变质处理对挤压态Al-20Mg2Si-4.5Cu合金初生及共晶Mg2Si变质形貌的影响机制

目的 研究微量元素复合变质下挤压态Al-20Mg2Si-4.5Cu合金初生Mg2Si和共晶Mg2Si的形貌演化规律,揭示Mg2Si相的变质和球化机制。方法 采用形貌调控元素Be和异质形核元素Sb协同变质调控初生及共晶Mg2Si相的形貌,然后结合挤压工艺对初生及共晶Mg2Si形貌进行进一步调控。结果 经0.5%(质量分数)Be-Sb复合变质与挤压工艺处理后,初生Mg2Si转变为近球形,尺寸约为10 μm,共晶Mg2Si转变约1 μm的球形。结论 挤压变形可以使Be-Sb复合变质后的合金中的初生及共晶Mg2Si相发生明显球化。其中,Sb元素生成的Mg3Sb2相作为初生Mg2Si的异质核心,有效细化了初生Mg2Si相;Be元素选择性吸附在初生Mg2Si及共晶Mg2Si的择优生长晶面上。     

Design of an aeronautic pitot probe with a redundant heating system incorporating phase change materials

The aim of this work is the design of a pitot probe (PP) prototype in order to retard the cool down of the tip, in case of a heating element failure. The viability of operation in flight conditions is evaluated. The design consists of a redundant heating system incorporating phase change materials (PCM). Combining experimental observations of ice formation with the implementation of the conjugate heat transfer (CHT) model, with the addition of the heat release due to the phase change of the PCM, the numerical evaluation is developed. The modelling assumptions and numerical implementation of the phase change process are presented. Then, the selection an appropriate PCM is based on the low flammability and volume dilation and the quantitative effects of the material properties on the heat transfer. A commercial PCM solution based on salt hydrates was chosen as the most adequate for the design. The parametric design of the prototype, based on the design of experiment method and fractional factorial testing, is established. A multiple linear regression model was obtained in order to maximize the cooling retardation. The numerical simulations demonstrate that the prototype PP tip temperature remains 194 s longer above 0 °C than that of the conventional model analyzed.     

使用溅射AlN成核层实现大规模生产深紫外LED

高质量AlN薄膜对制造高性能深紫外器件非常重要,但是目前还很难使用大型工业MOCVD生长出高质量的AlN薄膜.采用磁控溅射制备了不同厚度的用作成核层的AlN薄膜,使用大型工业MOCVD直接在成核层上高温生长AlN外延层,研究了不同成核层对AlN外延层质量的影响.通过扫描电子显微镜和原子力显微镜对成核层AlN薄膜的表面形貌进行表征;使用高分辨X射线衍射仪对AlN外延层晶体质量进行表征,结果表明:在溅射成核层上生长的AlN外延层的晶体质量有显著提高.使用大型工业MOCVD在蓝宝石衬底上成功制备出中心波长为282 nm的可商用深紫外LED,在注入电流为20 mA时,单颗深紫外LED芯片的光输出功率达到了1.65 mW,对应的外量子效率为1.87%,饱和光输出功率达到4.31 mW.     

C60与金刚石薄膜成核关系的研究

采用热丝化学气相沉积法在覆盖C60膜的硅基片上沉积金刚石膜,研究了金刚石膜的成核与生长.实验结果表明,金刚石的成核密度可达1×106Cm-2,利用这种方法可实现衬底无损淀积金刚石膜.C60之所以能够促进金刚石成核,我们认为主要与C60分子本身独特的结构及H原子的激活作用有关.同时,高温下C60分解后残留的石墨等碳碎片以及C原子与衬底Si反应生成的SiC都可作为金刚石的成核位.     

NUMERICAL SIMULATION OF THE FORMATION OF NANOPARTICLES IN AN IMPINGING TWIN-JET

The Large Eddy Simulation (LES) method has been used to solve the fluid momentum equations coupled with a convection-diffusion equation to study the formation of pollutant nanoparticles in a vehicular exhaust with impinging twin-jet. The functions of the space (S) between the two jets and the distance (H) from the exit of nozzle to the impingement plane are evaluated according to the distributions of pollutant nanoparticles. The results show that the nucleation produces a large number of nanoparticles, and gas-to-nanoparticle conversion mostly takes place in the interface region of the two jets, the circumambience of the jets, and region near the plane. The maximal particle size and maximal number concentration produced by both nucleation and coagulation appear around the region of free jet and the region near the plane, respectively. The significant differences for various spaces between the two jets are the number concentration and size distributions in the interface region of the two jets. For the case with larger space, more nanoparticles are produced by nucleation and coagulation. The more the distance from the exit of nozzle to the impingement plane, the lower is the number concentration and the fewer the particles distribute near the plane. Increasing the distance from nozzle to plane is beneficial to the reduction of nanoparticle formation.     

超音速喷嘴涡流管气体分离性能的数值模拟与实验

 建立了超音速喷嘴涡流管的简化几何模型,利用描述两相双组分超音速冷凝流动的 Eulerian 双流体三维湍流模型,以含湿空气为介质对装置内部的自发凝结过程进行数值模拟。设计制造相应的装置,建立实验平台,对装置的含湿气体分离性能进行实验研究。通过模拟和实验2种手段研究了影响超音速喷嘴涡流管气体分离性能的参数及其影响规律。结果表明,气流在喷嘴内部达到超音速流动,使得水蒸气自发凝结成液滴,为混合气体分离提供了先决条件;热端管内气体自旋产生的离心加速度可以达到重力加速度的6×10⁵倍,为气、液分离提供了必要条件;降低进出口压力之比和冷流率,增大入口相对湿度和长径比可以提高装置的气体分离性能,安装阻涡器对性能有不利影响。因此,采用超音速喷嘴涡流管实现混合气体中重组分的脱除是可行的。     

2008年桂北架空线路覆冰的初步分析

根据2008年广西桂北电网遭受雨雪冰冻灾害的覆冰特点,对强冷空气入侵的天气变化过程、覆冰形成的条件、线路覆冰厚度的计算、本次覆冰的特点、重现期的评估以及实际冰厚与气象区划的比较等多方面进行分析,提出加强电网抗冰能力的建议.     

Synthesis of Millimeter‐Scale Transition Metal Dichalcogenides Single Crystals

The emergence of semiconducting transition metal dichalcogenide (TMD) atomic layers has opened up unprecedented opportunities in atomically thin electronics. Yet the scalable growth of TMD layers with large grain sizes and uniformity has remained very challenging. Here is reported a simple, scalable chemical vapor deposition approach for the growth of MoSe₂ layers is reported, in which the nucleation density can be reduced from 10⁵ to 25 nuclei cm^?2, leading to millimeter‐scale MoSe₂ single crystals as well as continuous macrocrystalline films with millimeter size grains. The selective growth of monolayers and multilayered MoSe₂ films with well‐defined stacking orientation can also be controlled via tuning the growth temperature. In addition, periodic defects, such as nanoscale triangular holes, can be engineered into these layers by controlling the growth conditions. The low density of grain boundaries in the films results in high average mobilities, around ≈42 cm² V^?1 s^?1, for back‐gated MoSe₂ transistors. This generic synthesis approach is also demonstrated for other TMD layers such as millimeter‐scale WSe₂ single crystals.     

绝热剪切带内微孔洞演化规律研究

为深入了解绝热剪切带内微孔洞的演化规律,进而揭示高应变率加载条件下绝热剪切破坏的特殊规律,本文对D35钢进行了约束爆破实验,爆破后回收圆筒的微观观察表明,绝热剪切破坏要经过绝热剪切带内微孔洞形核、长大和相互联接形成裂纹等一系列演化过程.在Guduru P等人的测试结果和Li Shaofan等人数值仿真结果基础上,通过简化(剪切带内的温度分布为由剪切带中心向边缘线性降低,并最终降至与基体温度相同; 微孔洞的形核、长大受温度控制,长大速度随温度呈指数规律降低)对Timothy S P和Hutchings I M的模型进行了修正,修正后的模型可以定量的描述绝热剪切带内微孔洞的演化直至破坏的全过程,模型的描述与微观分析获得的实验结果有较好的一致性.     

基于声表面波技术的飞机结冰预警系统研究

飞机结冰严重影响飞行安全,现有结冰传感器都只在飞机结冰后才进行告警。利用声表面波结冰传感器及声表面波温度传感器设计了飞机结冰预先告警系统。研究了声表面波结冰传感器的原理,并设计了传感器信号的告警逻辑关系,通过等效电路对无线声表面波冰传感器进行仿真。仿真结果表明,声表面波飞机结冰预警系统可用以降低结冰信号的虚警率。