Evidence of High Vertical Wave-Number Behavior in a Continuously Stratified Reservoir: Boadella, Spain

High vertical wave-number modes clearly dominate the internal wave field during the stratification period in Boadella reservoir in northeast Spain. In this period, the extraction of hypolimnetic water, due to summer irrigation, brought the surface level down by 6 m in one month and the epilimnetic water progressively occupied the whole water column. The temperature profile, with the exception of a few meters at the surface layer, presented an almost constant temperature gradient of about 0.7°C/m. The period of the main vertical mode is 24 h with an amplitude of around 1 m. Thermistor chain records and meteorological data allow us to deduce that this mode is, at least, a third vertical mode forced by the wind, which normally has a typical periodicity of 24 h. However, when the wind changes direction from south to north, the circulation cells developed due to this forced nonstationary oscillation are destroyed. When this occurs, the Bulk Richardson number is Rib ～ 1. Similar vertical structures as a response to wind forcing should be expected in similar systems, although this has not been reported in the literature.     

Control of Wind-Induced Self-Excited Oscillations by Transfer of Internal Energy to Higher Modes of Vibration. II: Application to Taut Cables

In Part I of this paper, a theoretical basis is presented using a two-degrees-of-freedom model. In this second part of the study, the passive control and the two types of semiactive controls introduced in Part I are examined numerically for a taut cable experiencing wind-induced galloping motion. The passive and the semiactive control schemes for taut cables show a good similarity with the results obtained for the two-degrees-of-freedom model. The potential of using these control schemes in practical applications to flexible structures is demonstrated.     

Assessment of Shear Forces on Bridge Abutments: Simplified Method

The conventional application of reduction factors to response spectrum analysis results is inappropriate for the abutment shear forces, which are based on elastic action. On the other hand, adopting the unreduced values from the elastic dynamic analysis does not achieve equilibrium among the abutment shear forces, deck inertia forces, and reduced pier forces. A simplified method is here proposed for the assessment of the shear on the abutments, documented by comparison with response spectrum and time history nonlinear analyses for several bridge configurations. For the analyzed configuration of the bridge with an internal movement joint, the response spectrum analysis underestimates the shear on the abutment for low values of the abutment flexibility and overestimates it when the stiffness of the abutments becomes higher than that of the piers. In all the case studies analyzed, the proposed method approximates the time history results better than the response spectrum.     

Thermally stimulated shrinkage forces in oriented polymers: 1. Temperature dependence

Temperature dependences of shrinkage forces appearing in oriented polymer samples when heated at constant length were recorded for polycarbonate, polyethylene terephthalate, polyethylene and polypropylene. The influence of various processing conditions on thermally stimulated shrinkage forces is demonstrated. A four-state model is proposed which qualitatively describes the temperature dependences of shrinkage forces in amorphous polymers.     

Ti/Al Interaction and Austenite Grain Control in Crankshaft Manufacturing with 38MnSiVS5 Steel

38MnSiVS5 steel is similar to 38MnVS6 steel (EN), the difference being the addition of a small Ti content. Typical Ti and Al contents in the chemical composition of 38MnSiVS5 steel are Ti=0.020 and Al=0.035 mass%. Both elements combine easily with nitrogen, especially Ti, and it has been observed that relatively high Al levels are harmful for austenite grain size control at reheating temperatures. In this work 38MnSiVS5 steel is used to manufacture a large number of castings, varying only the Ti and Al contents and obtaining ingots with a different Ti/Al ratio in each case. The results show that abnormal growth of the austenitic grain occurs irrespective of the Ti and Al contents, due fundamentally to the partial dissolution and coarsening of TiN precipitates. However, the steels with high Al contents present worse behaviour due to the formation of a second type of precipitates, namely AIN, which quickly dissolve between 1000 and 1100°C, causing a drastic decline in local pinning forces that gives rise to more pronounced abnormal growth of the affected grains.     

THE STICKY ISSUES OF DRYING

Unconrolled agglomeration of particles and adhesion of the particulate mass to wall surfaces are common severe problems in many drying operations. This paper reviews the mechanisms of interparticle and particle-surface attraction as well as the theory and the existing tests for characterising powders in terms of internal strength, wall friction and adhesion. The usefulness of the information obtained from these tests in dryer design and operation is critically reviewed. The importance of powder stickiness in various types of dryers is discussed and established methods of combating the problem are presented Recommendations an made for further research in the area of powder cohesion and adhesion.     

强化两相混合的超临界技术制备聚乳酸微粒

针对商品化聚乳酸微球粒径分布较宽难于适用气溶胶给药要求的不足,采用水力空化混合强化超临界流体辅助雾化技术(SAA-HCM)制备聚乳酸(PLA)超细微粒.该技术主要特点是通过在超临界流体和液相进料处引入水力空化混合器,强化两相间的混合.考察SAA-HCM过程混合器压力、温度、沉淀器温度、进料中CO2与液体溶液质量流量比和溶液质量浓度等操作参数对微粒形态和粒径分布的影响,成功制备出球形度较好,粒径分布较窄(1～3μm)的PLA微球.经X射线衍射(XRD)分析和差示扫描量热(DSC)分析显示,与原料PLA相比,微球晶型及热曲线变化不大,但结晶度下降.同时把操作参数与相行为进行关联,探讨了影响颗粒形貌的机理.对比超临界流体辅助雾化法(SAA)的实验结果表明:水力空化的引入能有效强化混合器内的两相传质,混合更好,能制备出适用于气溶胶给药要求的超细微粒.     

纳米管合成研究进展

当今纳米科学技术飞速发展，其中纳米管已构成了纳米材料的一个非常重要的类别。本文介绍近几年来由化学键结合的纳米管以及由分子间力形成的一些纳米或具有中观尺度的管状结构材料的合成研究进展。     

顶部定常吸气对高层建筑模型气动力的影响

为减少高层建筑受到的风荷载,提高高层建筑抗风性能,提出一种顶部吸气的主动控制方法。在一高宽比为H/d=5的正方形截面柱体的高层建筑模型上,通过在其顶部前边缘开设狭缝进行吸气来实现流动控制。通过风洞试验研究了顶部吸气对气动力与顶部分离流的影响.利用流动可视化与流场测试结果揭示了顶部狭缝吸气的控制机理.实验对比了不同吸气系数Q(=U/U_∞,U为狭缝吸气速度)对气动力控制效果的影响,并对Q=0,1和3的三种工况下风压分布与顶部剪切流进行了详细对比.研究发现狭缝吸气改变了顶部分离流特性,并对模型所有高度上的气动力均有显著影响.Q=1时控制效果最佳,脉动阻力与脉动升力分别减小17.8%和45.5%.此时顶面分离流被削弱并伴随有再附现象且湍流强度较大,最有利于顶部剪切流与尾流间的动量交换,从而削弱柱体展向涡脱落与脉动气动力.     

基于支持向量机的红细胞彩色图像分割

对红细胞进行精确的分割并统计各类参数在临床医学中有着重要的意义,但现有经典算法很难实现自动分割并获得较高准确率。红细胞的分割主要有两个难点：一是红细胞的目标提取;二是重叠红细胞的分割。本文首先利用SVM对原始图像进行红细胞提取,把原始细胞分割成红细胞和背景两类目标区域,然后对红细胞区域进行重叠分割（本文中使用改进距离标记的分水岭算法）,最终得到各个红细胞的统计数据。为获得最佳的分割效果,本文通过实验对核函数、支持向量类型及相关参数进行了详细的比较和分析。实验结果表明,该算法能有效、快捷、准确、全自动的实现