铸态及快淬态无钴AB5型贮氢合金的循环稳定性

对AB5型LaxMm1-x(NiMnSiAlFe)49(x=0,0.45,0.75,1.00,摩尔分数)贮氢合金进行了快淬处理,研究了La含量及快淬工艺对合金微观结构及电化学循环稳定性的影响.结果表明:La含量的增加对铸态合金的循环稳定性没有明显影响,但使快淬态合金的循环稳定性下降,且快淬处理能显著提高合金的循环稳定性.当La替代量从0增加到1.00时,经300次充放循环后,铸态合金的容量保持率(Rh)从59.2%增加到59.8%;16 m/s淬速快淬态合金的容量保持率从83.9%下降到65.0%.对于x=0.45的合金,当淬速从0(铸态被定义为淬速等于0)增加到28 m/s时,容量保持率从59.8%增加到75.8%.     

二元稀土系AB5型贮氢电极合金的放电容量与晶胞体积和4f电子浓度的关系

制备了6个系列通式为AαA‘1-αB5的RE(NiCoMnTi)5贮氢电极合金(其中，AαA‘1-α为La，Ce，Pr，Nd4个元素中任意2个的组合)，测定了它们在100次循环中的最大放电容量Cmax及部分合金的晶胞体积Vcell．结果表明：Cmax主要由Vcell决定，Cmax先随Vcell的增大而增加，在Vcell≈85．66x10^-^3。nm^3时达到一极大值，然后又随Vcell的增大而减小；同时，Cmax还与4f电子浓度ne4f／naRE有关，A侧具有相同4f电子浓度的合金其Cmax随4f电子浓度的变化趋势相似．     

Hyperhomocysteinemia and Cardiovascular Disease: Is the Adenosinergic System the Missing Link?

The influence of hyperhomocysteinemia (HHCy) on cardiovascular disease (CVD) remains unclear. HHCy is associated with inflammation and atherosclerosis, and it is an independent risk factor for CVD, stroke and myocardial infarction. However, homocysteine (HCy)-lowering therapy does not affect the inflammatory state of CVD patients, and it has little influence on cardiovascular risk. The HCy degradation product hydrogen sulfide (H₂S) is a cardioprotector. Previous research proposed a positive role of H₂S in the cardiovascular system, and we discuss some recent data suggesting that HHCy worsens CVD by increasing the production of H₂S, which decreases the expression of adenosine A_2A receptors on the surface of immune and cardiovascular cells to cause inflammation and ischemia, respectively.     

多孔纤维型重整微反应器的等效电阻网络建模

针对应用于重整制氢微反应器的复杂多孔金属纤维载体（PFS）的流速场高效分析难题,建立载体中随机微通道的等效电阻网络分析模型. 基于复杂随机纤维结构的统计网络模型,将纤维载体中三维联通的随机微通道结构及与之相连的进出口腔简化为规则的网络通道结构.借鉴基尔霍夫定律,建立纤维载体的等效电阻网络模型,并确定求解方法. 纤维载体流速场实例分析的结果表明,基于等效电阻网络模型求解的纤维载体流速场与计算流体力学(CFD)方法的结果之间的皮尔森相关系数约为98%,且求解效率约为CFD方法的2.9×10⁴倍. 研究成果为多孔纤维型重整制氢微反应器的设计制造提供了新的支撑方案.     

Structural stability of single-layered LaNi4.25Al0.75 film and its electrochemical hydrogen-storage properties

AB5-based hydrogen storage thin fdms （LaNi4.25Al0.75）, deposited on Cu substrate by dc magnetron sputtering were investigated in this study. X-ray diffraction （XRD） revealed that the microstructure of the layer was in crystal form. SEM and AFM analyses proved that the film appeared to be rather rough with numerous randomly sized pores of approximately 15-40 in nm diameter. Structural stability of the film was examined by the combined analyses of DSC, XRD, and SEM, which indicated that this film maintained its structural stability below 500 K or so, and a network structure was observed on the film after being heated at 700 K for 30 min. Electrochemical hydrogen-storage properties of the films were investigated by simulated battery tests. It was found that single-layered LaNi4.25A10.75 film exhibited electrochemical hydrogen-storage properties similar to typical AB5 alloys in bulk, and the maximum discharge capacity of the film was about 220 mAh/g. After 20 charge/discharge cycles, small needle-shaped aluminium oxide was formed on some fractions of the film surface.     

金属陶瓷防腐蚀涂层替代镀镉或镉−钛工艺的研究

针对钢制零件采用镀镉、镀镉?钛工艺存在氢脆、镉脆风险及不利于环境保护的现状,研究采用涂覆IPcote9183或IPcote9183+IPseal9184形成金属陶瓷防腐蚀涂层(MCAC)的替代工艺。对比结果表明:上述2种金属陶瓷涂层的氢脆性和耐蚀性优于镉及镉?钛镀层,其他性能相当,能够完全替代它们应用于起落架钢制零件的表面防护。     

Hydrogen Sulfide Metabolite,Sodium Thiosulfate: Clinical Applications and Underlying Molecular Mechanisms

Thiosulfate in the form of sodium thiosulfate (STS) is a major oxidation product of hydrogen sulfide (H₂S), an endogenous signaling molecule and the third member of the gasotransmitter family. STS is currently used in the clinical treatment of acute cyanide poisoning, cisplatin toxicities in cancer therapy, and calciphylaxis in dialysis patients. Burgeoning evidence show that STS has antioxidant and anti-inflammatory properties, making it a potential therapeutic candidate molecule that can target multiple molecular pathways in various diseases and drug-induced toxicities. This review discusses the biochemical and molecular pathways in the generation of STS from H₂S, its clinical usefulness, and potential clinical applications, as well as the molecular mechanisms underlying these clinical applications and a future perspective in kidney transplantation.     

Improvement of flexural bond strength of zirconia-resin cement by surface patterning using sub-nanosecond UV laser

Zirconia is a dental material that shows excellent biocompatibility and high strength in clinical applications. This study aims to evaluate the effects of ultrafast laser applications. The surface nanostructures were classified into three groups. Group 1 was generated using the burst mode, with three different distances between dots: 52 µm (Group 1a), 104 µm (Group 1b), and 156 µm (Group 1c). Group 2 was processed using the scanning mode configuration, with a set of parallel lines. Group 3 was also processed using this scanning configuration creating a set of square-shaped patterning. Group 4 was the control group. After the surface treatments, a pair of zirconia specimens was bonded end to end with resin cement. Flexural bond strength (FBS) test was applied in a universal test machine. Multiple comparisons were performed using a one-way analysis of variance and the Tukey's HSD test. All the samples that were treated with the laser showed higher FBS values than the untreated surface. Using the burst mode, preformed circular-shaped surface on an angle of 90⁰ at 52 µm distance (Group 1a) showed the highest FBS values among all groups (p < .05). Groups 2 and 3 had significantly higher values than 1b and 1c.     

蒽醌法合成过氧化氢催化剂的研究进展

过氧化氢（H₂O₂, 俗称双氧水）, 由于其强氧化性常用作漂白剂、消毒剂, 同时也作化工原料。目前工业上生产过氧化氢的主要方法为蒽醌法, 全球近99%的产品均通过蒽醌法制得。研究具有高活性、高选择性及经济性的催化剂是合成过氧化氢所面对的最具挑战性的课题, 同时也是工业催化领域的研究热点之一。主要针对蒽醌法制过氧化氢催化剂, 综述了各种活性组分、载体及助剂在蒽醌加氢催化剂中的研究进展, 并简单探讨了各种活性组分的优缺点, 概括了各种载体、助剂的作用, 以期对过氧化氢催化剂的合成制备提供一些有益的启示。     

合金元素P,Cu含量对铸铁短纤维结合剂组织和性能的影响

本文研究了合金元素磷和铜对铸铁短纤维烧结体显微组织和性能的影响。结果表明，合金元素磷可显著提高铸铁短纤维烧结体的密度、致密化系数和压强度。磷与铜的共同加入可进一步提高烧结体的压溃强度和硬度，同时，铜的加入可抑制由磷引起的烧结体的急剧。烧结机理随磷、铜含量的增加逐渐由固相烧结＋瞬态液烧结转变为液相烧结。