jr、内禀矫顽力Hcj和最大磁能积(BH)max开始都随模压温度的升高而上升，但超过一定温度后反而降低；同时提高热压压力会使磁性能增加，而热变形温度对磁性能影响很小。热变形后样品垂直于压力方向的磁性能略高于平行于压力方向，呈现出轻微的各向异性。Nd2Fe14B／α—Fe纳米双相永磁材料在热压／热变形后没有产生晶粒的择优长大，在晶体学上仍然是各向同性的。     

大塑性变形制备纳米结构金属

细化晶粒是改善材料性能的有效手段，传统的压力加工技术(如轧制、挤压、拉拔和锻造等)可以细化晶粒(微米量级)。纳米结构金属由于具有很小的晶粒尺寸(20-500nm)和独特的缺陷结构，从而表现出优异的物理—力学性能。大塑性变形(SPD)具有将铸态粗晶金属的晶粒细化到纳米量级的巨大潜力，近年来已引起人们的极大关注。介绍了4种大塑性变形制备纳米结构金属的方法、原理、变形特点及应用，分析了纳米结构金属的强度和超塑性变形特征，以及当前研究中存在的主要问题，并对大塑性变形技术的应用前景进行了展望。     

Study on Hot Deformation Cracks of Steel D2 Using Procesing Map

ＳｔｕｄｙｏｎＨｏｔＤｅｆｏｒｍａｔｉｏｎＣｒａｃｋｓｏｆＳｔｅｅｌＤ２ＵｓｉｎｇＰｒｏｃｅｓｉｎｇＭａｐＧａｏＳｈａｎ，ＬｉｕＸｉａｎｇｈｕａ，ＷａｎｇＧｕｏｄｏｎｇＡＢＳＴＲＡＣＴＴｈｅｈｏｔｄｅｆｏｒｍａｔｉｏｎｂｅｈａｖｉｏｒｓｏｆｓｔｅｅｌ...